EMI2124
Single Pair Common Mode
Filter with ESD Protection
Description
The EMI2124 is an integrated common mode filter providing both
ESD protection and EMI filtering for high speed serial digital
interfaces such as USB2.0.
The EMI2124 provides EMI filtering for one differential data line
pair and ESD protection for one data pair plus USB ID pin. It provides
a separate Vbus line protection typically used for charging. It is
supplied in a small RoHS-compliant WDFN8 package.
http://onsemi.com
SIMPLIFIED SCHEMATIC
Features
2
• Highly Integrated Common Mode Filter (CMF) with ESD Protection
•
•
•
•
•
•
•
provides protection and EMI Reduction for systems using high speed
Serial Data Lines with cost and space savings over Discrete Solutions
Large Differential Mode Bandwidth with Cutoff Frequency > 2 GHz
High Common Mode Stop Band Attenuation: >25 dB at 700 MHz,
>30 dB at 800 MHz Typical
Provides Data Lines ESD Protection to IEC61000-4-2 Level 4, ±12
kV Contact Discharge
Provides VID & VBUS ESD Protection to IEC61000-4-2 Level 4,
±30 kV Contact Discharge
Low Channel Input Capacitance provides Superior Impedance
Matching Performance
Low Profile Package with Small Footprint in WDFN8 2.0 mm length
x 2.2 mm width x 0.75 mm height Pb−Free Package
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
Internal
(ASIC)
8
External
(Connector)
1
7
5 (Vbus)
6
3,4
MARKING
DIAGRAM
8
WDFN8
CASE 511BN
1
1
C3 MG
G
C3 = Specific Device Code
M = Date Code
G
= Pb−Free Device
(Note: Microdot may be in either location)
Applications
PIN CONNECTIONS
• USB2.0 and other High Speed Differential Data Lines in Mobile
Phones and Digital Still Cameras
• MIPI D−PHY
In_1+
1
8
Out_1+
In_1−
2
7
Out_1−
GND
3
6
VID
GND
4
5
VBUS
GND
(Top View)
ORDERING INFORMATION
Device
EMI2124MTTAG
Package
Shipping†
WDFN8
(Pb−Free)
3000/Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2012
May, 2012 − Rev. 0
1
Publication Order Number:
EMI2124/D
EMI2124
PIN DESCRIPTION
Pin No.
Pin Name
Type
1
In_1+
I/O
CMF Channel 1+ to Connector (External)
2
In_1−
I/O
CMF Channel 1− to Connector (External)
8
Out_1+
I/O
CMF Channel 1+ to ASIC (Internal)
7
Out_1−
I/O
CMF Channel 1− to ASIC (Internal)
5
VBUS
I/O
Supply Protection to Connector − VBUS (External − VBUS)
Supply Protection to Connector (External − VID)
6
ID
I/O
3,4
GND
GND
Description
Ground
MAXIMUM RATINGS (TA = 25°C unless otherwise stated)
Parameter
Symbol
Value
Units
Operating Temperature Range
TOP
−40 to +85
°C
Storage Temperature Range
TSTG
−65 to +150
°C
TL
260
°C
ILINE
100
mA
Maximum Lead Temperature for Soldering Purposes (1/8” from Case for 10 Seconds)
DC Current per Line
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
2
EMI2124
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified)
Parameter
Symbol
Test Conditions
Channel Leakage Current
ILEAK
Channel Negative Voltage
VF
TA = 25°C, IF = 10 mA
Channel Input Capacitance to ground
(Pins 1,2,8,7 to GND)
CIN
TA = 25°C, At 1 MHz, GND = 0 V,
VIN = 1.65 V
Channel Resistance (Pins 1−8, 2−7)
Rch
Differential Mode Cut*Off Frequency
f3dB
Common Mode Stop Band Attenuation
In−system ESD Withstand Voltage
a) Contact discharge per IEC 61000−4−2
standard, Level 4 (External Pins − Pin1, Pin2)
b) Contact discharge per IEC 61000−4−2
standard, Level 1 (Internal Pins)
c) Contact discharge per IEC 61000−4−2
standard, Level 4 (External Pins − VBUS, VID)
Min
Typ
TA = 25°C, VIN = 5 V, GND = 0 V
0.1
0.8
Max
Unit
1.0
mA
1.5
V
1.3
pF
8.0
W
50 W source and load termination
2.0
GHz
Fatten
@ 800 MHz
30
dB
VESD
(Notes 1 and 2)
kV
±12
±2
±30
TLP Clamping Voltage − pin1, pin2
(See Figure 10)
VCL
Forward IPP = 8 A
Forward IPP = 12 A
Reverse IPP = −8 A
Reverse IPP = −12 A
13
16
−6
−8.5
V
V
V
V
TLP Clamping Voltage − VBUS
(See Figure 11)
VCL
Forward IPP = 8 A
Forward IPP = 12 A
Reverse IPP = −8 A
Reverse IPP = −12 A
23
25
−4
−5.4
V
V
V
V
Reverse Working Voltage (Pins 1,2,8,7 and 6)
Breakdown Voltage (Pins 1,2,8,7 and 6)
Reverse Working Voltage (VBUS)
Breakdown Voltage (VBUS)
VRWM
VBR
VRWM(2)
(Note 3)
IT = 1 mA; (Note 4)
5.5
(Note 3)
V
9.0
V
12
V
16.8
V
VBR(2)
IT = 1 mA; (Note 4)
Maximum Peak Pulse Current (VID to GND)
IPP
8x20 ms Waveform
12
A
Clamping Voltage (VID to GND)
VC
IPP = 5 A
10
V
5
A
Maximum Peak Pulse Current (VBUS to GND)
IPP(2)
8x20 ms Waveform
Clamping Voltage (VBUS to GND)
VC(2)
IPP = 5 A
Dynamic Resistance
Positive Transients
Negative Transients
RDYN
TA = 25C, IPP=1 A, tP= 8/20 ms,
Any I/O to GND
15
5.0
25
V
0.67
0.59
W
W
1. Standard IEC 61000−4−2 with CDischarge = 150 pF, RDischarge = 330, GND grounded.
2. These measurements performed with no external capacitor.
3. TVS devices are normally selected according to the working peak reverse voltage (VRWM), which should be equal or greater than the DC
or continuous peak operating voltage level.
4. VBR is measured at pulse test current IT.
http://onsemi.com
3
EMI2124
I/O 1
I/O 8
I/O 2
I/O 7
EMI2124
2
4
Network Analyzer
1
3
Normal (Differential) Mode
Figure 1. Normal (Differential) Mode Test
Configuration
I/O 1
I/O 8
I/O 2
I/O 7
Differential Signal Driver and
Transmission Line
EMI2124
Figure 2. Application Circuit
http://onsemi.com
4
Differential Signal Buffer and
Transmission Line
EMI2124
TYPICAL CHARACTERISTICS
Figure 3. Differential Mode Attenuation vs.
Frequency (Zdiff = 100 W)
Figure 4. Common Mode Attenuation vs.
Frequency (Zcomm = 50 W)
Figure 5. Differential Return Loss vs. Frequency
(Zdiff=100 W)
Figure 6. Differential Impedance vs. Frequency
(Zdiff=100 W)
Figure 7. EMI2124 Measured Eye Diagram @ 480 Mbps
http://onsemi.com
5
EMI2124
Transmission Line Pulse (TLP) Measurements
Transmission Line Pulse (TLP) provides current versus voltage (I-V) curves in which each data point is obtained from a
100 ns long rectangular pulse from a charged transmission line. A simplified schematic of a typical TLP system is shown in
Figure 8. TLP I-V curves of ESD protection devices accurately demonstrate the product’s ESD capability because the 10 s of
amps current levels and under 100 ns time scale match those of an ESD event. This is illustrated in Figure 9 where an 8 kV
IEC61000-4-2 current waveform is compared with TLP current pulses at 8 and 16 A. A TLP curve shows the voltage at which
the device turns on as well as how well the device clamps voltage over a range of current levels. Typical TLP I-V curves for
the EMI2124 are shown in Figure 10.
L
SW
50 W Coax
Cable
Attenuator
50 W Coax Cable
÷
IM
VM
10 MW
VC
DUT
Oscilloscope
Figure 8. Simplified Schematic of a Typical TLP System
Figure 9. Comparison Between 8 kV IEC61000−4−2 and 8 A and 16 A TLP Waveforms
http://onsemi.com
6
EMI2124
-14
12
-12
10
-10
) 8
(A
t
n
re
r 6
u
C
-8
Current (A)
Current (A)
14
-6
4
-4
2
-2
0
0
0
2
4
6
8
10
12
14
16
0
18
-2
-4
-6
Voltage (V)
Voltage (V)
Figure 10. Positive and Negative TLP Waveforms (Pin1, Pin2)
Figure 11. Positive and Negative TLP Waveforms (VBUS)
http://onsemi.com
7
-8
-10
EMI2124
ESD Voltage Clamping
For sensitive circuit elements it is important to limit the voltage that an IC will be exposed to during an ESD event to as low
a voltage as possible. The ESD clamping voltage is the voltage drop across the ESD protection diode during an ESD event per
the IEC61000−4−2 waveform. Since the IEC61000−4−2 was written as a pass/fail spec for larger systems such as cell phones
or laptop computers it is not clearly defined in the spec how to specify a clamping voltage at the device level. ON Semiconductor
has developed a way to examine the entire voltage waveform across the ESD protection diode over the time domain of an ESD
pulse in the form of an oscilloscope screenshot, which can be found on the datasheets for all ESD protection diodes. For more
information on how ON Semiconductor creates these screenshots and how to interpret them please refer to On Semiconductor
Application Notes AND8307/D and AND8308/D.
IEC61000−4−2 Waveform
IEC61000−4−2 Spec.
Ipeak
Level
Test
Voltage
(kV)
First Peak
Current
(A)
Current at
30 ns (A)
Current at
60 ns (A)
1
2
7.5
4
2
2
4
15
8
4
3
6
22.5
12
6
4
8
30
16
8
100%
90%
I @ 30 ns
I @ 60 ns
10%
tP = 0.7 ns to 1 ns
Oscilloscope
TVS
50 W
Cable
50 W
Figure 12. Diagram of ESD Test Setup
100
% OF PEAK PULSE CURRENT
ESD Gun
PEAK VALUE IRSM @ 8 ms
tr
90
PULSE WIDTH (tP) IS DEFINED
AS THAT POINT WHERE THE
PEAK CURRENT DECAY = 8 ms
80
70
60
HALF VALUE IRSM/2 @ 20 ms
50
40
30
tP
20
10
0
0
20
40
t, TIME (ms)
60
Figure 13. 8 x 20 ms Pulse Waveform
http://onsemi.com
8
80
EMI2124
Figure 14. ESD Clamping Voltage +8 kV per IEC6100−4−2 (external to internal pin)
Figure 15. ESD Clamping Voltage −8 kV per IEC6100−4−2 (external to internal pin)
http://onsemi.com
9
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
WDFN8, 2.2x2, 0.5P
CASE 511BN
ISSUE A
8
DATE 11 DEC 2012
1
SCALE 4:1
PIN ONE
REFERENCE
2X
L
A B
D
ÉÉÉ
ÉÉÉ
ÉÉÉ
L1
E
DETAIL A
OPTIONAL
CONSTRUCTIONS
0.10 C
0.10 C
2X
ÇÇ
ÇÇ
ÉÉ
EXPOSED Cu
TOP VIEW
A
DETAIL B
0.05 C
MOLD CMPD
ÉÉ
ÉÉ
ÇÇ
A1
DETAIL B
9X
0.05 C
OPTIONAL
CONSTRUCTIONS
A3
A1
SIDE VIEW
NOTE 4
SEATING
PLANE
C
b1
0.10 C A B
DETAIL C
D2
1
4X
2X
4
DIM
A
A1
A3
b
b1
D
D2
E
E2
e
L
L1
L2
L3
L
L3
DETAIL C
1
8
b
0.10 C A B
DETAIL A
e/2
NOTE 3
*This information is generic. Please refer
to device data sheet for actual part
marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
BOTTOM VIEW
RECOMMENDED
SOLDERING FOOTPRINT*
7X
0.54
0.30
XX MG
G
XX = Specific Device Code
M = Date Code
G
= Pb−Free Device
5
e
MILLIMETERS
MIN
MAX
0.70
0.80
0.00
0.05
0.20 REF
0.15
0.25
0.25
0.35
2.20 BSC
0.34
0.54
2.00 BSC
0.60
0.80
0.50 BSC
0.75
0.95
0.05
0.15
0.30
0.50
0.15
0.25
GENERIC
MARKING DIAGRAM*
L2
E2
A3
0.10 C A B
7X
0.05 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.25 mm FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
PACKAGE
OUTLINE
0.80
2.30
4X
4X
1.00
0.60
1
0.50
PITCH
0.40
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DOCUMENT NUMBER:
DESCRIPTION:
98AON52381E
WDFN8, 2.2X2.0, 0.5P
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative