Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FAN5353
3 MHz, 3 A Synchronous Buck Regulator
Features
Description
The FAN5353 is a step-down switching voltage regulator that
delivers an adjustable output from an input voltage supply of
2.7 V to 5.5 V. Using a proprietary architecture with
synchronous rectification, the FAN5353 is capable of
delivering 3 A at over 85% efficiency. The regulator operates
at a nominal fixed frequency of 3 MHz, which reduces the
value of the external components to 470 nH for the output
inductor and 10 µF for the output capacitor. Additional output
capacitance can be added without affecting stability if tighter
regulation during transients is required. The regulator
includes an open-drain power good (PGOOD) signal that
pulls low when the output is not in regulation.
3 MHz Fixed-Frequency Operation
Best-in-Class Load Transient
3 A Output Current Capability
2.7 V to 5.5 V Input Voltage Range
Adjustable Output Voltage: 0.8 V to 90% of VIN
Power Good Output
Internal Soft-Start
Input Under-Voltage Lockout (UVLO)
Thermal Shutdown and Overload Protection
12-Lead, 3 x 3.5 mm MLP
In shutdown mode, the supply current drops below 1 µA,
reducing power consumption.
FAN5353 is available in a 12-lead 3x3.5 mm MLP package.
Set-Top Box
R1
Hard Disk Drive
COUT
Communications Cards
FB
VOUT
PGND
DSP Power
PGND
L1
R2
SW
SW
AGND
1
12
2
11
3
4
P1
(GND)
10
9
5
8
6
7
PGOOD
EN
CVCC
VCC
PVIN
R3
Applications
PVIN
CIN1
CIN
Figure 1. Typical Application
Ordering Information
Part Number
Temp. Range
Package
Packing Method
FAN5353MPX
-40 to 85°C
MLP-12, 3 x 3.5 mm
Tape and Reel
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
December 2013
Component
Description
Vendor
Parameter
Typ.
Units
L
0.47
µH
L1
470 nH nominal
Vishay — IHLP1616ABER47M01
Coiltronics — SD12-R47-R
TDK — VLC5020T-R47N,
MURATA — LQH55PNR47NT0
DCR
20
mΩ
COUT
2 pieces
10 µF, 6.3 V, X5R, 0805
C
10.0
µF
CIN
10 µF, 6.3 V, X5R, 0805
GRM21BR60J106M (Murata)
C2012X5R0J106M (TDK)
CIN1
10 nF, 25 V, X7R, 0402
GRM155R71E103K (Murata)
C1005X7R1E103K (TDK)
C
10
nF
CVCC
4.7 µF, 6.3 V, X5R, 0603
GRM188R60J475K (Murata)
C1608X5R0J475K (TDK)
C
4.7
µF
Resistor: 1 Ω 0402
any
R
1
Ω
R3
(1)
Note:
1. R3 is optional and improves IC power supply noise rejection. See Layout recommendations for more information.
Pin Configuration
FB 1
12 NC
VOUT 2
PGND 3
PGND 4
11 PGOOD
P1
(GND)
10 EN
9 VCC
SW 5
8 PVIN
SW 6
7 PVIN
Figure 2. 12-Pin, 3 x 3.5 mm MLP (Top View)
Pin Definitions
Pin #
Name
Description
FB. Connect to resistor divider. The IC regulates this pin to 0.8 V.
1
FB
2
VOUT
VOUT. Sense pin for VOUT. Connect to COUT.
3, 4
PGND
Power Ground. Low-side MOSFET is referenced to this pin. CIN and COUT should be returned with a
minimal path to these pins.
5, 6
SW
Switching Node. Connect to inductor.
P1
GND
Ground. All signals are referenced to this pin.
7, 8
PVIN
Power Input Voltage. Connect to input power source. Connect to CIN with minimal path.
9
VCC
IC Bias Supply. Connect to input power source. Use a separate bypass capacitor CVCC from this pin
to the P1 GND terminal between pins 1 and 12.
10
EN
11
PGOOD
12
NC
Enable. The device is in shutdown mode when this pin is LOW. Do not leave this pin floating.
Power Good. This open-drain pin pulls LOW if the output falls out of regulation or is in soft-start.
This pin has no function and should be tied to GND.
Note:
2. P1 is the bottom heat-sink pad. Ground plane should flow through pins 3, 4, 12, and P1 and can be extended through pin
11 if PGOOD’s function is not required to improve IC cooling.
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
2
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Table 1. Recommended External Components for 3 A Maximum Load Current
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above
the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended
exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum
ratings are stress ratings only.
Symbol Parameter
VIN
Voltage on SW, PVIN, VCC Pins
Min.
Max.
IC Not Switching
-0.3
7.0
IC Switching
-0.3
6.5
Voltage on Other Pins
-0.3
VCC + 0.3
VINOV_SLEW Maximum Slew Rate of VIN Above 6.5 V when PWM is Switching
RPGOOD
Unit
V
(3)
15
Pull-Up Resistance from PGOOD to VCC
1
V
V/ms
kΩ
Human Body Model per JESD22-A114
2
Charged Device Model per JESD22-C101
2
ESD
Electrostatic Discharge
Protection Level
TJ
Junction Temperature
–40
+150
°C
TSTG
Storage Temperature
–65
+150
°C
+260
°C
TL
kV
Lead Soldering Temperature, 10 Seconds
Note:
3. Lesser of 7 V or VCC+0.3 V.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating
conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend
exceeding them or designing to Absolute Maximum Ratings.
Symbol
Parameter
Min.
Typ.
Max.
Unit
VCC, VIN
Supply Voltage Range
2.7
5.5
V
VOUT
Output Voltage Range
0.8
90% Duty Cycle
V
IOUT
Output Current
0
3
A
L
CIN
COUT
Inductor
0.47
µH
Input Capacitor
10
µF
Output Capacitor
20
µF
TA
Operating Ambient Temperature
-40
+85
°C
TJ
Operating Junction Temperature
-40
+125
°C
Thermal Properties
Symbol
θJA
Parameter
Junction-to-Ambient Thermal Resistance
Min.
(4)
Typ.
46
Max.
Unit
°C/W
Note:
4. Junction-to-ambient thermal resistance is a function of application and board layout. This data is measured with four-layer
1s2p boards in accordance to JESD51- JEDEC standard. Special attention must be paid not to exceed junction
temperature TJ(max) at a given ambient temperate TA.
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
3
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Absolute Maximum Ratings
Minimum and maximum values are at VIN = 2.7 V to 5.5 V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = 25°C, VIN =5 V.
Symbol Parameter
Conditions
Min.
Typ.
Max.
Unit
Power Supplies
IQ
Quiescent Current
ILOAD = 0, VOUT=1.2 V
14
I SD
Shutdown Supply Current
EN = GND
0.1
3.0
µA
2.83
2.95
V
2.30
2.40
V
VUVLO
Under-Voltage Lockout Threshold
VUVHYST
Under-Voltage Lockout Hysteresis
VIN Rising
VIN Falling
2.10
mA
530
mV
Logic Pins
VIH
HIGH-Level Input Voltage
VIL
LOW-Level Input Voltage
VLHYST
IIN
1.05
V
0.4
Logic Input Hysteresis Voltage
100
Input Bias Current
Input tied to GND or VIN
IOUTL
PGOOD Pull-Down Current
VPGOOD = 0.4 V
IOUTH
PGOOD HIGH Leakage Current
VPGOOD = VIN
V
mV
1.00
µA
1
mA
0.01
1.00
µA
0.792
0.800
0.808
V
0.788
0.800
0.812
V
+1.6
%
0.01
VOUT Regulation
TA = 25°C
VREF
Output Reference DC Accuracy
Measured at FB Pin
VREG
VOUT DC Accuracy
At VOUT pin W.R.T. Calculated
Value, ILOAD = 500 mA
∆VOUT
∆ILOAD
Load Regulation
IOUT(DC) = 0 to 3 A
–0.03
%/A
∆VOUT
∆VIN
Line Regulation
2.7 V ≤ VIN ≤ 5.5 V,
IOUT(DC) = 1.5 A
0.01
%/V
Transient Response
ILOAD step 0.1 A to 1.5 A,
tr = tf = 100 ns, VOUT=1.2 V
±20
mV
60
mΩ
1.6%
Power Switch and Protection
RDS(ON)P
P-channel MOSFET On Resistance
RDS(ON)N
N-channel MOSFET On Resistance
ILIMPK
P-MOS Peak Current Limit
TLIMIT
Thermal Shutdown
THYST
Thermal Shutdown Hysteresis
VSDWN
Input OVP Shutdown
mΩ
40
3.75
4.55
5.50
A
150
°C
20
°C
6.2
V
5.50
5.85
V
2.7
3.0
3.3
MHz
RLOAD > 5 Ω, to VOUT = 1.2 V
210
250
µs
RLOAD > 5 Ω, to VOUT = 1.8 V
340
420
µs
Rising Threshold
Falling Threshold
Frequency Control
fSW
Oscillator Frequency
Soft-Start
tSS
VSLEW
Regulator Enable to Regulated VOUT
Soft-Start VOUT Slew Rate
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
10
V/ms
www.fairchildsemi.com
4
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Electrical Characteristics
Unless otherwise specified, VIN = 5 V, VOUT = 1.2 V, circuit of Figure 1, and components per Table 1.
100%
90%
90%
80%
80%
70%
70%
Efficiency
100%
Efficiency
60%
50%
VIN = 3.3V
40%
60%
50%
40%
VIN = 5V
30%
VIN = 3.3V
30%
20%
20%
10%
10%
0%
0%
1
10
100
1000
1
10000
10
100%
100%
90%
90%
80%
80%
70%
70%
60%
VIN = 3.3V
40%
VIN = 5V
1000
10000
Figure 4. Efficiency vs. ILOAD at VOUT = 1.8 V
Efficiency
Efficiency
Figure 3. Efficiency vs. ILOAD at VOUT = 1.2 V
50%
100
I LOAD Output Current (mA)
I LOAD Output Current (mA)
60%
VIN = 4.2V
50%
VIN = 5V
40%
30%
30%
20%
20%
10%
10%
0%
0%
1
10
100
1000
10000
1
10
I LOAD Output Current (mA)
1000
10000
Figure 6. Efficiency vs. ILOAD at VOUT = 3.3 V
1
16
0.9
15
Quiescent Current (mA)
0.8
0.7
0.6
0.5
100
I LOAD Output Current (mA)
Figure 5. Efficiency vs. ILOAD at VOUT = 2.5 V
Supply Current (µA)
VIN = 5V
85°C
0.4
25°C
0.3
-40°C
0.2
14
13
12
85°C
11
25°C
–40°C
10
9
0.1
8
0
2.7
3.2
3.7
4.2
4.7
2.7
5.2
3.7
4.2
4.7
5.2
VIN Input Voltage (V)
Input Voltage(V)
Figure 7. Shutdown Supply Current vs. VIN, EN to 0 V
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
3.2
Figure 8. Quiescent Current vs. VIN, No Load
www.fairchildsemi.com
5
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Typical Characteristics
Unless otherwise specified, VIN = 5 V, VOUT = 1.2 V, circuit of Figure 1, and components per Table 1.
VOUT
VOUT
IL
IL
Iload
I load
Figure 10. Load Transient Response: 500 mA to 3 A to
500 mA, tr=tf=100 ns, Horizontal Scale = 5 µs/div.
Figure 9. Load Transient Response: 100 mA to 1.5 A to
100 mA, tr=tf=100 ns, Horizontal Scale = 5 µs/div.
20
3.5
18
5VIN,1.2VOUT
3.0
3.3VIN,1.2VOUT
14
Switching Frequency (Mhz)
VOUT ripple (mV AC pp)
16
5VIN, 3.3VOUT
12
10
8
6
4
2.5
2.0
1.5
VIN = 4.1V
VIN = 4.0V
1.0
VIN = 3.9V
VIN = 3.8V
0.5
2
-
0
0.1
1
10
100
1000
0
10000
Load Current (mA)
0.5
1
1.5
2
2.5
3
Load Current (A)
Figure 11. Output Voltage Ripple vs. Load Current
Figure 12. Effect of tOFF Minimum on Reducing the
Switching Frequency at Large Duty Cycles, VOUT = 3.3 V
PSRR
Attenuation (dB)
90
80
70
V IN
60
50
1.2VOUT,1.5A load
40
VOUT
1.2VOUT, 3A load
30
3.3VOUT,1.5A load
20
0.01
0.1
1
10
100
Frequency (KHz)
Figure 13. Power Supply Rejection Ratio
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
Figure 14. Line Transient Response with 1 A load,
10 µs/div.
www.fairchildsemi.com
6
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Typical Characteristics
Unless otherwise specified, VIN = 5 V, VOUT = 1.2 V, circuit of Figure 1, and components per Table 1.
VEN
VIN=VEN
VOUT
VOUT
VPG
VPG
Isupply
Isupply
Figure 16. Soft-Start: EN Pin Tied to VCC,
ILOAD = 0, Horizontal Scale = 1 ms/div.
Figure 15. Soft-Start: EN Voltage Raised After VIN =5.0 V,
ILOAD = 0, Horizontal Scale = 100 µs/div.
VEN
VIN=VEN
VOUT
VOUT
VPG
VPG
Isupply
Isupply
Figure 17. Soft-Start: EN Pin Raised after VIN = 5.0 V,
RLOAD = 400 mΩ. COUT = 100 µF, Horizontal Scale =
100µs/div.
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
Figure 18. Soft-Start: EN Pin Tied to VCC, RLOAD =
400 mΩ, COUT = 100 µF, Horizontal Scale = 1 ms/div.
www.fairchildsemi.com
7
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Typical Characteristics
Unless otherwise specified, VIN = 5 V, VOUT = 1.2 V, circuit of Figure 1, and components per Table 1.
VOUT
VOUT
IL
IL
VPG
VPG
Figure 19. VOUT to GND Short Circuit, 200 µs/div.
Figure 20. VOUT to GND Short Circuit, 5 µs/div.
VEN
VOUT
VOUT
IL
IL
VPG
VPG
Figure 22. Progressive Overload, 200 µs/div.
Figure 21. Over-Current at Startup: RLOAD = 200 mΩ.,
50 µs/div.
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
8
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Typical Characteristics
The FAN5353 is a step-down switching voltage regulator
that delivers an adjustable output from an input voltage
supply of 2.7 V to 5.5 V. Using a proprietary architecture with
synchronous rectification, the FAN5353 is capable of
delivering 3 A at over 80% efficiency. The regulator operates
at a nominal frequency of 3 MHz at full load, which reduces
the value of the external components to 470 nH for the
output inductor and 20 µF for the output capacitor.
PGOOD Pin
1.
The IC has operated in cycle-by-cycle current limit for
eight or more consecutive PWM cycles.
Control Scheme
2.
The circuit is disabled; either after a fault occurs, or
when EN is LOW.
3.
The IC is performing a soft-start.
The PGOOD pin is an open drain output that indicates the IC
is in regulation when its state is open. PGOOD requires an
external pull-up resistor. PGOOD pulls LOW under the
following conditions:
The FAN5353 uses a proprietary non-linear, fixed-frequency
PWM modulator to deliver a fast load transient response,
while maintaining a constant switching frequency over a wide
range of operating conditions. The regulator performance is
independent of the output capacitor ESR, allowing for the use
of ceramic output capacitors. Although this type of operation
normally results in a switching frequency that varies with input
voltage and load current, an internal frequency loop holds the
switching frequency constant over a large range of input
voltages and load currents.
Under-Voltage Lockout
When EN is HIGH, the under-voltage lockout keeps the part
from operating until the input supply voltage rises high
enough to properly operate. This ensures no misbehavior of
the regulator during startup or shutdown.
Input Over-Voltage Protection (OVP)
When VIN exceeds VSDWN (about 6.2 V) the IC stops switching,
to protect the circuitry from internal spikes above 6.5 V. An
internal 40 µs filter prevents the circuit from shutting down due
to noise spikes. For the circuit to fully protect the internal
circuitry, the VIN slew rate above 6.2 V must be limited to no
more than 15 V/ms when the IC is switching.
Setting the Output Voltage
The output voltage is set by the R1, R2, and VREF (0.8 V):
R1 VOUT − VREF
=
R2
VREF
(1)
R1 must be set at or below 100 kΩ. Therefore:
R2 =
The IC protects itself if VIN overshoots to 7 V during initial
power-up as long as the VIN transition from 0 to 7 V occurs in
less than 10 µs (10% to 90%).
R1 • 0.8
(VOUT − 0.8)
(2)
Current Limiting
For example, for VOUT = 1.2 V, R1 = 100 kΩ, R2 = 200 kΩ.
A heavy load or short circuit on the output causes the current
in the inductor to increase until a maximum current threshold
is reached in the high-side switch. Upon reaching this point,
the high-side switch turns off, preventing high currents from
causing damage. 16 consecutive PWM cycles in current limit
cause the regulator to shut down and stay off for about
1200µs before attempting a restart.
Enable and Soft Start
When the EN pin is LOW, the IC is shut down, all internal
circuits are off, and the part draws very little current. Raising
EN above its threshold voltage activates the part and starts
the soft-start cycle. During soft-start, the modulator’s internal
reference is ramped slowly to minimize any large surge
currents on the input and prevents any overshoot of the
output voltage.
In the event of a short circuit, the soft-start circuit attempts to
restart and produces an over-current fault after about 50 µs,
which results in a duty cycle of less than 10%, providing
current into a short circuit.
If large values of output capacitance are used, the regulator
may fail to start. If VOUT fails to achieve regulation within
320 µs from the beginning of soft-start, the regulator shuts
down and waits 1200 µs before attempting a restart. If the
regulator is at its current limit for more than about 60 µs, the
regulator shuts down before restarting 1200 µs later. This
limits the COUT capacitance when a heavy load is applied
during the startup. For a typical FAN5353 starting with a
resistive load:
Thermal Shutdown
When the die temperature increases, due to a high load
condition and/or a high ambient temperature, the output
switching is disabled until the temperature on the die has
fallen sufficiently. The junction temperature at which the
thermal shutdown activates is nominally 150°C with a
20°C hysteresis.
COUTMAX ( µF) ≈ 400 − 100 ∗ ILOAD ( A )
where ILOAD =
VOUT
RLOAD
(3)
Synchronous rectification is inhibited during soft-start,
allowing the IC to start into a pre-charged load.
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
9
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Operation Description
shows the effects of inductance higher or lower than the
recommended 470 nH on regulator performance.
tON(MIN) and tOFF(MIN) are both 45 ns. This imposes constraints
on the maximum VOUT that the FAN5353 can provide,
VIN
while still maintaining a fixed switching frequency in PWM
mode. While regulation is unaffected, the switching
frequency drops when the regulator cannot provide sufficient
duty cycle at 3 MHz to maintain regulation.
Table 2. Effects of Increasing the Inductor
Value (from 470nH recommended value) on
Regulator Performance
IMAX(LOAD)
(4)
Decrease
Degraded
Inductor Current Rating
The FAN5353’s current limit circuit can allow a peak current
of 5.5 A to flow through L1 under worst-case conditions. If it
is possible for the load to draw that much continuous current,
the inductor should be capable of sustaining that current or
failing in a safe manner.
where:
VOUT + IOUT • R OFF
t SW (MAX ) = 45ns • 1 +
V
IN − IOUT • R ON − VOUT
Transient
Response
Increase
The calculation for switching frequency is given as:
1
1
fSW = min
,
t SW (MAX ) 333.3ns
∆VOUT (EQ. 8)
R OFF = RDSON _ N + DCRL
R ON = RDSON _ P + DCRL
For space-constrained applications, a lower current rating for
L1 can be used. The FAN5353 may still protect these
inductors in the event of a short circuit, but may not be able
to protect the inductor from failure if the load is able to draw
higher currents than the DC rating of the inductor.
Applications Information
Output Capacitor
Selecting the Inductor
Table 1 suggests 0805 capacitors, but 0603 capacitors may
be used if space is at a premium. Due to voltage effects, the
0603 capacitors have a lower in-circuit capacitance than the
0805 package, which can degrade transient response and
output ripple.
The output inductor must meet both the required inductance
and the energy handling capability of the application. The
inductor value affects the average current limit, the output
voltage ripple, and the efficiency.
Increasing COUT has no effect on loop stability and can
therefore be increased to reduce output voltage ripple or to
improve transient response. Output voltage ripple, ∆VOUT, is:
The ripple current (∆I) of the regulator is:
∆I ≈
VOUT VIN − VOUT
•
VIN
L • fSW
(5)
1
∆VOUT = ∆I •
+ ESR
8 • C OUT • fSW
The maximum average load current, IMAX(LOAD) is related to
the peak current limit, ILIM(PK)by the ripple current as:
IMAX(LOAD ) = ILIM(PK ) −
∆I
2
where COUT is the effective output capacitance. The
capacitance of COUT decreases at higher output voltages,
which results in higher ∆VOUT .
(6)
If COUT is greater than 100 µF, the regulator may fail to start
under load.
The FAN5353 is optimized for operation with L=470 nH, but
is stable with inductances up to 1.2 µH (nominal). The
inductor should be rated to maintain at least 80% of its value
at ILIM(PK). Failure to do so lowers the amount of DC current
the IC can deliver.
If an inductor value greater than 1.0 µH is used, at least
30 µF of COUT should be used to ensure stability.
ESL Effects
Efficiency is affected by the inductor DCR and inductance
value. Decreasing the inductor value for a given physical
size typically decreases the DCR; but since ∆I increases, the
RMS current increases, as do core and skin effect losses.
IRMS =
IOUT(DC) 2 +
∆I2
12
The ESL (Equivalent Series Inductance) of the output
capacitor network should be kept low to minimize the square
wave component of output ripple that results from the
division ratio COUT’s ESL and the output inductor (LOUT). The
square wave component due to ESL can be estimated as:
(7)
∆VOUT(SQ ) ≈ VIN •
The increased RMS current produces higher losses through
the RDS(ON) of the IC MOSFETs as well as the inductor ESR.
ESL COUT
L1
(9)
A good practice to minimize this ripple is to use multiple
output capacitors to achieve the desired COUT value. For
example, to obtain COUT = 20 µF, a single 22 µF 0805 would
produce twice the square wave ripple of 2 x 10 µF 0805.
Increasing the inductor value produces lower RMS currents,
but degrades transient response. For a given physical
inductor size, increased inductance usually results in an
inductor with lower saturation current.
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
(8)
www.fairchildsemi.com
10
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Minimum Off-Time Effect on Switching
Frequency
VCC and VIN should be connected together by a thin trace
some distance from the IC, or through a resistor (shown as
R3 below), to isolate the switching spikes on PVIN from the
IC bias supply on VCC. If PCB area is at a premium, the
connection between PVIN and VCC can be made on another
PCB layer through vias. The via impedance provides some
filtering for the high-frequency spikes generated on PVIN.
Input Capacitor
PGND and AGND connect through the thermal pad of the
IC. Extending the PGND and AGND planes improves IC
cooling. The IC analog ground (AGND) is bonded to P1
between pins 1 and 12. Large AC ground currents should
return to pins 3 and 4 (PGND) either through the copper
under P1 between pins 6 and 7 or through a direct trace
from pins 3 and 4 (as shown for COUT1-COUT3).
The 10µF ceramic input capacitor should be placed as close
as possible between the VIN pin and PGND to minimize the
parasitic inductance. If a long wire is used to bring power to
the IC, additional “bulk” capacitance (electrolytic or tantalum)
should be placed between CIN and the power source lead to
reduce under-damped ringing that can occur between the
inductance of the power source leads and CIN.
EN and PGOOD connect through vias to the system control
logic.
The effective CIN capacitance value decreases as VIN
increases due to DC bias effects. This has no significant
impact on regulator performance.
CIN1 is an optional device used to provide a lower
impedance path for high-frequency switching edges/spikes,
which helps to reduce SW node and VIN ringing. CIN should
be placed as close as possible between PGND and VIN, as
shown below.
Layout Recommendations
The layout recommendations below highlight various topcopper planes by using different colors. It includes COUT3
to demonstrate how to add COUT capacitance to reduce
ripple and transient excursions. The inductor in this
example is the TDK VLC5020T-R47N.
PGND connection back to inner planes should be
accomplished as series of vias distributed among the COUT
return track and CIN return plane between pins 6 and 7.
AGND
0402
VOUT
10µF
0805
COUT1
10µF
0805
2
PGND
3
FAN5353
10
P1
(GND)
9 VCC
5
8
6
7
SW
0.47µH
5 x 5 mm
CIN1
CVCC
11
0402
4
L1
12
1
0603
10µF
0805
COUT2
0402
COUT3
R3
VIN
10µF
0805
0402
CIN
PGND
Figure 23. 3 A Layout Recommendation
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
11
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
To minimize ESL, try to use capacitors with the lowest ratio
of length to width. 0805s have lower ESL than 1206s. If low
output ripple is a chief concern, some vendors produce 0508
or 0612 capacitors with ultra-low ESL. Placing additional
small value capacitors near the load also reduces the highfrequency ripple components.
2X
0.10 A
A
3.50
2.60
B
0.85
2.65
PIN#1 IDENT
3.00
2.84
0.10 B
TOP VIEW
2X
1.85
1.05
0.85
0.8 MAX
0.10 C
(0.2)
LAND PATTERN RECOMMENDATION
0.08 C
SIDE VIEW
0.05
0.00
C
2.60+/-0.05
SEATING PLANE
(0.38)
PIN#1 IDENT
6
1
1.60+/-0.05
0.25+/-0.05
0.45+/-0.05
(12X)
12
7
0.25+/-0.05 (12X)
0.50
BOTTOM VIEW
0.10
0.05
NOTES:
A. CONFORMS TO JEDEC MO-229
VARIATION WFED-2.
B. DIMENSIONS ARE IN MILLIMETERS
C. DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994
D. LANDPATTERN RECOMMENDATION IS
BASED ON IPC 7351 DESIGN GUIDELINES
E. LANDPATTERN EXTENSION TO INCLUDE
CENTER PAD TABS IS OPTIONAL
F. FILENAME AND REV: MKT-MLP12DREV1
C A B
C
Figure 24. 12-Lead, 3x3.5 mm Molded Leadless Package (MLP)
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without
notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most
recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty
therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/dwg/ML/MLP12D.pdf.
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
12
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
Physical Dimensions
FAN5353 — 3 MHz, 3 A Synchronous Buck Regulator
© 2009 Fairchild Semiconductor Corporation
FAN5353 • Rev. 1.0.3
www.fairchildsemi.com
13
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com
工商网监
湘ICP备2023018690号
