CAT5171

CAT5171 256-Position I2C Compatible Digital Potentiometer The CAT5171 is a 256−position digitally programmable linear taper potentiometer ideally suited for replacing mechanical potentiometers and variable resistors. The wiper settings are controlled through an I2C−compatible digital interface. Upon power−up, the wiper assumes a midscale position and may be repositioned anytime after the power is stable. The device can be programmed to reset the wiper position to midscale or to go to a shutdown state during operation. An address input pin, AD0, allows the connection of two devices onto the same I2C bus. The CAT5171 operates from 2.7 V to 5.5 V, while consuming less than 2 mA. This low operating current, combined with a small package footprint, makes the CAT5171 ideal for battery−powered portable applications. The CAT5171, designed as a pin for pin replacement for the AD5245, is offered in the 8−lead SOT23 package and operates over the −40°C to +85°C industrial temperature range. Features http://onsemi.com SOT23−8 TP, TB SUFFIX CASE 527AK MARKING DIAGRAM • • • • • • • • • 256−position End−to−End Resistance: 50 kW, 100 kW I2C Compatible Interface Power−on Preset to Midscale Single Supply 2.7 V to 5.5 V Low Temperature Coefficient 100 ppm/°C Low Power, IDD 2 mA max Wide Operating Temperature −40°C to +85°C RoHS−compliant SOT−23 8−Lead (2.9 mm x 3 mm) Package AFYM 1 1 AGYM AF = 50 kW AG = 100 kW Y = Production Year Y = (Last Digit) M = Production Month M = (1 − 9, A, B, C) Typical Applications • Potentiometer Replacement • Transducer Adjustment of Pressure, Temperature, Position, • • Chemical, and Optical Sensors RF Amplifier Biasing Gain Control and Offset Adjustment PIN CONNECTIONS W VDD GND SCL (Top View) 1 A B AD0 SDA ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. © Semiconductor Components Industries, LLC, 2009 August, 2009 − Rev. 1 1 Publication Order Number: CAT5171/D CAT5171 VDD SCL SDA AD0 Power On Midscale GND A I2C Interface and Control W B Figure 1. Functional Block Diagram Table 1. ORDERING INFORMATION Part Number CAT5171TBI−50GT3 CAT5171TBI−00GT3 Resistance 50 kW 100 kW Temperature Range −40°C to 85°C Package SOT−23−8 (Pb−Free) Shipping† 3000/Tape & Reel 3000/Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Table 2. PIN FUNCTION DESCRIPTION Pin No. 1 2 3 4 5 6 7 8 Pin Name W VDD GND SCL SDA AD0 B A Resistor’s Wiper Terminal Positive Power Supply Digital Ground Serial Clock Input Serial Data Input I2C Address bit 0 input Description Bottom Terminal of resistive element Top Terminal of resistive element Table 3. ABSOLUTE MAXIMUM RATINGS (Note 1) Rating VDD to GND VA, VB, VW to GND IMAX Digital Inputs and Output Voltage to GND Operating Temperature Range Maximum Junction Temperature (TJMAX) Storage Temperature Lead Temperature (Soldering, 10 sec) Value −0.3 to 6.5 VDD ±20 0 to 6.5 −40 to +85 150 −65 to +150 300 mA V °C °C °C °C Unit V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Maximum terminal current is bounded by the maximum current handling of the switches, maximum power dissipation of the package, and maximum applied voltage across any two of the A, B, and W terminals at a given resistance. http://onsemi.com 2 CAT5171 Table 4. ELECTRICAL CHARACTERISTICS: 50 kW and 100 kW Versions VDD = 2.7 V to 5.5 V; VA = VDD; VB = 0 V; –40°C < TA < +85°C; unless otherwise noted. Parameter DC CHARACTERISTICS — RHEOSTAT MODE Resistor Differential Nonlinearity (Note 3) Resistor Integral Nonlinearity (Note 3) Nominal Resistor Tolerance (Note 4) Resistance Temperature Coefficient Wiper Resistance RWB, VA = no connection RWB, VA = no connection TA = 25°C VAB = VDD, Wiper = no connection VDD = 5 V, IW = ±3 mA VDD = 3 V, IW = ±3 mA DC CHARACTERISTICS — POTENTIOMETER DIVIDER MODE Resolution Differential Nonlinearity (Note 5) Integral Nonlinearity (Note 5) Voltage Divider Temperature Coefficient Full−Scale Error Zero−Scale Error RESISTOR TERMINALS Voltage Range (Note 6) Capacitance (Note 7) A, B Capacitance (Note 7) W Common−Mode Leakage (Note 7) DIGITAL INPUTS Input Logic High Input Logic Low Input Logic High Input Logic Low Input Current POWER SUPPLIES Power Supply Range Supply Current Power Dissipation (Note 7) Power Supply Sensitivity Bandwidth –3 dB Total Harmonic Distortion VW Settling Time (50 kW/100 kW) VIH = 5 V or VIL = 0 V VIH = 5 V or VIL = 0 V, VDD = 5 V nVDD = +5 V ±10%, Code = Midscale RAB = 50 kW / 100 kW, Code = 0x80 VA =1 V rms, VB = 0 V, f = 1 kHz, RAB = 10 kW VA = 5 V, VB = 0 V, ±1 LSB error band VDD RANGE IDD PDISS PSS BW THDW tS 100/40 0.05 2 2.7 0.3 5.5 2 0.2 ±0.05 V mA mW %/% kHz % ms VDD = 5 V VDD = 5 V VDD = 3 V VDD = 3 V VIN = 0 V or 5 V VIH VIL VIH VIL IIL 0.7 x VDD 0.3VDD ±1 0.7 x VDD 0.3VDD V V V V mA f = 1 MHz, measured to GND, Code = 0 x 80 f = 1 MHz, measured to GND, Code = 0 x 80 VA = VB = VDD/2 VA,B,W CA,B CW ICM GND 45 60 1 VDD V pF pF nA Code = 0x80 Code = 0xFF Code = 0x00 N DNL INL nVW/nT VWFSE VWZSE −3 0 −1 −1 ±0.1 ±0.4 100 −1 1 0 3 8 +1 +1 Bits LSB LSB ppm/°C LSB LSB R−DNL R−INL nRAB nRAB/nT RW −1 −2 −20 100 50 100 120 250 ±0.1 ±0.4 +1 +2 +20 LSB LSB % ppm/°C W Test Conditions Symbol Min Typ (Note 2) Max Unit DYNAMIC CHARACTERISTICS (Notes 7 and 9) 2. Typical specifications represent average readings at +25°C and VDD = 5 V. 3. Resistor position nonlinearity error R−INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper positions. R−DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic. 4. VAB = VDD, Wiper (VW) = no connect. 5. INL and DNL are measured at VW with the digital potentiometer configured as a potentiometer divider similar to a voltage output D/A converter. VA = VDD and VB = 0 V. DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions. 6. Resistor terminals A, B, W have no limitations on polarity with respect to each other. 7. Guaranteed by design and not subject to production test. 8. Maximum terminal current is bounded by the maximum current handling of the switches, maximum power dissipation of the package, and maximum applied voltage across any two of the A, B, and W terminals at a given resistance. 9. All dynamic characteristics use VDD = 5 V. http://onsemi.com 3 CAT5171 Table 5. CAPACITANCE TA = 25°C, f = 1.0 MHz, VDD = 5 V Symbol CI/O (Note 10) Test Input/Output Capacitance (SDA, SCL) Conditions VI/O = 0V Max 8 Units pF Table 6. POWER UP TIMING (Notes 10 and 11) Symbol tPUR tPUW Power−up to Read Operation Power−up to Write Operation Parameter Max 1 1 Units ms ms 10. This parameter is tested initially and after a design or process change that affects the parameter. 11. tPUR and t PUW are delays required from the time VCC is stable until the specified operation can be initiated. Table 7. DIGITAL POTENTIOMETER TIMING Symbol tWRPO tWR Parameter Wiper Response Time After Power Supply Stable Wiper Response Time: SCL falling edge after last bit of wiper position data byte to wiper change Min Max 50 20 Units ms ms Table 8. A.C. CHARACTERISTICS VDD = +2.7 V to +5.5 V, −40°C to +85°C unless otherwise specified. Symbol fSCL tHIGH tLOW tSU:STA tHD:STA tSU:DAT tHD:DAT tSU:STO tBUF tR tF tDH TI tAA Clock Frequency Clock High Period Clock Low Period Start Condition Setup Time (for a Repeated Start Condition) Start Condition Hold Time Data in Setup Time Data in Hold Time Stop Condition Setup Time Time the bus must be free before a new transmission can start SDA and SCL Rise Time SDA and SCL Fall Time Data Out Hold Time Noise Suppression Time Constant at SCL, SDA Inputs SCL Low to SDA Data Out and ACK Out 100 50 1 600 1300 600 600 100 0 600 1300 300 300 Parameter Min Typ Max 400 Units kHz ns ns ns ns ns ns ns ns ns ns ns ns ms http://onsemi.com 4 CAT5171 TYPICAL CHARACTERISTICS 0.03 0.02 0.01 0 ERROR (LSB) ERROR (LSB) −0.1 −0.2 −0.3 −0.4 −0.5 INL DNL 0.1 0 −0.01 −0.02 −0.03 −0.04 −0.05 0 32 64 96 128 TAP 160 192 224 256 0 32 64 96 128 TAP 160 192 224 256 Figure 2. Differential Non−Linearity, VDD = 5.6 V 120 100 VDD = 2.6 V 80 Rw (W) 60 3.3 V 40 20 0 4.0 V 0 50 100 TAP 5.6 V Vw (V) 4 3 2 1 0 6 Figure 3. Integral Non−Linearity, VDD = 5.6 V 5.6 V 5 5.0 V 4.0 V 3.3 V VDD = 2.6 V 150 200 250 0 52 104 TAP 156 208 260 Figure 4. Wiper Resistance at Room Temperature 400 350 300 ISB (nA) Figure 5. Wiper Voltage T = 90°C T = −45°C 250 200 150 100 T = 25°C 2 3 4 VDD (V) 5 6 Figure 6. Standby Current http://onsemi.com 5 CAT5171 TYPICAL CHARACTERISTICS 0.4 102.15 102.10 102.05 0.2 R (kW) 0 −0.2 −50 −20 10 40 70 100 D (%) 102.00 101.95 101.90 101.85 101.80 101.75 −50 −20 10 40 70 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 7. Change in End−to−End Resistance Figure 8. End−to−End Resistance vs. Temperature 30 25 0 −6 VDD = 5 V PSRR (dB) −12 A (dB) −18 −24 −30 −36 VDD = 3 V 20 VDD = 5 V 15 10 5 0 VDD = 3 V 1 10 f (KHz) 100 1000 1 10 f (KHz) 100 1000 Figure 9. Gain vs. Bandwidth (Tap 0x80) Figure 10. PSRR http://onsemi.com 6 CAT5171 Basic Operation The CAT5171 is a 256−position digitally controlled potentiometer. When power is first applied, the wiper assumes a mid−scale position. Once the power supply is stable, the wiper may be repositioned via the I2C compatible interface. Programming: Variable Resistor Rheostat Mode The equation for determining the digitally programmed output resistance between W and B is R WB + D R AB ) R W 256 (eq. 1) The resistance between terminals A and B, RAB, has a nominal value of 50 kW or 100 kW and has 256 contact points accessed by the wiper terminal, plus the B terminal contact. Data in the 8−bit Wiper register is decoded to select one of these 256 possible settings. The wiper’s first connection is at the B terminal, corresponding to control position 0x00. Ideally this would present a 0 W between the Wiper and B, but just as with a mechanical rheostat there is a small amount of contact resistance to be considered, there is a wiper resistance comprised of the RON of the FET switch connecting the wiper output with its respective contact point. In CAT5171 this ‘contact’ resistance is typically 50 W. Thus a connection setting of 0x00 yields a minimum resistance of 50 W between terminals W and B. For a 100 kW device, the second connection, or the first tap point, corresponds to 441 W (RWB = RAB/256 + RW = 390.6 + 50 W) for data 0x01. The third connection is the next tap point, is 831 W (2 x 390.6 + 50 W) for data 0x02, and so on. Figure 11 shows a simplified equivalent circuit where the last resistor string will not be accessed; therefore, there is 1 LSB less of the nominal resistance at full scale in addition to the wiper resistance. A RS where D is the decimal equivalent of the binary code loaded in the 8−bit Wiper register, RAB is the end−to−end resistance, and RW is the wiper resistance contributed by the on resistance of the internal switch. In summary, if RAB = 100 kW and the A terminal is open circuited, the following output resistance RWB will be set for the indicated Wiper register codes: Table 9. CODES AND CORRESPONDING RWB RESISTANCE FOR RAB = 100 kW, VDD = 5 V D (Dec.) 255 128 1 0 RWB (W) 99,559 50,050 441 50 Midscale 1 LSB Zero Scale (Wiper Contact Resistance) Output State Full Scale (RAB – 1 LSB + RW) Be aware that in the zero−scale position, the wiper resistance of 50 W is still present. Current flow between W and B in this condition should be limited to a maximum pulsed current of no more than 20 mA. Failure to heed this restriction can cause degradation or possible destruction of the internal switch contact. Similar to the mechanical potentiometer, the resistance of the DPP (Digitally Programmed Potentiometer) between the wiper W and terminal A also produces a digitally controlled complementary resistance RWA. When these terminals are used, the B terminal can be opened. Setting the resistance value for RWA starts at a maximum value of resistance and decreases as the data loaded in the latch increases in value. The general equation for this operation is R WA(D) + 256 * D R AB ) R W 256 (eq. 2) RS Wiper Register and Decoder RS W For RAB = 100 kW and the B terminal open circuited, the following output resistance RWA will be set for the indicated Wiper register codes. Table 10. CODES AND CORRESPONDING RWA RESISTANCE FOR RAB = 100 kW, VDD = 5 V D (Dec.) 255 RWA (W) 441 50,050 99,659 100,050 Full Scale Midscale 1 LSB Zero Scale Output State RS B 128 1 Figure 11. CAT5171 Equivalent DPP Circuit 0 Typical device to device resistance matching is lot dependent and may vary by up to ±20%. http://onsemi.com 7 CAT5171 ESD Protection Digital Input LOGIC Power−up Sequence GND Because ESD protection diodes limit the voltage compliance at terminals A, B, and W (see Figure 12), it is recommended that VDD/GND be powered before applying any voltage to terminals A, B, and W. The ideal power−up sequence is: GND, VDD, digital inputs, and then VA/B/W. The order of powering VA, VB, VW, and the digital inputs is not important as long as they are powered after VDD/GND. Power Supply Bypassing W, A, B Potentiometer GND Good design practice employs compact, minimum lead length layout design. Leads should be as direct as possible. It is also recommended to bypass the power supplies with quality low ESR Ceramic chip capacitors of 0.01 mF to 0.1 mF. Low ESR 1 mF to 10 mF tantalum or electrolytic capacitors can also be applied at the supplies to suppress transient disturbances and low frequency ripple. As a further precaution digital ground should be joined remotely to the analog ground at one point to minimize the ground bounce. VDD C3 10 mF + C1 0.1 mF VDD CAT5171 GND Figure 12. ESD Protection Networks Terminal Voltage Operating Range The CAT5171 VDD and GND power supply define the limits for proper 3−terminal digital potentiometer operation. Signals or potentials applied to terminals A, B or the wiper must remain inside the span of VDD and GND. Signals which attempt to go outside these boundaries will be clamped by the internal forward biased diodes. VDD Figure 14. Power Supply Bypassing W, A, B CAT5171 LOGIC GND Figure 13. http://onsemi.com 8 CAT5171 I2C Bus Protocol The following defines the features of the I2C bus protocol: 1. Data transfer may be initiated only when the bus is not busy. 2. During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock is high will be interpreted as a START or STOP condition. The device controlling the transfer is a master, typically a processor or controller, and the device being controlled is the slave. The master will always initiate data transfers and provide the clock for both transmit and receive operations. Therefore, the CAT5171 will be considered a slave device in all applications. addressed by the system. Typically, +5 V (VDD) or ground is hard−wired to the AD0 pin to establish the device’s address. After the Master sends a START condition and the slave address byte, the CAT5171 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave address. Acknowledge START Condition The START condition precedes all commands to the device, and is defined as a high to low transition of SDA when SCL is high. The CAT5171 monitors the SDA and SCL lines and will not respond until this condition is met. STOP Condition A low to high transition of SDA when SCL is high determines the STOP condition. All operations must end with a STOP condition. Device Addressing After a successful data transfer, each receiving device is required to generate an acknowledge. The Acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. The CAT5171 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8−bit byte. When the CAT5171 is in a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT5171 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. Write Operation In the Write mode, the Master device sends the START condition and the slave address information to the Slave device. After the Slave generates an acknowledge, the Master sends the instruction byte. After receiving another acknowledge from the Slave, the Master device transmits the data to be written into the wiper register. The CAT5171 acknowledges once more and the Master generates the STOP condition. tR tLOW The bus Master begins a transmission by sending a START condition. The Master then sends the address of the particular slave device it is requesting. The six most significant bits of the 8−bit slave address are fixed as 010110 for the CAT5171. The next bit (AD0) is the device least significant address bit and defines which device the Master is accessing. Up to two devices may be individually tF tLOW SCL tSU:STA SDA IN tAA SDA OUT tHD:STA tHD:DAT tHIGH tSU:DAT tSU:STO tDH tBUF Figure 15. Bus Timing Diagram http://onsemi.com 9 CAT5171 SDA SCL START CONDITION Figure 16. Start/Stop Condition STOP CONDITION SCL FROM MASTER 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START Figure 17. Acknowledge Condition ACKNOWLEDGE http://onsemi.com 10 CAT5171 INSTRUCTION AND REGISTER DESCRIPTION SLAVE ADDRESS BYTE power−up, the wiper is set to midscale and may be repositioned anytime after the power has become stable. INSTRUCTIONS The first byte sent to the CAT5171 from the master/processor is called the Slave Address Byte. The most significant six bits of the slave address are a device type identifier. For the CAT5171, these bits are fixed at 010110. The next bit, AD0, is the first bit of the internal slave address and must match the physical device address which is defined by the state of the AD0 input pin for the CAT5171 to successfully continue the command sequence. Only the device which slave address matches the incoming device address sent by the master executes the instruction. The AD0 input can be actively driven by CMOS input signals or tied to the supply voltage or ground. The next bit, R/W, indicates whether this command corresponds to a Write or Read instruction. To write into the Wiper control register, R/W bit is set to a logic low; while a read from the wiper register is done with the bit high. WIPER CONTROL Write and Read instructions are respectively three and two bytes in length. The basic sequence of the two instructions is illustrated in Table 11 and 12. In write mode, the second byte is the instruction byte. The first bit (MSB) of the instruction byte is a don’t care. The second MSB, RS, is the midscale reset. A logic high on this bit moves the wiper to the center tap. The third MSB, SD, is a shutdown bit. A logic high causes an open circuit at terminal A, and short the wiper terminal W to terminal B. The “shutdown” operation does not change the contents of the wiper register. When the shutdown bit, SD, goes back to a logic low, the previous wiper position is restored. Also during shutdown, new settings can be programmed. As soon as the device is returned from shutdown, the wiper position is set according to the wiper register value. TWO CAT5171 ON A SINGLE BUS The CAT5171 contains one 8−bit Wiper Control Register (WCR). The Wiper Control Register output is decoded to select one of 256 switches along its resistor array. The contents of the WCR may be written by the host via Write instruction. The Wiper Control Register is a volatile register that loses its contents when the CAT5171 is powered−down. Upon Table 11. Write S 0 1 0 1 1 0 AD0 W A X RS SD X X X When needed, it is possible to connect two CAT5171 potentiometers on the same I2C bus and be able to address each one independently. Each device can be set to a unique address by using the AD0 input pin. One device AD0 pin is connected to ground, and the other device AD0 pin is tied to the supply voltage. X X A D7 D6 D5 D4 D3 D2 D1 D0 A P Slave Address Byte SDA 01 S T A R T 0 11 0 AD0 R/W A C K Slave Address Byte X RS Instruction Byte Data Byte SD XXXXX A C K D7 D6 D5 D4 D3 D2 D1 D0 AS CT KO P Instruction Byte Data Byte Table 12. READ S 0 1 0 1 1 0 AD0 R A D7 D6 D5 D4 D3 D2 D1 D0 A P Slave Address Byte SDA S T A R T 0 10 11 0 AD0 R/W A C K Slave Address Byte D7 D6 D5 Data Byte D4 D3 D2 D1 D0 N A C K S T O P Data Byte Legend S = Start P = Stop A = Acknowledge AD0 = Address bit 0, needed when using two potentiometers on the same I2C bus. D = Data bit R = Read (bit is 1 for Read instruction) W = Write (bit is 0 for Write instruction) RS = When the bit is 1, the wiper position is moved to mid−scale 0x80 SD = Shut Down: 0: normal operation 1: wiper is parked at B terminal and terminal A is open circuit. X = Don’t Care http://onsemi.com 11 CAT5171 PACKAGE DIMENSIONS SOT−23, 8 Lead CASE 527AK−01 ISSUE A SYMBOL A A1 A2 E1 E A3 b c D E e PIN #1 IDENTIFICATION TOP VIEW b E1 e L L1 L2 MIN 0.90 0.00 0.90 0.60 0.28 0.08 NOM MAX 1.45 0.15 1.10 1.30 0.80 0.38 0.22 2.90 BSC 2.80 BSC 1.60 BSC 0.65 BSC 0.30 0.45 0.60 REF 0.25 REF 0.60 θ 0° 8° D A A2 A3 q c A1 SIDE VIEW Notes: (1) All dimensions in millimeters. Angles in degrees. (2) Complies with JEDEC standard MO-178. L1 L L2 END VIEW ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone : 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative http://onsemi.com 12 CAT5171/D