Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FL7733A
带功率因数校正的初级端调节 LED 驱动器
特性
描述
性能
FL7733A 是一款采用先进的初级端调节 (PSR) 技术的高
度集成式 PWM 控制器,能够尽可能减少中低功率 LED
照明转换器中的元件。
所有条件下的总恒流容差小于 ±3%
通用线路电压范围内的变动小于 ±1%
50% - 100% 负载电压变化小于 ±1%
±20% 电感变化小于 ±1%
初级端调节控制无需大容量输入电容和次级反馈电
路,即可实现具有成本效益的解决方案
应用输入电压范围:80 VAC - 308 VAC
使用带 VDD 调节的内部高压启动实现快速启动
(85 VAC 下,启动时间小于 200 ms)
通过自适应反馈回路控制,实现无过冲启动
通用线路输入范围内的高 PF(大于 0.9)和低
THD(小于 10%)
FL7733A 通过尽可能减小导通时间波动,在通用线路范
围内实现高功率因数和低 THD。采用一个集成式高电压
启动电路实现快速启动和高系统效率。在启动期间,通过
自适应反馈环路控制,预测稳态状况并设置接近于稳态的
初始反馈状况,从而避免出现 LED 电流过高或过低。
FL7733A 还提供多种强大的保护功能,如 LED 短路/开
路、输出二极管短路、检测电阻短路/开路、以及过温保
护,从而实现较高的系统可靠性。
FL7733 控制器采用 8 引脚小尺寸封装 (SOP)。
系统保护
该 LED 驱动器利用创新型 TRUECURRENT® 技术实现
严格的恒流输出,从而使通用线路电压范围内恒流 (CC)
容差小于 ±1% 的设计满足严苛的 LED 亮度要求。
LED 短路/开路保护
相关产品资源
输出二极管短路保护
检测电阻短路/开路保护
FL7733A 产品文件夹
VDD 过压保护 (OVP)
VDD 欠压锁定 (UVLO)
过温保护 (OTP)
所有保护功能都是在自动重启 (AR) 模式下实现
逐周期限流
应用
5 W 至大于 60 W 的低功率至中等功率 LED 照明系
统兼容模拟调光功能
订购信息
器件编号
工作温度范围
封装
包装方法
FL7733AMX
-40°C 至 +125℃
8 引脚小尺寸封装 (SOP-8)
卷带和卷盘
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
www.fairchildsemi.com
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
2014 年 11 月
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
应用框图
DC Output
AC Input
2
8
HV
GATE
6 COMI
CS
1
VDD 4
3 GND
NC
VS 5
7
图 1.
典型应用
框图
Shutdown
HV
Max. Duty
Controller
8
250 ms
Timer
Gate Driver
S
EAV
Q
+
VDD
4
R
VDD
Good
+
SRSP
Monitor
1
CS
6
COMI
5
VS
SRSP
VCS-CL
+
VOVP
GATE
OCP
1.35 V
Current Limit
Control
2
+
0.1 V
-
VDD
OVP
+
+
LEB
Sawtooth
Generator
Internal
Bias
OSC
3
EAI
Q
Error
Amp.
R
SLP
OCP
VDD Good
OTP
SRSP
VS OVP
N.C
VREF
tDIS
Detector
Line
Compensator
TRUECURRENT®
Calculation
3V
+
VS OVP
DCM
Controller
+
GND
S
7
EAV
SLP
Monitor
+
SLP
图 2.
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
Sample & Hold
0.3 V
功能框图
www.fairchildsemi.com
2
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
F:Fairchild 徽标
Z:工厂代码
X:一位数字年份代码
Y:一位数字周代码
TT:两位数字模具运行代码
T: 封装类型 (M=SOP)
M:制造流代码
4
3
标识信息
4
3
ZXYTT
7733A
TM
图 3.
顶标
引脚配置
CS
1
8
HV
GATE
2
7
NC
GND
3
6
3
COMI
VDD
4
5
4
VS
图 4.
引脚配置(俯视图)
引脚描述
引脚号
名称
描述
1
CS
电流感测。此引脚连接了一个电流检测电阻来检测 MOSFET 电流,从而实现恒流输出电流调节。
2
栅极
PWM 信号输出。此引脚采用内部图腾柱输出驱动器,用于驱动功率 MOSFET。
3
GND
接地
4
VDD
电源。IC 工作电流和 MOSFET 驱动电流均通过此引脚提供。
5
VS
6
COMI
7
NC
未连接
8
HV
高压。该引脚通过电阻连接整流输入。
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
电压检测。该引脚检测输出电压和放电时间,为 CC 调节提供信息。此引脚通过电阻分压器与变压
器辅助绕组相连。
恒流环路补偿。此引脚与 COMI 和 GND 之间的电容相连,补偿电流环路增益。
www.fairchildsemi.com
3
应力超过绝对最大额定值,可能会损坏器件。在超出推荐的工作条件的情况下,该器件可能无法正常工作,所以不建议
让器件在这些条件下长期工作。此外,长期在高于推荐的工作条件下工作,会影响器件的可靠性。绝对最大额定值仅是
应力规格值。
符号
HV
参数
最小值 最大值
HV 引脚电压
(1,2)
单位
700
V
30
V
VVDD
直流电源电压
VVS
VS 引脚输入电压
-0.3
6.0
V
VCS
CS 引脚输入电压
-0.3
6.0
V
VCOMI
COMI 引脚输入电压
-0.3
6.0
V
VGATE
GATE 引脚输入电压
-0.3
30.0
V
PD
功耗 (TA<50℃)
633
mW
TJ
最大结温
150
℃
150
℃
260
℃
TSTG
TL
存储温度范围
-55
引脚温度(焊接)10 秒
注意:
1. 若应力超过绝对最大额定值中所列的数值,可能会给器件造成不可修复的损坏。
2. 测得的所有电压,除差分电压之外,都以 GND 引脚为参考点。
热阻测试
除非另有说明,TA=25℃。
符号
参数
数值
单位
JA
节-环境之间热阻
158
℃/W
JC
结壳热阻
39
℃/W
数值
单位
注意:
3. 参考 JEDEC 建议环境,JESD51-2 和测试板,JESD51-3,1S1P 具有最小焊盘布局。
静电放电 (ESD) 能力
符号
ESD
参数
人体模型,ANSI/ESDA/JEDEC JS-001-2012
5
元件充电模型,JESD22-C101
2
kV
注意:
4. 符合 JEDEC 标准 JESD22-A114 和 JESD 22-C101。
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
www.fairchildsemi.com
4
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
绝对最大额定值
除非另有说明,VDD=15 V,TJ=-40 至 +125℃。定义电流流入器件为正值,流出器件为负。
符号
参数
工作条件
最小值 典型值 最大值
单位
VDD-ON
导通阈值电压
14.5
16.0
17.5
V
VDD-OFF
关断阈值电压
6.75
7.75
8.75
V
3
4
5
mA
30
50
μA
24
25
V
1.5
V
IDD-OP
工作电流
CL=1 nF,f=fMAX-CC
IDD-ST
启动电流
VDD=VDD-ON–1.6 V
VVDD-OVP
VDD 过压保护水平
23
栅极部分
VOL
输出低电平
TA=25℃, VDD=20 V,
IDD_GATE=1 mA
VOH
输出高电平
TA=25℃, VDD=10 V,
IDD=1 mA
ISOURCE
峰值源电流
(5)
VDD=10 ~ 20 V
-60
mA
ISINK
峰值吸电流
(5)
VDD=10 ~ 20 V
180
mA
5
V
tR
上升时间
TA=25℃, VDD=15 V,
CLOAD =1 nF
100
150
200
ns
tF
下降时间
TA=25℃, VDD=15 V,
CLOAD=1 nF
20
60
100
ns
输出箝位电压
VDD=20 V, VCS=0 V,
VVS=0 V, VCOM=0 V
12
15
18
V
源自 HV 引脚的电源电流
TA=25℃, VIN=90 VAC,
VDD=0 V
9
mA
1
10
μA
190
250
310
ms
VCLAMP
HV启动部分
IHV
IHV-LC
启动后的漏电流
tR-JFET
启动后的 JFET 调节时间
(5)
TA=25℃
VJFET-HL
JFET 调节电压上限
17.5
19.0
20.5
V
VJFET-LL
JFET 调节电压下限
11.5
13.0
14.5
V
TA=25℃
11
17
23
μmho
电流-误差-放大器部分
gM
跨导
(5)
ICOMI-SINK
COMI 灌电流
TA=25℃, VEAI=2.55 V,
VCOMI=5 V
12
18
24
μA
ICOMI-SOURCE
|COMI 源电流|
TA=25℃, VEAI=0.45 V,
VCOMI=0 V
12
18
24
μA
VCOMI-HGH
COMI 高电平
VEAI=0 V
4.7
VCOMI-LOW
COMI 低电平
VEAI=5 V
VCOMI_INT.CLP
tCOMI_INT.CLP
V
0.1
V
初始 COMI 箝位电压
(5)
1.2
V
初始 COMI 箝位时间
(5)
15
ms
接下页
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
www.fairchildsemi.com
5
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
电气特性
除非另有说明,VDD=15 V,TJ=-40 至 +125℃。定义电流流入器件为正值,流出器件为负。
符号
参数
工作条件
最小值 典型值 最大值
单位
电压感测部分
(5)
0.85
1.15
1.45
μs
VS:VS 消隐电流
-75
-90
-105
μA
VS:输出过压保护电平
2.95
3.00
3.15
V
tDIS-BNK
tDIS:VS
IVS-BNK
VVS-OVP
消隐时间
VS:使能低电平限流的阈值电压
(5)
0.25
0.30
0.35
V
VVS-HIGH-CL-DIS
VS:禁用低电平限流的阈值电压
(5)
0.54
0.60
0.66
V
VVS-SLP-TH
VS:输出短路 LED 保护阈值电压
0.25
0.30
0.35
V
VVS-LOW-CL-EN
tSLP-BNK
VS:启动后检测禁用时间
(5)
TA=25℃
15
ms
电流检测部分
VRV
参考电压
TA=25℃
1.485
(5)
1.500
1.515
V
tLEB
前沿消隐时间
tMIN
CC 最低导通时间
tPD
到栅极输出端的传播延迟
50
100
150
ns
VCS-HIGH-CL
限流阈值上限
0.9
1.0
1.1
V
VCS-LOW-CL
限流阈值下限
0.16
0.20
0.24
V
(5)
VCOMI=0 V
(5)
tLOW-CM
启动时的低电流模式工作时间
VCS-SRSP
检测电阻短路保护的 VCS 阈值电压
VCS-OCP
过流保护的 VCS 阈值电压
VCS / IVS
线路补偿电压和 VS 电流
(5)
300
ns
500
ns
20
TA=25℃
1.20
的关系
1.35
ms
0.1
V
1.50
V
21.5
V/A
振荡器部分
fMAX-CC
恒流最大频率
TA=25℃, VS=3.0 V
65
70
75
kHz
fMIN-CC
恒流最小频率
TA=25℃, VS=0.3 V
23.0
26.5
30.0
kHz
tON-MAX
最大导通时间
TA=25℃, f=fMAX-CC
11.0
13.0
15.0
μs
过温保护部分
TOTP
TOTP-HYS
OTP 阈值温度
重启结温滞回
(5)
(5)
150
℃
10
℃
注意:
5. 这些参数尽管通过设计得到保证,但未经过生产测试。
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
www.fairchildsemi.com
6
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
电气特性(续)
1.5
1.3
1.3
Normalized
Normalized
1.5
1.1
0.9
0.7
1.1
0.9
0.7
0.5
0.5
-40
-20
0
25
50
75
100
125
-40
-20
0
Temperature (℃)
VDD-ON 与温度的关系
图 6.
1.5
1.5
1.3
1.3
Normalized
Normalized
图 5.
1.1
0.9
0.7
50
75
100
125
100
125
100
125
VDD-OFF 与温度的关系
1.1
0.9
0.7
0.5
0.5
-40
-20
0
25
50
75
100
125
-40
-20
0
Temperature (℃)
图 7.
25
50
75
Temperature (℃)
IDD-OP 与温度的关系
图 8.
1.5
1.5
1.3
1.3
Normalized
Normalized
25
Temperature (℃)
1.1
0.9
0.7
VDD-OVP 与温度的关系
1.1
0.9
0.7
0.5
0.5
-40
-20
0
25
50
75
100
125
-40
Temperature (℃)
图 9.
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
-20
0
25
50
75
Temperature (℃)
fMAX-CC 与温度的关系
图 10. fMIN-CC 与温度的关系
www.fairchildsemi.com
7
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
典型性能特征
1.5
1.3
1.3
Normalized
Normalized
1.5
1.1
0.9
0.7
1.1
0.9
0.7
0.5
0.5
-40
-20
0
25
50
75
100
125
-40
-20
0
Temperature (℃)
50
75
100
125
100
125
100
125
图 12. Gm 与温度的关系
1.5
1.5
1.3
1.3
Normalized
Normalized
图 11. VVR 与温度的关系
1.1
0.9
0.7
1.1
0.9
0.7
0.5
0.5
-40
-20
0
25
50
75
100
125
-40
-20
0
Temperature (℃)
25
50
75
Temperature (℃)
图 13. ICOMI-SOURCE 与温度的关系
图 14. ICOMI-SINK 与温度的关系
1.5
1.5
1.3
1.3
Normalized
Normalized
25
Temperature (℃)
1.1
0.9
0.7
1.1
0.9
0.7
0.5
0.5
-40
-20
0
25
50
75
100
125
-40
Temperature (℃)
0
25
50
75
Temperature (℃)
图 15. VVS-OVP 与温度的关系
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
-20
图 16. VCS-OCP 与温度的关系
www.fairchildsemi.com
8
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
典型性能特征(接上页)
FL7733A 为交流-直流 PWM 控制器,适用于 LED 照明
®
应用。TRUECURRENT 技术能够精确调节恒定 LED 电
流,不依赖于输入电压、输出电压和电感量的变化。振荡
器中的 DCM 控制能够减少导通损耗,保持 DCM 在宽范
围输出电压下运行,在单级反激式或降压-升压拓扑中实
现高功率因数校正。LED 短路/开路保护、检测电阻短路/
开路保护、过流保护、过温保护和逐周期限流等一系列措
施能够使系统稳定运行,保护外部元器件。
VDD = VDD_ON
VIN
High Line
Low line
Current Mode
VCS
Voltage Mode
0.2 V
VCOMI
Low line
High Line
启动
1.0 V
启动时,内部高压 JFET 提供启动电流和 VDD 电容充电
电流,如图 17 所示。当 VDD 达到 16 V 时,开关操作开
始,内部高压 JFET 继续提供 VDD 工作电流,该电流初
始持续时间为 250 ms,可保持 VDD 电压高于 VDD-OFF。
随着输出电压的增加,辅助绕组开始成为 VDD 电流的主
要来源。
15 ms
ILED
Time
图 18. 启动顺序
PFC 与 THD
VDC
RVS1
在反激式或降压-升压拓扑中,以恒定的导通时间和频率
在 非 连续 导通 模式 (DCM) 下 工 作可 实现 高 PF 和 低
THD,如图 19 所示。恒定导通时间通过内部误差放大器
和 COMI 引脚上的外部 COMI 大电容(一般超过 1 µF)
得以保持。恒定频率和 DCM 操作通过 DCM 控制来管
理。
CVDD
RVS2
HV
VDD
8
4
Primary current
peak envelope
VS
250 ms
Timer
Internal
Bias
Startup Time 20 ms
5
Secondary current
peak envelope
Average
input current
VDD Good
16 V /
7.75 V
图 17. 启动框图
在 VDD-ON 之后的 20 ms 内可通过电流模式控制开关。
采用反激式或降压-升压拓扑进行电流模式开关期间,输
出电流仅由输出电压确定。因此,输出电压以恒定的斜率
增加,而无论线路电压如何变动。 短路 LED 保护 (SLP)
在 15 ms SLP 消隐时间之后使能,因此输出电压高于
SLP 阈值电压,并且在无 SLP 的一般条件下保证顺利启
动。
Constant tON
Constant tOFF
图 19. 功率因数校正
恒定电流调节
由于输出电流与稳态时二极管平均电流相等,因此可以通
过峰值漏电流和电感电流放电时间来估算输出电流。峰值
漏极电流由 CS 峰值电压检测器确定。电感电流放电时间
(tDIS) 由 tDIS 检测器检测。有了峰值漏电流、电感电流放
电时间和操作开关周期信息,TRUECURRENT® 计算模
块便可如下所示估算输出电流:
1 t
1
I o DIS VCS nPS
2 tS
RS
在电流模式开关期间,用于确定电压模式下的导通时间的
COMI 电压将调节至接近稳态电平。COMI 电容充电至
1.2 V(持续 15 ms),并调节至与 VIN 峰值成反比的调
制电平(持续 5 ms)。20 ms 启动时间之后的开启时间
可控制在接近稳态导通时间的水平上,以便平滑进入电压
模式而不产生 LED 电流过冲或欠冲。
t DIS
VCS 0.25
tS
Io 0.125
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
nPS
RS
www.fairchildsemi.com
9
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
功能说明
Ipk =
Gate
Driver
RS
GATE
CC
Control
OSC
VCS
2
ID.pk
VOUT
tDIS
Detector
IO
5
DCM
Controller
ID
IDS
VF ·
Vo ·
Na
Ns
S/H
图 21. DCM 和 BCM 控制
Na
Ns
Ipk
Ipk
Ipk Tdis
T
T
3
n Vo
4
Lm
tDIS
tS
Iavg
nVo
Lm
Tdis
tON
VS
Iavg
Ipk 4 / 3 Tdis
4 / 3T
图 20. 初级端调节主要波形
4
T
3
4
Tdis
3
计算所得输出电流与内部精确基准电压进行比较,生成误
差电压 (VCOMI),可确定 MOSFET 在电压模式控制下的
导通时间。凭借 Fairchild 创新型 TRUECURRENT® 技
术,恒流输出可得到精确控制。尽管输出电流是通过准确
方法计算的,但是由于高 Qg 造成的 MOSFET 的关断传
播延迟,高输入电压下的输出电流仍然可能大于低输入电
压下的输出电流。要保持整个输入电压范围内的严格 CC
调节,可在 CS 引脚和 MOSFET 的源极之间接入 100 ~
500 的线路补偿电阻。跨补偿电阻的电压取决于用于
MOSFET 导通的 CS 引脚中流出的电流,且该电压与输
入电压成正比。
3
n Vo
5
Lm
Ipk
5
Tdis
3
Iavg
Ipk 5 / 3Tdis
5 / 3T
5
T
3
图 22. 初级电流和次级电流
BCM 控制
次级二极管导通时间可能在 DCM 控制所设定的开关周期
结束以后才结束。在此情况下,下一个开关周期在次级二
极 管 导 通 时 间 结 束 时 开 始 , 因 为 FL7733A 不 允 许
CCM。因此,工作模式将从 DCM 切换至临界导通模式
(BCM)。
DCM 控制
如上所述,在反激式拓扑中,为了获得较高的功率因数,
DCM 必 须 得 到 保 证 。 为 了 在 宽 输 出 电 压 范 围 内 保 持
DCM,在线性频率控制下,开关频率需根据整个 Vs 范围
内的输出电压进行线性调节。输出电压由辅助绕组和连接
VS 引脚的分压电阻检测,如图 21 所示。当输出电压降
低时,次级二极管导通时间增加,并且 DCM 控制延长开
关周期,以便在宽输出电压范围内保持 DCM,如图 22
所示。在满载条件下,频率控制还会降低初级 RMS 电
流,从而获得更佳功效。
模拟调光功能
模拟调光功能可通过控制用于确定主电源 MOSFET 的导
通时间的 COMI 电压执行。图 23 所示示例为使用光电耦
合器的 FL7733A 的模拟调光电路,因此 LED 电流可通
过来自隔离变压器的次级端的调光信号 A-Dim 控制。
COMI
VDC
ICOMI
CCOMI
A-Dim Signal
(0 ~ VDC)
图 23. 模拟调光信号
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
www.fairchildsemi.com
10
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
其中,nPS 是初级与次级的匝数比,而 RS 是
MOSFET 源端与接地之间的检测电阻。
19 V /
13 V
250 ms
Timer
VDD
Good
VDD OVP
VDD-OVP
EAV
250 ms
Timer
4 VDD
VOUT
S/H
SLP
LED Open
VDD-OVP x Ns
Na
16 V /
7.75 V
15 ms
Timer
5 VS
S/H
VS-OVP
图 26. 内部过压保护模块
+
SLP is disabled
for initial 15 ms
16 V /
7.75 V
HV
VS OVP
VDD
Good
4 VDD
-
+
VDD
+
19 V /
13 V
+
8
8 HV
-
VDD
在短路 LED 条件下,次级二极管受高电流应力影响。当
VS 电压由于短路 LED 条件而低于 0.3 V 时,逐周期限流
电平从 1.0 V 变为 0.2 V,同时触发 SLP 如果 VS 电压低
于 0.3 V 并持续四个连续开关周期。图 24 和图 25 显示
LED 短路条件下的 SLP 模块和工作波形。考虑到系统安
全性,如需在保护条件下设置足够的自动重启时间,那么
可将 VDD 保持在 13 V 至 19 V 之间(也就是 UVLO 以
上)并在 VDD-ON 之后持续 250 ms。SLP 在初始 15 ms
内禁用,以确保在通常 LED 条件下顺利启动。
5
VS
EAV
3V
0.3 V
图 24. 内部 SLP 模块
VIN
VDD
VDD-OVP
LED short
19 V
VDD ON
13 V
VDD OFF
250 ms JFET regulation
Gate
VCS
0.2 V
图 27. LED 开路条件下的波形
VDD
19 V
检测电阻短路保护 (SRSP)
13 V
在检测电阻短路条件下,VCS 电平几乎为零,逐脉冲限流
或 OCP 无效。FL7733A 专门用于提供检测电阻短路保
护,可同时用于电流和电压模式操作。如果在第一个开关
周期中,VCS 电平低于 0.1 V,则电流模式 SRSP 停止栅
极输出。20 ms 启动时间之后,电压模式 SRSP 关断
栅极(如果 VCS 电平在超过峰值 VIN 60% 的情况下不足
0.1 V 的话)。
VDD-ON
VDD OFF
250 ms JFET regulation
Gate
15 ms
15 ms
图 25. 短路 LED 条件下的波形
欠压锁定 (UVLO)
开路 LED 保护
VDD 导通和关断阈值分别内部固定为 16 V 和 7.75 V。启
动时,VDD 电容必须利用高压 JFET 充电至 16 V,才能
开启 FL7733A。VDD 电容持续为 VDD 供电,直到主变压
器的辅助绕组提供辅助电源。在启动过程中,应保持VDD
高于 7.75 V。因此,VDD 电容必须适中,才能将 VDD 保
持在 UVLO 阈值之上,直到辅助绕组电压超过 7.75 V。
FL7733A 可在开路 LED 条件下保护外部元器件,如输出
二极管和输出电容。开关关断期间,施加反映输出电压,
作为辅助绕组电压。由于 VDD 和 VS 电压在辅助绕组上具
有输出电压信息,VDD 和 VS 引脚上的内部电压比较器
可触发输出过压保护 (OVP),如图 26 和图 27 所示。
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
www.fairchildsemi.com
11
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
短路 LED 保护 (SLP)
当输出二极管或次级绕组短路时,具有极高 di/dt 的开关
电流可流经 MOSFET,哪怕导通时间极短。FL7733A 专
门用于保护系统,使其免受该过量电流的损害。当检测电
阻上的 CS 电压高于 1.35 V,OCP 比较器输出会停止栅
极的开关动作。
过温保护 (OTP)
如果结温超过 150℃,温度感测电路将关断 PWM 输出。
OTP 触发后的滞回温度为 10℃。
PCB 布局指南
电源转换器 PCB 布局的重要性等同于电路设计,因为高
寄生电感或电阻的 PCB 布局会产生大量开关噪声,使系
统不稳定。PCB 的设计应在最大程度上限制进入控制信
号的开关噪声。
1.
信号地和电源地应分开,并且只能在一个位置上相连
(GND 引脚),避免接地环路噪声。从整流桥二极
管到检测电阻的电源接地路径应短而宽。
2.
栅极驱动电流路径 (GATE – RGATE – MOSFET –
RCS – GND) 应尽可能短。
3.
控制引脚元件(如 CCOMI、CVS 和 RVS2)位置应靠近
各自所分配的引脚以及信号地。
4.
与 MOSFET 漏极与 RCD 缓冲器有关的高压走线应
远离控制电路,以避免不必要的干扰。
5.
如果散热片用于 MOSFET,则将此散热片连接到电
源接地。
6.
辅助绕组接地应比控制引脚元件的接地更靠近 GND
引脚。
DC Output
AC Input
Power
ground
5
RCS
2
RGATE
4
FL7733A
CS
HV
GATE
NC
CCOMI
1
GND COMI
CVS
VDD
VS
3
RVS2
CVDD
6
RVS1
Signal
ground
图 28. 布局示例
© 2014 飞兆半导体公司
FL7733AMX • 修订版 1.2
www.fairchildsemi.com
12
FL7733A — 带功率因数校正的初级端调节 LED 驱动器
在检测电阻开路条件下,检测电阻电压无法检测,输出电
流调节不正确。若检测电阻开路受损,则 CS 引脚上的寄
生电容由内部 CS 电流源进行充电。因此,VCS 电平上升
至 OCP 阈值电压,然后立即停止开关动作。
过流保护 (OCP)
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com