EGP10B

DATA SHEET www.onsemi.com Rectifier, High Efficiency, Glass Passivated, 1.0A EGP10B - EGP10K AXIAL LEAD / DO−41 CASE 017AH Features     Superfast Recovery Time for High Efficiency Low Forward Voltage, High Current Capability Low Leakage Current High Surge Current Capability MARKING DIAGRAM EGP10X ZYWW ABSOLUTE MAXIMUM RATINGS (TA = 25C unless otherwise noted) Value Unit Average Rectified Current 0.375” lead length @ TL = 75_C Parameter 1.0 A EGP10X Peak Forward Surge Current 8.3 ms single half−sine−wave Superimposed on rated load (JEDEC method) 30 A Z YWW PD Total Device Dissipation Derate above 25_C 2.5 17 W mWC IC Thermal Resistance, Junction to Ambient 50 C/W TJ, TSTG Junction and Storage Temperature Range −65~150 C Symbol IO If(surge) = Specific Device Code X = B/C/D/F/G/K = Assembly Code = Date Code (Year & Week) ORDERING INFORMATION See detailed ordering and shipping information on page 3 of this data sheet. Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. *These ratings are limiting values above which the serviceability of any semiconductor device may be impaired. ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Device 10B 10C 10D 10F 10G 10K Unit Peak Repetitive Reverse Voltage 100 150 200 300 400 800 V Maximum RMS Voltage 70 105 140 210 280 560 V DC Reverse Voltage (Rated VR) 100 150 200 300 400 800 V Parameter Maximum Reverse Current at Rated VR TA = 25_C 5.0 mA TA = 125_C 100 mA Maximum Reverse Recovery Time IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A Maximum Forward Voltage @ 2.0 A Typical Junction Capacitance VR = 4.0 V, f = 1.0 MHz 50 0.95 1.25 22 15 75 nS 1.7 V pF Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. *Pulse Test: Pulse Width  300 ms, Duty Cycle  2%.  Semiconductor Components Industries, LLC, 2007 October, 2022 − Rev. 2 1 Publication Order Number: EGP10K/D EGP10B − EGP10K TYPICAL PERFORMANCE CHARACTERISTICS 30 Peak Forward Surge Current (A) Forward Current (A) 1 0.75 Single Phase Half Wave 60 Hz Resistive or Inductive LOAD .375” (9.0 mm) LEAD Lengths 0.50 0.25 0 25 50 75 100 125 150 25 20 15 10 5 0 175 1 2 Ambient Temperature (5C) Reverse Current (mA) Forward Current (A) EGP10B−EGP10D TA = 25C 1 EGP10F−EGP10K Pulse Width = 30 ms 2% Duty Cycle 0.4 0.6 0.8 1.0 1.2 1.4 0.1 TA = 25C 0.01 1.6 1.8 Capacitance (pF) 20 40 60 80 100 Figure 4. Reverse Characteristics 40 EGP10B−EGP10D 20 EGP10F−EGP10K 10 0 120 Percent of Rated Peak Reverse Voltage (%) 50 1 TA = 100C 1 60 0 0.1 TA = 125C 10 Figure 3. Forward Characteristics 10 100 100 Forward Voltage (V) 30 50 1000 TA = 150C 0.01 0.2 20 Figure 2. Non−Repetitive Surge Current 50 0.1 10 Number of Cycles at 60 Hz Figure 1. Forward Current Derating Curve 10 5 100 1000 Reverse Voltage (V) Figure 5. Junction Capacitance www.onsemi.com 2 140 EGP10B − EGP10K Reverse Recovery Time Characteristic and Test Circuit Diagram 50 W Non−inductive trr 50 W Non−inductive DUT + 50 V − (approx.) 50 W Non−inductive +0.5 A (−) 0 Pulse Generator (Note 2) Oscilloscope (Note 1) −0.25 A (+) Notes: 1. Rise time = 7.0 ns max; Input impedance = 1.0 MW 22 pF. 2. Rise time = 10 ns max; Source impedance = 50 W. −1 A Figure 6. Test Circuit Diagram 1 cm Set Time Base for 5/10 ns/cm Figure 7. Reverse Recovery Time Characteristics ORDERING INFORMATION Device Package Shipping† EGP10B Axial Lead / DO−41 (Pb−Free) 5000 / Tape & Reel EGP10C EGP10D EGP10F EGP10G EGP10K †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 3 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS AXIAL LEAD / DO−41 CASE 017AH ISSUE O DATE 31 AUG 2016 25.40 MIN (2X) 5.20 4.06 0.86 0.71 NOTES: UNLESS OTHERWISE SPECIFIED 2.72 2.03 DOCUMENT NUMBER: DESCRIPTION: 98AON13444G AXIAL LEAD / DO−41 A) PACKAGE STANDARD REFERENCE: JEDEC DO−204 VARIATION AL. B) PACKAGE BODY CAN BE PLASTIC OR HERMETICALLY SEALED GLASS. C) ALL DIMENSIONS ARE IN MILLIMETERS. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative