CM1218-C4SE

Low Capacitance Transient Voltage Suppressors / ESD Protectors CM1218-C4 Features • • • Low I/O capacitance at 7pF typical Four channels of ESD protection In-system ESD protection to ±15kV contact discharge, per the IEC 61000-4-2 international standard Compact SMT package saves board space and facilitates layout in space-critical applications Each I/O pin can withstand over 1000 ESD strikes RoHS-compliant, lead-free For other versions of the CM1218, see the CM1218 datasheet or the CM1218-H4 datasheet. Product Description The CM1218-C4 device features transient voltage suppressor arrays that provide a very high level of protection for sensitive electronic components which may be subjected to electrostatic discharge (ESD). All pins of the CM1218-C4 are rated to withstand ±15kV ESD pulses using the IEC 61000-4-2 contact discharge method. Using the MIL-STD-883D (Method 3015) specification for Human Body Model (HBM) ESD, all pins are protected from contact discharges of greater than ±30kV. The CM1218C4 is supplied in an SOT-553, RoHScompliant, lead-free finished package. • • • Note: Applications • • High-speed consumer electronic ports ESD protection of PC ports, including USB ports, serial ports, parallel ports, IEEE1394 ports, docking ports, proprietary ports, etc. Protection of interface ports or IC pins which are exposed to high ESD levels • Block Diagram ©2010 SCILLC. All rights reserved. April 2010 – Rev. 2 Publication Order Number: CM1218-C4/D CM1218-C4 Pin Configurations Pin Information PIN DESCRIPTIONS LEADS (Refer to package / pinout diagrams) NAME CHx DESCRIPTION The cathode of the respective TVS diode, which should be connected to the node requiring transient voltage protection. The anode of the TVS diodes. (Refer to package / pinout diagrams) VN Ordering Information PART NUMBERING INFORMATION Lead-free Finish Leads 5 Channels 4 Package SOT-553 Ordering Part Number CM1218-C4SE Part Marking R4C Notes : The maximum soldering reflow temperature for these packages is 260° Parts are shipped in tape and reel form unless C. otherwise specified. Rev. 2 | Page 2 of 7 | www.onsemi.com CM1218-C4 Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER Storage Temperature Range Package Power Dissipation SOT-553 RATING –65 to +150 UNITS ° C 0.15 W STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature RATING –40 to +85 UNITS ° C ELECTRICAL OPERATING CHARACTERISTICS SYMBOL PARAMETER CIN Channel Input Capacitance Differential Channel I/O to GND Capacitance Reverse Stand-off Voltage CONDITIONS TA = 25° 2.5VDC, 1MHz C, TA = 25° 2.5VDC, 1MHz C, IR = 10µA, TA = 25° C IR = 1mA, TA = 25° C ILEAK VSIG Leakage Current Small Signal Clamp Voltage Positive Clamp Negative Clamp ESD Withstand Voltage Contact Discharge per IEC 610004-2 standard Human Body Model, MIL-STD-883, Method 3015 Diode Dynamic Resistance Forward Conduction Reverse Conduction VIN = 5.0VDC, TA = 25° C 5.5 6.1 1 MIN TYP 7 0.19 MAX UNITS pF pF V V ∆C IN VRSO µA V V kV kV I = 10mA, TA = 25° C I = –10mA, TA = 25° C Notes 2 and 3; TA = 25° C Notes 1 and 3; TA = 25° C TA = 25° Note 1 C; +15 +30 6.8 -0.8 VESD RD 0.57 1.36 Ω Ω Note 1: Human Body Model per MIL-STD-883, Method 3015, CDischarge = 100pF, RDischarge = 1.5KΩ, VN grounded. Note 2: Standard IEC 61000-4-2 with CDischarge = 150pF, RDischarge = 330Ω, VN grounded. Note 3: These measurements performed with no external capacitor on CHX. Rev. 2 | Page 3 of 7 | www.onsemi.com CM1218-C4 Performance Information Diode Capacitance Typical diode capacitance with respect to positive TVS cathode voltage (reverse voltage across the diode) is given in Diode Capacitance vs. Reverse Voltage . Figure 1. Diode Capacitance vs. Reverse Voltage Typical High Current Diode Characteristics Measurements are made in pulsed mode with a nominal pulse width of 0.7ms. Rev. 2 | Page 4 of 7 | www.onsemi.com CM1218-C4 Mechanical Details SOT-553 Mechanical Specifications The CM1218-C4SE is supplied in a 5-pin SOT-553 package. Dimensions are presented below. PACKAGE DIMENSIONS Package Leads Dim. Min A b c D E E1 e e1 L # per tape and reel 0.50 0.17 0.08 Millimeters Nom 0.55 0.22 0.13 1.60 BSC 1.60 BSC 1.20 BSC 0.50 BSC 1.00 BSC 0.20 BSC 5000 pieces Max 0.60 0.27 0.18 Min 0.020 0.007 0.003 SOT-553 5 Inches Nom 0.022 0.009 0.005 Max 0.024 0.011 0.007 0.063 BSC 0.063 BSC 0.047 BSC 0.020 BSC 0.040 BSC 0.008 BSC Controlling dimension: millimeters Package Dimensions for SOT-553 Rev. 2 | Page 5 of 7 | www.onsemi.com CM1218-C4 Tape and Reel Specifications PACKAGE SIZE PART NUMBER (mm) CM1218-C4SE 1.60 X 1.60 X 0.55 POCKET SIZE (mm) B0 X A0 X K0 1.78 X 1.78 X 0.690 TAPE WIDTH REEL W DIAMETER 8mm 178mm (7") QTY PER REEL 5000 P0 4mm P1 4mm Rev. 2 | Page 6 of 7 | www.onsemi.com CM1218-C4 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 For additional information, please contact your local Sales Representative Order Literature: http://www.onsemi.com/orderlit ON Semiconductor Website: www.onsemi.com Rev. 2 | Page 7 of 7 | www.onsemi.com