CAT64LC40WI

CAT64LC40 4K-Bit SPI Serial EEPROM FEATURES DESCRIPTION ■ SPI bus compatible The CAT64LC40 is a 4K-bit Serial EEPROM which is configured as 256 registers by 16 bits. Each register can be written (or read) serially by using the DI (or DO) pin. The CAT64LC40 is manufactured using Catalyst’s advanced CMOS EEPROM floating gate technology. It is designed to endure 1,000,000 program/erase cycles and has a data retention of 100 years. The device is available in 8-pin DIP, SOIC and TSSOP packages. ■ Low power CMOS technology ■ 2.5V to 6.0V operation ■ Self-timed write cycle with auto-clear ■ Hardware reset pin ■ Hardware and software write protection ■ Commercial, industrial and automotive temperature ranges ■ Power-up inadvertant write protection BSY pin for end-of-write indication ■ RDY/BSY ■ 1,000,000 program/erase cycles ■ 100 year data retention PIN CONFIGURATION SOIC Package (J, W) DIP Package (P, L) CS SK DI DO 1 2 3 4 8 7 6 5 VCC RDY/BUSY RESET GND RDY/BUSY VCC CS SK 1 2 3 4 8 7 6 5 TSSOP Package (U, Y) CS SK DI DO RESET GND DO DI SOIC Package (S, V) CS SK DI DO 1 2 3 4 8 7 6 5 8 7 6 5 VCC RDY/BUSY RESET GND TSSOP Package (UR, YR) VCC RDY/BUSY RESET GND PIN FUNCTIONS 1 2 3 4 1 2 3 4 RDY/BUSY VCC CS SK 8 7 6 5 RESET GND DO DI BLOCK DIAGRAM Pin Name Function CS Chip Select SK Clock Input DI Serial Data Input DO Serial Data Output VCC +2.5V to +6.0V Power Supply GND Ground RESET Reset RDY/BUSY Ready/BUSY Status © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. VCC GND MEMORY ARRAY 256 x 16 ADDRESS DECODER DATA REGISTER OUTPUT BUFFER DI RESET CS SK 1 MODE DECODE LOGIC CLOCK GENERATOR DO RDY/BUSY Doc. No. MD-1021, Rev. E CAT64LC40 ABSOLUTE MAXIMUM RATINGS* *COMMENT Temperature Under Bias ................. –55°C to +125°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Storage Temperature ....................... –65°C to +150°C Voltage on any Pin with Respect to Ground(1) ............ –2.0V to +VCC +2.0V VCC with Respect to Ground ............... –2.0V to +7.0V Package Power Dissipation Capability (Ta = 25°C) ................................... 1.0W Lead Soldering Temperature (10 secs) ............ 300°C Output Short Circuit Current(2) ........................ 100 mA RELIABILITY CHARACTERISTICS Symbol NEND (3) Parameter Endurance Min. Max. Units 1,000,000 Cycles/Byte TDR(3) Data Retention 100 Years VZAP(3) ESD Susceptibility 2000 Volts ILTH(3)(4) Latch-Up 100 mA CAPACITANCE (TA = 25°C, f= 1.0 MHz, VCC =6.0V) Symbol CI/O(3) CIN (3) Test Max. Conditions Units Input/Output Capacitance (DO, RDY/BSY) 8 VI/O = 0V pF Input Capacitance (CS, SK, DI, RESET) 6 VIN = 0V pF Note: (1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns. (2) Output shorted for no more than one second. No more than one output shorted at a time. (3) This parameter is tested initially and after a design or process change that affects the parameter. (4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to VCC +1V. Doc. No. MD-1021, Rev. E 2 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT64LC40 D.C. OPERATING CHARACTERISTICS VCC = +2.5V to +6.0V, unless otherwise specified. Limits Sym. ICC ICCP Parameter Test Conditions Units 0.4 fSK = 250 kHz mA EWEN, EWDS, READ 6.0V 1 fSK = 1 MHz mA Program Current 2.5V 2 mA 6.0V 3 mA Operating Current Min. Typ. 2.5V Max. ISB(1) Standby Current 3 VIN = GND or VCC CS = VCC µA ILI Input Leakage Current 2 VIN = GND to VCC µA ILO Output Leakage Current 10 VOUT = GND to VCc µA VIL Low Level Input Voltage, DI –0.1 VCC x 0.3 V VIH High Level Input Voltage, DI VCC x 0.7 VCC + 0.5 V VIL Low Level Input Voltage, CS, SK, RESET –0.1 VCC x 0.2 V VIH High Level Input Voltage, CS, SK, RESET VCC x 0.8 VCC + 0.5 V VOH(1) High Level Output Voltage VOL(1) Low Level Output Voltage 2.5V VCC – 0.3 IOH = –10µA V 6.0V VCC – 0.3 IOH = –10µA V 2.4 IOH = –400µA V 2.5V 0.4 IOL = 10µA V 6.0V 0.4 IOL = 2.1mA V Note: (1) VOH and VOL spec applies to READY/BUSY pin also © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 3 Doc. No. MD-1021, Rev. E CAT64LC40 A.C. OPERATING CHARACTERISTICS VCC = +2.5V to +6.0V, unless otherwise specified. Limits Symbol Parameter Min. Typ. Max. Units tCSS CS Setup Time 100 ns tCSH CS Hold Time 100 ns tDIS DI Setup Time 200 ns tDIH DI Hold Time 200 ns tPD1 Output Delay to 1 300 ns tPD0 Output Delay to 0 300 ns tHZ(2) Output Delay to High Impendance 500 ns tCSMIN Minimum CS High Time tSKHI Minimum SK High Time tSKLOW Minimum SK Low Time tSV Output Delay to Status Valid fSK Maximum Clock Frequency tRESS Reset to CS Setup Time tRESMIN 250 ns 2.5V 1000 ns 4.5V–6.0V 400 2.5V 1000 4.5V–6.0V 400 ns 500 2.5V 250 4.5V–6.0V 1000 ns kHz 0 ns Minimum RESET High Time 250 ns tRESH RESET to READY Hold Time 0 ns tRC Write Recovery 100 ns POWER-UP TIMING(1)(3) Symbol Parameter Min. Max. Units tPUR Power-Up to Read Operation 10 µs tPUW Power-Up to Program Operation 1 ms Max. Units 2.5V 10 ms 4.5V–6.0V 5 WRITE CYCLE LIMIITS Symbol tWR Parameter Min. Program Cycle Time Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) This parameter is sampled but not 100% tested. (3) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. Doc. No. MD-1021, Rev. E 4 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT64LC40 INSTRUCTION SET Instruction Opcode Address Data Read 10101000 A7 A6 A5 A4 A3 A2 A1 A0 D15 - D0 Write 10100100 A7 A6 A5 A4 A3 A2 A1 A0 D15 - D0 Write Enable 10100011 XXXXXXXX Write Disable 10100000 XXXXXXXX [Write All Locations](1) 10100001 XXXXXXXX D15–D0 Figure 1. A.C. Testing Input/Output Waveform (2)(3)(4) (CL = 100 pF) VCC x 0.8 VCC x 0.7 INPUT PULSE LEVELS VCC x 0.2 REFERENCE POINTS VCC x 0.3 Note: (1) (Write All Locations) is a test mode operation and is therefore not included in the A.C./D.C. Operations specifications. (2) Input Rise and Fall Times (10% to 90%) < 10 ns. (3) Input Pulse Levels = VCC x 0.2 and VCC x 0.8. (4) Input and Output Timing Reference = VCC x 0.3 and VCC x 0.7. © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 5 Doc. No. MD-1021, Rev. E CAT64LC40 DEVICE OPERATION data to be written are clocked into the DI pin on the rising edge of the SK clock. The DO pin is normally in a high impedance state except when outputting data in a READ operation or outputting RDY/BSY status when polled during a WRITE operation. The CAT64LC40 is a 4K-bit nonvolatile memory intended for use with all standard controllers. The CAT64LC40 is organized in a 256 x 16 format. All instructions are based on an 8-bit format. There are four 16-bit instructions: READ, WRITE, EWEN, and EWDS. The CAT64LC40 operates on a single power supply ranging from 2.5V to 6.0V and it has an on-chip voltage generator to provide the high voltage needed during a programming operation. Instructions, addresses and The format for all instructions sent to this device includes a 4-bit start sequence, 1010, a 4-bit op code and an 8bit address field or dummy bits. For a WRITE operation, Figure 2. Sychronous Data Timing RESET tSKLOW tRESS tSKHI SK tDIS tDIH DI tCSH tCSS tCSMIN CS tPD0,tPD1 tHZ tSV DO tRESH tRC tSV RDY/BUSY Figure 3. Read Instruction Timing RESET SK CS DI 1 0 1 0 1 0 0 0 ADDRESS* DO D15 D14 D1 D0 HIGH RDY/BUSY * Please check the instruction set table for address Doc. No. MD-1021, Rev. E 6 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT64LC40 a 16-bit data field is also required following the 8-bit address field. Read Upon receiving a READ command and address (clocked into the DI pin), the DO pin will output data one tPD after the falling edge of the 16th clock (the last bit of the address field). The READ operation is not affected by the RESET input. The CAT64LC40 requires an active LOW CS in order to be selected. Each instruction must be preceded by a HIGH-to-LOW transition of CS before the input of the 4bit start sequence. Prior to the 4-bit start sequence (1010), the device will ignore inputs of all other logical sequence. Write After receiving a WRITE op code, address and data, the device goes into the AUTO-Clear cycle and then the Figure 4. Write Instruction Timing RESET SK CS DI 1 0 1 0 0 1 0 0 ADDRESS* D15 D0 DO RDY/BUSY * Please check instruction set table for address Figure 5. Ready/BUSY BUSY Status Instruction Timing RESET LOW SK CS WRITE INSTRUCTION NEXT INSTRUCTION DI DO HIGH RDY/BUSY © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 7 Doc. No. MD-1021, Rev. E CAT64LC40 WRITE cycle. The RDY/BSY pin will output the BUSY status (LOW) one tSV after the rising edge of the 32nd clock (the last data bit) and will stay LOW until the write cycle is complete. Then it will output a logical “1” until the next WRITE cycle. The RDY/BSY output is not affected by the input of CS. the device is deselected. The rising edge of the first “1” input on the DI pin will reset DO back to the high impedance state again. The WRITE operation can be halted anywhere in the operation by the RESET input. If a RESET pulse occurs during a WRITE operation, the device will abort the operation and output a READY status. An alternative to get RDY/BSY status is from the DO pin. During a write cycle, asserting a LOW input to the CS pin will cause the DO pin to output the RDY/BSY status. Bringing CS HIGH will bring the DO pin back to a high impedance state again. After the device has completed a WRITE cycle, the DO pin will output a logical “1” when NOTE: Data may be corrupted if a RESET occurs while the device is BUSY. If the reset occurs before the BUSY period, no writing will be initiated. However, if RESET occurs after the BUSY period, new data will have been written over the old data. Figure 6. RESET During BUSY Instruction Timing RESET SK CS DI 1 0 1 0 0 1 0 0 ADDRESS* D15 D0 DO tWR RDY/BUSY * Please check instruction set table for address Figure 7. EWEN Instruction Timing RESET SK CS DI DO RDY/BUSY 1 0 1 0 0 0 1 1 HIGH-Z HIGH 5064 FHD F09 Doc. No. MD-1021, Rev. E 8 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT64LC40 RESET ERASE/WRITE ENABLE and DISABLE The RESET pin, when set to HIGH, will reset or abort a WRITE operation. When RESET is set to HIGH while the WRITE instruction is being entered, the device will not execute the WRITE instruction and will keep DO in HighZ condition. The CAT64LC40 powers up in the erase/write disabled state. After power-up or while the device is in an erase/ write disabled state, any write operation must be preceded by an execution of the EWEN instruction. Once enabled, the device will stay enabled until an EWDS has been executed or a power-down has occured. The EWDS is used to prevent any inadvertent over-writing of the data. The EWEN and EWDS instructions have no affect on the READ operation and are not affected by the RESET input. When RESET is set to HIGH, while the device is in a clear/write cycle, the device will abort the operation and will display READY status on the RDY/BSY pin and on the DO pin if CS is low. The RESET input affects only the WRITE and WRITE ALL operations. It does not reset any other operations such as READ, EWEN and EWDS. Figure 8. EWDS Instruction Timing RESET SK CS DI 1 0 1 DO 0 0 0 0 0 HIGH-Z HIGH RDY/BUSY © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 9 Doc. No. MD-1021, Rev. E CAT64LC40 ORDERING INFORMATION 64LC40 P: PDIP S: SOIC (JEDEC) J: SOIC (JEDEC) U: TSSOP UR: TSSOP (Rotated) L: PDIP (Lead free, Halogen free) V: SOIC (JEDEC) (Lead free, Halogen free) W: SOIC (JEDEC) (Lead free, Halogen free) Y: TSSOP (Lead free, Halogen free) YR: TSSOP (Rotated) (Lead free, Halogen free) Notes: (1) The device used in the above example is a 64LC40SI-TE13 (SOIC, Industrial Temperature, Tape & Reel) Doc. No. MD-1021, Rev. E 10 © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. CAT64LC40 PACKAGING OUTLINE DRAWING TSSOP 8-Lead (U) b SYMBOL MIN NOM A E1 E MAX 1.20 A1 0.05 A2 0.80 b 0.19 0.30 c 0.09 0.20 D 2.90 3.00 3.10 E 6.30 6.40 6.50 E1 4.30 4.40 4.50 e 0.15 0.90 1.05 0.65 BSC L 1.00 REF L1 0.50 θ1 0° 0.60 0.75 8° e TOP VIEW D A2 A A1 c θ1 L1 L END VIEW SIDE VIEW For current Tape and Reel information, download the PDF file from: http://www.catsemi.com/documents/tapeandreel.pdf. Notes: 1. All dimensions are in millimeters. Angles in degrees. 2. Complies with JEDEC standard MO-153. © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice. 11 Doc. No. MD-1021, Rev. E CAT64LC40 REVISION HISTORY Date Revision Description 3-Sep-04 B Added Green packages in all areas Updated DC Operating Characteristics table & notes 17-Nov-04 C Changed ISB from 1µA, Max to 3µA, Max in DC Operating Characteristics table 21-May-06 D Discontinued the CAT64LC10 and CATLC205 11-Nov-08 E Update Package Outline Drawing Change logo and fine print to ON Semicondctor ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com Doc. No. MD-1021, Rev. E N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center: Phone: 81-3-5773-3850 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative © 2008 SCILLC. All rights reserved. Characteristics subject to change without notice.