CM1683

Praetorian® L-C EMI Filter with ESD Protectionfor Headsets/Speakers CM1683 Features • • • • • • Two channels of EMI filtering ±8kV ESD protection (IEC 61000-4-2, contact discharge) ±15kV ESD protection (HBM) Greater than -40dB of attenuation at 1GHz 8-lead, 2.00mm x 2.00mm, 0.5mm pitch uDFN package RoHS-compliant, lead-free finishing Product Description The CM1683 is an L-C EMI filter array with ESD protection, which integrates two Pi-filters (C-L-C) for the headset speaker. The CM1683 has component values of 100pF-3nH-100pF. The parts include ESD protection diodes on all input/output pins, which provide a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The ESD diodes connected to the filter ports safely dissipate ESD strikes of ±8kV, beyond the maximum requirement of the IEC61000-4-2 international standard. Using the MIL-STD-883 (Method 3015) specification for Human Body Model (HBM) ESD, the pins are protected for contact discharges at greater than ±15kV. This device is particularly well suited for portable electronics (e.g. mobile handsets, PDAs, notebook computers) because of its small package format and easy-to-use pin assignments. In particular, the CM1683 is ideal for EMI filtering and protecting speaker output lines from ESD for the headset speaker in mobile handsets. Most speakers have impedance of 8Ω and in order to maximize the power output, the resistance of an EMI filter needs to be as low as possible and the CM1683 addresses this by having a C-L-C based EMI filter where the inductor has less than 1Ω of resistance. Applications • • • Headset Speaker port in mobile handsets I/O port protection for mobile handsets, notebook computers, PDAs, etc. EMI filtering for data ports in cell phones, PDAs or notebook computers ©2010 SCILLC. All rights reserved. May 2010 – Rev. 2 Publication Order Number: CM1683/D CM1683 Electrical Schematic 8765 Note:This drawing is not to scale. Rev. 2 | Page 2 of 8 | www.onsemi.com CM1683 PIN DESCRIPTIONS PIN 1 2 3 4 5 6 7 8 DAP NAME Filter #1 NC NC Filter #2 Filter #2 NC NC Filter #1 GND DESCRIPTION Filter #1 No connect No connect Filter #2 Filter #2 No connect No connect Filter #1 Ground Ordering Information PART NUMBERING INFORMATION Lead-free Finish Pins 8 Package uDFN Ordering Part Number1 CM1683-02DE Part Marking P83 Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Rev. 2 | Page 3 of 8 | www.onsemi.com CM1683 Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER Storage Temperature Range DC current per inductor DC package power rating RATING –65 to +150 30 0.5 UNITS °C mA W STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range RATING –40 to +85 UNITS °C Rev. 2 | Page 4 of 8 | www.onsemi.com CM1683 ELECTRICAL OPERATING CHARACTERISTICS (NOTE 1) SYMBOL PARAMETER L R CTOT C ILEAK Inductance DC Channel Resistance Total Channel Capacitance Capacitance C Diode Leakage Current 2.5V DC; 1MHz, 30mV AC 2.5V DC; 1MHz, 30mV AC VIN = +5V VIN =-5V VSIG Signal Clamp Voltage Positive Clamp Negative Clamp In-system ESD Withstand Voltage Human Body Model, MIL-STD-883, Method 3015 Contact Discharge per IEC 610004-2 Level 4 Cut-off frequency Z = 50Ω , Z SOURCE CONDITIONS MIN TYP 3.0 0.75 MAX UNITS nH 1 240 Ω pF pF 160 200 100 0.1 1.0 μA μA -1.0 -0.1 ILOAD = 10mA ILOAD = –10mA Note 2 5 –15 7 –10 15 –5 V V VESD ±15 ±8 kV kV fC = 50Ω LOAD L = 3nH, C = 100pF 31 MHz Note 1: TA = 25°C unless otherwise specified. Note 2: ESD applied to input and output pins with respect to GND, one at a time. Rev. 2 | Page 5 of 8 | www.onsemi.com CM1683 Performance Information Typical Filter Performance (nominal conditions unless specified otherwise, 50 ohm environment) Figure 1. Insertion Loss vs. Frequency (Filter #1 to GND) Figure 2. Insertion Loss vs. Frequency (Filter #2 to GND) Rev. 2 | Page 6 of 8 | www.onsemi.com CM1683 Mechanical Details uDFN-08 Mechanical Specifications, 0.5mm Dimensions for the CM1683 supplied in a 2mmx2mm, 8-lead, 0.5mm pitch uDFN package are presented below. PACKAGE DIMENSIONS Package JEDEC No. Leads Millimeters Dim. Min A A1 A3 b D D2 E E2 e K L # per tape and reel 0.20 0.20 0.30 0.40 0.20 1.90 1.50 1.90 0.80 0.45 0.00 Nom 0.50 0.02 0.127 REF 0.25 2.00 1.60 2.00 0.90 0.50 BSC 0.30 2.10 1.70 2.10 1.00 Max 0.55 0.05 Min 0.018 0.000 Nom 0.020 0.001 Max 0.022 0.002 uDFN MO-229C 8 Inches 0.005 REF 0.008 0.075 0.059 0.075 0.031 0.010 0.079 0.063 0.079 0.035 0.012 0.083 0.067 0.083 0.039 0.020 BSC 0.008 0.008 0.012 0.016 3000 pieces Controlling dimension: millimeters Dimensions for 8-Lead, 0.5mm pitch uDFN package This package is compliant with JEDEC standard MO-229C with the exception of the "D", "D2", "E", "E2", "K" and "L" dimensions as called out in the table above. Rev. 2 | Page 7 of 8 | www.onsemi.com CM1683 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative Rev. 2 | Page 8 of 8 | www.onsemi.com