Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FAN7711
Ballast Control Integrated Circuit
Features
Description
Floating Channel for Bootstrap Operation to +600V
The FAN7711, developed with Fairchild’s unique highvoltage process, is a ballast control integrated circuit (IC)
for a fluorescent lamp. FAN7711 incorporates a preheating
/ ignition function, controlled by an user-selected external
capacitor, to increase lamp life. The FAN7711 detects
switch operation from after ignition mode through an
internal active Zero-Voltage Switching (ZVS) control
circuit. This control scheme enables the FAN7711 to
detect an open-lamp condition, without the expense of
external circuitry, and prevents stress on MOSFETs. The
high-side driver built into the FAN7711 has a commonmode noise cancellation circuit that provides robust
operation against high-dv/dt noise intrusion.
Low Start-up and Operating Current: 120μA, 3.2mA
Under-Voltage Lockout with 1.8V of Hysteresis
Adjustable Run Frequency and Preheat Time
Internal Active ZVS Control
Internal Protection Function (Latch Mode)
Internal Clamping Zener Diode
High Accuracy Oscillator
Soft-Start Functionality
Applications
8-DIP
8-SOP
Electronic Ballast
Ordering Information
Part Number
Package
FAN7711N
8-DIP
FAN7711M
Pb-Free
Operating Temperature Range
Packing Method
Yes
-25°C ~ 125°C
Tube
Tube
8-SOP
FAN7711MX
Tape & Reel
Typical Application
D5
R3
D6
R1
U1
D1
VDD
D2
Main
Supply
RT
C1
CPH
D3
D4
GND
C2
R2
C3
1
8
2
7
FAN7711
3
6
4
5
VB
HO
R4
Q1
VS
LO
C4
D7
C5
L1
C6
R5
Q2
Lamp
C7
FAN7711 Rev. 1.00
Figure 1. Typical Application Circuit for Compact Fluorescent Lamp
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
FAN7711 — Ballast Control Integrated Circuit
May 2007
V DD
1
HIGH-SIDE DRIVER
VB
10V
REG
VDD sense
Reference
IPH
4V
RT 2
PRE-HEAT
Control
BGR UVLO
IPH*
IRT
CPH
CPH
0A
BIAS
TSD
3V 5V
R
Q
S
Q
SDL
SYSHALT
DEAD-TIME Control
Yes
2μA
VB
Q
R
Q
7
HO
6
VS
5
LO
SET
RESET
LOW-SIDE GATE DRIVER
VDDH/V DD
LSH
VDDH/V DD
LSH
OSCILLATOR
No
S
SDH
UVLO
IPH*
CPHIgnition freq.-> Normal running freq.
4 × 10 9
RT
(EQ 3)
Even in the active ZVS mode, shown as (D) in Figure 19,
the oscillation frequency is not changed. The dead-time
is varied according to the resonant tank characteristic.
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
(EQ 2)
where VCPH is the voltage of CPH capacitor.
.
VDD
(EQ 1)
fPRE = 1.6 × fOSC
www.fairchildsemi.com
8
FAN7711 Ballast Control Integrated Circuit
Typical Application Information
(C) Active ZVS mode
40dB
CPH voltage varies by
active ZVS control
circuit
8
(B) Ignition Mode
7
6
DTMAX
RL=100k
RL=10k
Preheating
frequency
3 2 1
Dead Time[μs]
(B)
0dB
(C)
RL=1k
(A) Preheating Mode
4
3
DTMIN
20dB
5
2
0
(D) Shutdown
mode
1
0
time
Oscillation
Frequency
(A)
Preheating Frequency:fPRE
Preheating
Mode
Ignition
Mode
Running frequency
RL=500
t0
Running Frequency:
fOSC
Running
Mode
t1 t2 t3
time
FAN7711 Rev. 1.00
FAN7711 Rev. 1.00
(D) Dead-time control mode
at fixed frequency
Figure 20. Operation Modes
Figure 19. LCC Transfer Function in Terms of
Lamp Impedance
3.1 Preheating Mode (t0~t1)
When VDD exceeds VDDTH(ST+), the FAN7711 starts
operation. At this time, an internal current source (IPH)
charges CPH. CPH voltage increases from 0V to 3V in
preheating mode. Accordingly, the oscillation frequency
follows the Equation 4. In this mode, the lamp is not
ignited, but warmed up for easy ignition. The preheating
time depends on the size of CPH:
3. Operation Modes
FAN7711 has four operation modes: (A) preheating
mode, (B) ignition mode, (C) active ZVS mode, and (D)
shutdown mode, depicted in Figure 20. The modes are
automatically selected by the voltage of CPH capacitor,
shown in Figure 20. In modes (A) and (B), the CPH acts
as a timer to determine the preheating and ignition times.
After the preheating and ignition modes, the role of the
CPH is changed to stabilize the active ZVS control
circuit. In this mode, the dead time of the inverter is
selected by the voltage of CPH. Only when FAN7711 is
in active ZVS mode is it possible to shut off the whole
system using CPH pin. Pulling the CPH pin below 2V in
active ZVS mode, causes the FAN7711 to enter
shutdown mode. In shutdown mode, all active operation
is stopped, except UVLO and some bias circuitry. The
shutdown mode is triggered by the external CPH control
or the active ZVS circuit. The active ZVS circuit
automatically detects lamp removal (open-lamp
condition) and decreases CPH voltage below 2V to
protect the inverter switches from damage.
fpreheat =
3 × CPH
IPH
[Sec.]
(EQ 4)
According to preheating process, the voltage across the
lamp to ignite is reduced and the lifetime of the lamp is
increased. In this mode, the dead time is fixed at its
maximum value.
3.2 Ignition Mode (t1~t2)
When the CPH voltage exceeds 3V, the internal current
source to charge CPH is increased about six times larger
than IPH, noted as IIG, causing rapid increase in CPH
voltage. The internal oscillator decreases the oscillation
frequency from fPRE to fOSC as CPH voltage increases.
As depicted in Figure 20, lowering the frequency
increases the voltage across the lamp. Finally, the lamp
ignites. Ignition mode is defined when CPH voltage lies
between 3V and 5V. Once CPH voltage reaches 5V, the
FAN7711 does not return to ignition mode, even if the
CPH voltage is in that range, until the FAN7711 restarts
from below VDDTH(ST-). Since the ignition mode
continues when CPH is from 3V to 5V, the ignition time is
given by:
t ignition =
2 × CPH
IIG
[Sec.]
(EQ 5)
In this mode, dead time varies according to the CPH
voltage.
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
9
FAN7711 Ballast Control Integrated Circuit
CPH voltage [V]
If the voltage of capacitor CPH is decreased below
~2.6V by an external application circuit or internal
protection circuit, the IC enters shutdown mode. Once
the IC enters shutdown mode, this status continues until
an internal latch is reset by decreasing VDD below
VDDTH(ST-). Figure 22 shows an example of external
shutdown control circuit.
When CPH voltage exceeds 5V, the operating frequency
is fixed to fOSC by RT. However, active ZVS operation is
not activated until CPH reaches ~6V. The FAN7711
prepares for active ZVS operation from the instant CPH
exceeds 5V during t2 to t3. When CPH becomes higher
than ~6V at t3, the active ZVS operation is activated. To
determine the switching condition, FAN7711 detects the
transition time of the output (VS pin) of the inverter by
using VB pin. From the output-transition information,
FAN7711 controls the dead time to meet the ZVS
condition. If ZVS is satisfied, the FAN7711 slightly
increases the CPH voltage to reduce the dead time and
to find optimal dead time, which increases the efficiency
and decreases the thermal dissipation and EMI of the
inverter switches. If ZVS fails, the FAN7711 decreases
CPH voltage to increase the dead time. CPH voltage is
adjusted to meet optimal ZVS operation. During the
active ZVS mode, the amount of the charging/
discharging current is the same as IPH. Figure 21 depicts
normal operation waveforms.
3
Shutdown
Figure 22. External Shutdown Circuit
The amount of the CPH charging current is the same as
IPH, making it possible to shut off the IC using small
signal transistor. FAN7711 provides active ZVS
operation by controlling the dead time according to the
voltage of CPH. If ZVS fails, even at the maximum dead
time, FAN7711 stops driving the inverter.
The FAN7711 thermal shutdown circuit senses the
junction temperature of the IC. If the temperature
exceeds ~160°C, the thermal shutdown circuit stops
operation of the FAN7711.
time
Dead time settling
3V
2V
Ignition
Lamp
Voltage
Running mode
Active ZVS mode
The current usages of shutdown mode and undervoltage lockout status are different. In shutdown mode,
some circuit blocks, such as bias circuits, are kept alive.
Therefore, the current consumption is slightly higher
than during under-voltage lockout.
time
0V
time
OUT
Preheating period
(Filament warm-up)
4. Automatic Open-Lamp Detection
0V
FAN7711 can automatically detect the open-lamp
condition. When the lamp is opened, the resonant tank
fails to make a closed-loop to the ground, as shown in
Figure 23. The supplied current from the VS pin is used
to charge and discharge the charge pump capacitor, CP.
Since the open-lamp condition means resonant tank
absence, it is impossible to meet ZVS condition. In this
condition, the power dissipation of the FAN7711, due to
capacitive load drive, is estimated as:
time
Zoom-in
t=1/fOSC
t=1/fOSC
GND
FAN7711 Rev. 1.00
VDD
Active ZVS activated
CPH
FAN7711
4
VDDTH(ST+)
VDDTH(ST-)
CPH
6V
5V
Q1
CPH
t=1/fOSC
Perfect ZVS
t=1/fOSC
Dead time
FAN7711 Rev. 1.00
Figure 21. Typical Transient Waveform from
Preheating to Active ZVS Mode
PDissipation =
1
× CP × VDC 2 × f
2
[W ]
(EQ 6)
where f is driving frequency and VDC is DC-link voltage.
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
10
FAN7711 Ballast Control Integrated Circuit
3.4 Shutdown Mode
3.3 Running and Active Zero-Voltage Switching
(AZVS) Modes (t2~)
VDC
When VDD is lower than VDDTH(ST+), it consumes very
little current, IST, making it possible to supply current to
the VDD pin using a resistor with high resistance (Rstart in
Figure 25). Once UVLO is released, the current
consumption is increased and whole circuits are
operated, which requires additional power supply for
stable operation. The supply must deliver at least several
mA. A charge pump circuit is a cost-effective method to
create an additional power supply and allows CP to be
used to reduce the EMI.
FAN7711
VDD
CVDD
RT
VB
Oscillator
High-side
driver
CB
HO
LCC resonant tank
RT
CPH
Dead-time
controller
CPH
GND
Low-side
driver
L
VS
RL
CP
LO
CCP
Dp1
FAN7711 Rev. 1.00
Filament Open
CS
equivalent lamp impedance
Dp2
Charge Pump
Figure 23. Current Flow When the Lamp is Open
VDC
DB
Rstart
+
Ccp
Dp1
equivalent lamp impedance
Dp2
Charge Pump
Figure 25. Local Power Supply for VDD Using a
Charge Pump Circuit
As presented in Figure 25, when VS is high, the inductor
current and CCP create an output transition with the
slope of dv/dt. The rising edge of VS charges CCP. At that
time, the current that flows through CCP is:
I ≅ CCP ×
dv
dt
(EQ 7)
This current flows along the path (1). It charges CVDD,
which is a bypass capacitor to reduce the noise on the
supply rail. If CVDD is charged over the threshold voltage
of the internal shunt regulator, the shunt regulator is
turned on and regulates VDD with the trigger voltage.
Automatic
Shutdown
When VS is changing from high to low state, CCP is
discharged through Dp2, shown as path (2) in Figure 26.
These charging/discharging operations are continued
until FAN7711 is halted by shutdown operation. The
charging current, I, must be large enough to supply the
operating current of FAN7711.
time
Active ZVS mode
time
The supply for the high-side gate driver is provided by
the boot-strap technique, as illustrated in Figure 26.
When the low-side MOSFET connected between VS and
GND pins is turned on, the charging current for VB flows
through DB. Every low VS gives the chance to charge the
CB. Therefore CB voltage builds up only when FAN7711
operates normally.
Shutdown
Ignition period mode
FAN7711 Rev. 1.00
Figure 24. CPH Voltage Variation in Open-Lamp
Condition
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
CP
LO
FAN7711 Rev. 1.00
Running mode
Preheating period
(Filament warm-up)
dv/dt
(2) LCC resonant tank
L CS Filament Open
VS
(1)
time
0V
CB
RL
3V
2V
OUT
Shunt
regulator
GND
Shutdown
Release Restart
Active ZVS activated
VB
HO
CPH
VDDTH(ST+)
VDDTH(ST-)
CPH
6V
5V
RT
CVDD
Figure 24 illustrates the waveforms during the openlamp condition. In this condition, the charging and
discharging current of CP is directly determined by
FAN7711 and considered hard-switching condition. The
FAN7711 tries to meet ZVS condition by decreasing
CPH voltage to increase dead time. If ZVS fails and CPH
goes below 2V, even though the dead time reaches its
maximum value, FAN7711 shuts off the IC to protect
against damage. To restart FAN7711, VDD must be
below VDDTH(ST-) to reset an internal latch circuit, which
remembers the status of the IC.
VDD
FAN7711
VDD
Assuming that CP, VDC, and f are 1nF, 311V, and 50kHz,
respectively; the power dissipation reaches about 2.4W
and the temperature of FAN7711 is increased rapidly. If
no protection is provided, the IC can be damaged by the
thermal attack. Note that hard-switching condition during
the capacitive-load drive causes lots of EMI.
www.fairchildsemi.com
11
FAN7711 Ballast Control Integrated Circuit
5. Power Supply
DB
FAN7711 Ballast Control Integrated Circuit
When VS goes high, the diode DB is reverse-biased and
CB supplies the current to the high-side driver. At this
time, since CB discharges, VB-VS voltage decreases. If
VB-VS goes below VHSTH(ST-), the high-side driver
cannot operate due to the high-side UVLO protection
circuit. CB must be chosen to be large enough not to fall
into UVLO range due to the discharge during a half of
the oscillation period, especially when the high-side
MOSFET is turned on.
DB Bootstrap circuit
VDC
Rstart
VDD
+
CVDD
FAN7711
RT
CPH
VB
CB
HO
Shunt
regulator
Charging path
VS
LCC resonant tank
L CS Filament Open
RL
GND
CCP
Dp1
FAN7711 Rev. 1.00
CP
LO
equivalent lamp impedance
Dp2
Charge Pump
Figure 26. Implementation of Floating Power Supply
Using the Bootstrap Method
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
12
1. Start-up Circuit
If Rstart meets Equation 14, restart operation is possible.
However, it is not recommended to choose Rstart at that
range because VDD rising time could be long and it
increases the lamp's turn-on delay time, as depicted in
Figure 27.
The start-up current (IST) is supplied to the IC through
the start-up resistor, Rstart. Once operation starts, the
power is supplied by the charge pump circuit. To reduce
the power dissipation in Rstart, select Rstart as high as
possible, considering the current requirements at startup. For 220VAC power, the rectified voltage by the fullwave rectifier makes DC voltage, as shown in Equation
8. The voltage contains lots of AC component due to
poor regulation characteristic of the simple full-wave
rectifier:
VDC = 2 × 220[V ] ≅ 311[V ]
VDD
VCL
VDDTH(ST+)
VDDTH(ST-)
tstart
(EQ 8)
Considering the selected parameters, Rstart must satisfy
the following equation:
VDC − VDDTH (ST + )
R start
> IST
0
Figure 27. VDD Build-up
(EQ 9)
Figure 28 shows the equivalent circuit for estimating
tstart. From the circuit analysis, VDD variation versus time
is given by:
From Equation 9, Rstart is selected as:
VDC − VDDTH (ST + )
IST
> R start
(
(EQ 10)
VDD (t ) = (VDC − Rstart ⋅ IST ) 1 − e −t /(Rstart ⋅CVDD )
Note that if choosing the maximum Rstart, it takes long
time for VDD to reach VDDTH(st+). Considering VDD rising
time, Rstart must be selected as shown in Figure 30.
− VCL )
R start
2
<
1
[W ]
4
tstart = −Rstart ⋅ CVDD ⋅ ln
tstart ≈
Rstart ⋅ CVDD ⋅ VDDTH (ST + )
VDC − Rstart ⋅ IST − VDDTH (ST + )
(EQ 17)
IST
VDD
RT
(1) For safe start-up without restart in shutdown mode:
2
(EQ 16)
Rstart
From Equations 10 - 12; it is possible to select Rstart:
4 (VDC − VCL ) < Rstart <
VDD − Rstart ⋅ IST
Accordingly, tstart can be controlled by adjusting the
value of Rstart and CVDD. For example, if VDC=311V,
Rstart=560k, CVDD=10µF, Ist=120µA, and VDDTH(ST+)=
13.5V, tstart is about 0.33s.
(EQ 12)
> R start
VDC − Rstart ⋅ IST − VDDTH (ST + )
In general, Equation 16 can be simplified as:
(EQ 11)
When the IC operates in shutdown mode due to thermal
protection, open-lamp protection, or hard-switching
protection, the IC consumes shutdown current, ISD,
which is larger than IST. To prevent restart during this
mode, Rstart must be selected to cover ISD current
consumption. The following equation must be satisfied:
ISD
(EQ 15)
From Equation 15, it is possible to calculate tstart by
substituting VDD(t) with VDDTH(ST+):
Assuming VDC=311V and VCL=15V, the minimum
resistance of Rstart is about 350kΩ.
VDC − VDDTH (ST + )
)
where CVDD is the total capacitance of the bypass
capacitors connected between VDD and GND.
Another important concern for choosing Rstart is the
available power rating of Rstart. To use a commercially
available, low-cost 1/4Ω resistor, Rstart must obey the
following rule:
(VDC
time
FAN7711 Rev. 1.00
VDC − VDDTH (ST + )
ISD
CVDD
CPH
(EQ 13)
GND
(2) For safe start-up with restart from shutdown mode:
VDC − VDDTH (ST + )
ISD
< Rstart <
VDC − VDDTH (ST + )
IST
FAN7711 Rev. 1.00
(EQ 14)
Figure 28. Equivalent Circuit During Start
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
13
FAN7711 Ballast Control Integrated Circuit
Design Guide
3. Lamp Turn-on Time
For the IC supply, the charge pump method is used in
Figure 29. Since CCP is connected to the half-bridge
output, the supplied current by CCP to the IC is
determined by the output voltage of the half-bridge.
The turn-on time of the lamp is determined by supply
build-up time tstart, preheating time, and ignition time;
where tstart has been obtained by Equation 17. When the
IC's supply voltage exceeds VDDTH(ST+) after turn-on or
restart, the IC operates in preheating mode. This
operation continues until CPH pin's voltage reaches ~3V.
In this mode, CPH capacitor is charged by IPH current,
as depicted in Figure 30. The preheating time is
achieved by calculating:
When the half-bridge output shows rising slope, CCP is
charged and the charging current is supplied to the IC.
The current can be estimated as:
I = CCP
V
dV
≈ CCP DC
dt
DT
(EQ 18)
where DT is the dead time and dV/dt is the voltage
variation of the half-bridge output.
t preheat = 3
When the half-bridge shows falling slope, CCP is
discharged through Dp2. Total supplied current, Itotal, to
the IC during switching period, t, is:
CPH
IPH
(EQ 21)
The preheating time is related to lamp life (especially
filament); therefore, the characteristics of a given lamp
should be considered when choosing the time.
(EQ 19)
Itotal = I ⋅ DT = CCP ⋅ VDC
VDD
From Equation 19, the average current, Iavg, supplied to
the IC is obtained by:
RT
IPH
CPH
Iavg =
Itotal CCP ⋅ VDC
=
= CCP ⋅ VDC ⋅ f
t
t
CPH
(EQ 20)
GND
FAN7711 Rev. 1.00
For the stable operation, Iavg must be higher than the
required current. If Iavg exceeds the required current, the
residual current flows through the shunt regulator
implemented on the chip, which can cause unwanted
heat generation. Therefore, CCP must be selected
considering stable operation and thermal generation.
Figure 30. Preheating Timer
Compared to the preheating time, it is almost impossible
to exactly predict the ignition time, whose definition is the
time from the end of the preheating time to ignition. In
general, the lamp ignites during the ignition mode.
Therefore, assume that the maximum ignition time is the
same as the duration of ignition mode, from 3V until CPH
reaches 5V. Thus, ignition time can be defined as:
For example, if CCP=0.5nF, VDC=311V, and f=50kHz, Iavg
is ~7.8mA; it is enough current for stable operation.
Charging mode
CCP
Dp1
To VDD
Idp1
Dp2
CVDD
tignition = (5 − 3 )
Discharging mode
CCP
Dp1
Idp1=0
Dp2
To VDD
CPH
CPH
=2
IIG
IIG
(EQ 22)
Note that, at ignition mode, CPH is charged by IIG, which
is six times larger than IPH. Consequently, total turn-on
time is approximately:
CVDD
f=1/t
VDC
VDD Build-Time + Preheating Time + Ignition Time =
DT:dead time
Half-bridge output
tignition = (5 − 3 )
CPH
CPH
=2
[Sec.]
IIG
IIG
(EQ 23)
Idp1
FAN7711 Rev. 1.00
Figure 29. Charge Pump Operation
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
14
FAN7711 Ballast Control Integrated Circuit
2. Current Supplied by Charge Pump
In addition, the ground return path of the timing
components (CPH, RT) and VDD decoupling capacitor
should be connected directly to the IC GND lead and not
via separate traces or jumpers to other ground traces on
the board. These connection techniques prevent highcurrent ground loops from interfering with sensitive
timing component operations and allow the control circuit
to reduce common-mode noise due to output switching.
Component selection and placement on PCB is important
when using power control ICs. Bypass the VCC to GND
as close to the IC terminals as possible with a low-ESR/
ESL capacitor, as shown in Figure 31. This bypassed
capacitor (CBP) can reduce the noise from the power
supply parts, such as start-up resistor and charge pump.
The signal GND must be separated from the power
GND. So, the signal GND should be directly connected
to the rectify capacitor using an individual PCB trace.
HOT
Cbp
RT
Cph
One point SGND
SGND
PGND
Figure 31. Preheating Timer
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
15
FAN7711 Ballast Control Integrated Circuit
4. PCB Guideline
Rectified
Waveform
D5
L2
VDC
D6
ZD 1
R1
D1
FUSE
C6
R3
R10
D2
R11
R4
NTC
TNR
L1
C1
C5
C3
R2
C2
1
INV
2
COMP
3
MOT
4
CS
C4
R6
D3
D4
R7
FAN7529
AC
INPUT
D7
VCC
8
OUT
7
GND
6
ZCD
5
D8
M1
R5
C8
C7
C9
C11
R13
R8
R12
C10
R9
Rectified
Waveform
L3
D50
R50
C55
D51
R51
Lamp
C56
R52
1
VDD
3 CPH
R53
C51
C50
C52
4 GND
FAN7711
2 RT
VB
8
HO
7
M2
R54
VS
6
LO
5
C53
D52
C54
L4
R55
C57
R56
M3
Lamp
R57
C58
FAN7711 Rev. 1.00
Figure 32. Application Circuit of 32W Two Lamps
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
16
FAN7711 Ballast Control Integrated Circuit
Typical Application Diagram
Part
Value
Note
Resistor
Part
Value
Note
C55
15nF/630V
Miller Capacitor
R1
330kΩ
1/2W
C56
2.7nF/1kV
Miller Capacitor
R2
750kΩ
1/4W
C57
15nF/630V
Miller Capacitor
R3
100Ω
1/2W
C58
2.7nF/1kV
Miller Capacitor
R4
20kΩ
1/4W
Diode
R5
47Ω
1/4W
D1
1N4007
1kV,1A
R6
10kΩ
1/4W
D2
1N4007
1kV,1A
R7
50kΩ
1/4W
D3
1N4007
1kV,1A
R8
47kΩ
1/4W
D4
1N4007
1kV,1A
R9
0.3Ω
1W
D5
UF4007
Ultra Fast,1kV,1A
R10
1MΩ
1/4W
D6
UF4007
Ultra Fast,1kV,1A
R11
1MΩ
1/4W
D7
1N4148
100V,1A
R12
12.6kΩ
1/4W,1%
D8
1N4148
100V,1A
R13
220kΩ
2W
D50
UF4007
Ultra Fast,1kV,1A
R50
150kΩ
1/4W
D51
UF4007
Ultra Fast,1kV,1A
R51
150kΩ
1/4W
D52
UF4007
Ultra Fast,1kV,1A
R52
150kΩ
1/4W
ZD1
IN4746A
Zener 18V, 1W
R53
90kΩ
1/4W,1%
R54
10Ω
1/4W
M1
FQPF5N60C
MOSFET
500V,6A
R55
47Ω
1/4W
M2
FQPF5N50C
500V,5A
R56
47kΩ
1/4W
M3
FQPF5N50C
500V,5A
R57
47Ω
1/4W
R58
47kΩ
1/4W
Fuse
3A/250V
Fuse
Capacitor
TNR
47nF/275VAC
Box Capacitor
C2
150nF/275VAC
Box Capacitor
C3
2200pF/3kV
Ceramic Capacitor
C4
2200pF/3kV
Ceramic Capacitor
C5
0.22µF/630V
Miller Capacitor
C1
C6
12nF/50V
Ceramic Capacitor
C7
22µF/50V
Electrolytic Capacitor
C8
39pF/50V
Ceramic Capacitor
C9
1µF/50V
Ceramic Capacitor
TNR
471
NTC
NTC
10D-09
Line Filter
LF1
40mH
Transformer
L1
0.94mH(75T:10T)
EI2820
Inductor
C10
0.1µF/50V
Ceramic Capacitor
L2
3.2mH(130T)
EI2820
C11
47µF/450V
Electrolytic Capacitor
L3
3.2mH(130T)
EI2820
C50
10µF/50V
Electrolytic Capacitor
C51
1µF/50V
Ceramic Capacitor
U1
FAN7711
Fairchild Semiconductor
C52
0.47µF/25V
Ceramic Capacitor,5%
U2
FAN7529
Fairchild Semiconductor
C53
100nF/50V
Ceramic Capacitor
C54
470pF/1kV
Ceramic Capacitor
IC
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
17
FAN7711 Ballast Control Integrated Circuit
Component List for 32W Two Lamps
Part
Value
Note
Part
Value
Resistor
Note
Diode
R1
470kΩ
1/4W
D1
1N4007
1kV/1A
R2
90kΩ
1/4W
D2
1N4007
1kV/1A
R3
10Ω
1/4W
D3
1N4007
1kV/1A
R4
47Ω
1/4W
D4
1N4007
1kV/1A
R5
47Ω
1/4W
D5
UF4007
1kV/1A,Ultra Fast
D6
UF4007
1kV/1A,Ultra Fast
D7
UF4007
1kV/1A,Ultra Fast
Capacitor
C1
22µF/250V
Electrolytic Capacitor
Inductor
C2
10µF/50V
Electrolytic Capacitor
C3
470nF/25V
Miller Capacitor
C4
100nF/25V
Miller Capacitor
Q1
FQPF1N50C
500V,1A
C5
470pF/630V
Miller Capacitor
Q2
FQPF1N50C
500V,1A
C6
33nF/630V
Miller Capacitor
C7
3.3nF/1kV
Miller Capacitor
L1
2.5mH (280T)
EE1616S
MOSFET
IC
U1
FAN7711
Fairchild Semiconductor
Note:
3. Refer to the typical application circuit provided in Figure 1.
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
18
FAN7711 Ballast Control Integrated Circuit
Component List for 20W CFL
FAN7711 Ballast Control Integrated Circuit
Package Dimensions
8-SOP
Dimensions are in millimeters unless otherwise noted.
Figure 33. 8-Lead Small Outline Package (SOP)
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
19
FAN7711 Ballast Control Integrated Circuit
Package Dimensions
8-DIP
Dimensions are in inches and [millimeters] unless otherwise noted.
Figure 34. 8-Lead Dual In-Line Package (DIP)
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
20
®
ACEx
Across the board. Around the world.¥
ActiveArray¥
Bottomless¥
Build it Now¥
CoolFET¥
CorePLUS¥
CROSSVOLT¥
CTL™
Current Transfer Logic™
DOME¥
2
E CMOS¥
®
EcoSPARK
EnSigna¥
FACT Quiet Series™
®
FACT
®
FAST
FASTr¥
FPS¥
®
FRFET
GlobalOptoisolator¥
GTO¥
HiSeC¥
i-Lo¥
ImpliedDisconnect¥
IntelliMAX¥
ISOPLANAR¥
MICROCOUPLER¥
MicroPak¥
MICROWIRE¥
Motion-SPM™
MSX¥
MSXPro¥
OCX¥
OCXPro¥
®
OPTOLOGIC
®
OPTOPLANAR
PACMAN¥
PDP-SPM™
POP¥
®
Power220
®
Power247
PowerEdge¥
PowerSaver¥
Power-SPM¥
®
PowerTrench
Programmable Active Droop¥
®
QFET
QS¥
QT Optoelectronics¥
Quiet Series¥
RapidConfigure¥
RapidConnect¥
ScalarPump¥
SMART START¥
®
SPM
STEALTH™
SuperFET¥
SuperSOT¥-3
SuperSOT¥-6
SuperSOT¥-8
SyncFET™
TCM¥
®
The Power Franchise
TinyBuck¥
®
TinyLogic
TINYOPTO¥
TinyPower¥
TinyWire¥
TruTranslation¥
PSerDes¥
®
UHC
UniFET¥
VCX¥
Wire¥
™
TinyBoost¥
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS
HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE
APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS
PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S
WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body or
(b) support or sustain life, and (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in a significant injury of the user.
2. A critical component in any component of a life support,
device, or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Advance Information
Formative or In Design
This datasheet contains the design specifications for product
development. Specifications may change in any manner without notice.
Definition
Preliminary
First Production
This datasheet contains preliminary data; supplementary data will be
published at a later date. Fairchild Semiconductor reserves the right to
make changes at any time without notice to improve design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild Semiconductor
reserves the right to make changes at any time without notice to improve
design.
Obsolete
Not In Production
This datasheet contains specifications on a product that has been
discontinued by Fairchild Semiconductor. The datasheet is printed for
reference information only.
Rev. I27
© 2007 Fairchild Semiconductor Corporation
FAN7711 Rev. 1.0.3
www.fairchildsemi.com
21
FAN7711 Ballast Control Integrated Circuit
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an
exhaustive list of all such trademarks.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com