Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FLS0116
MOSFET Integrated Smart LED Lamp Driver IC with
PFC Function
Features
Description
The FLS0116 LED lamp driver is a simple IC with
integrated MOSFET and PFC function. The special
“adopted digital” technique automatically detects input
voltage condition and sends an internal reference signal
to achieve high power factor. When AC input is applied
to the IC, the PFC function is automatically enabled.
When DC input is applied to the IC, the PFC function is
automatically disabled. The FLS0116 does not need a
bulk (electrolytic) capacitor for supply rail stability, which
significantly improves LED lamp life.
Built-in MOSFET(1 A / 550 V)
Digitally Implemented Active-PFC Function
No Additional Circuit for Achieving High PF
Application Input Range: 80 VAC ~ 308 VAC
Built-In HV Supplying Circuit: Self Biasing
AOCP Function with Auto-Restart Mode
Built-In Over-Temperature Protection (OTP)
Cycle-by-Cycle Current Limit
Current Sense Pin Open Protection
Low Operating Current: 0.85 mA (Typical)
Under-Voltage Lockout with 5 V Hysteresis
Programmable Oscillation Frequency
Programmable LED Current
Analog Dimming Function
Soft-Start Function
Precise Internal Reference: ±3%
Applications
L1
LED
D1
L3
FLS0116
Fuse
CS
DRAIN
BD
C1
VCC
C2
HV
GND
RT
R1
ADIM
C3
C4
R2
L2
Figure 1. Typical Application
LED Lamp for Decorative Lighting
LED Lamp for Low-Power Lighting Fixture
Ordering Information
Part Number
Operating
Temperature Range
FLS0116MX
-40°C to +125°C
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
Package
7-Lead, Small-Outline Integrated Circuit (SOIC),
JEDEC MS-012, .150-inch, Narrow Body
Packing Method
Tape & Reel
www.fairchildsemi.com
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
June 2013
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Block Diagram
VCC
2
JFET
VCC
7 HV
ZCD
UVLO
time
IAD
ADIM
8 DRAIN
ZCD
5
DAC
Soft-Start
TSD
Digital Block
RT
4
Oscillator
R
-
Q
S
Reference
+
1 CS
LEB
GND
Leading-Edge
Blanking
3
FLS0116
+
AOCP
2.5V
Figure 2. Block Diagram
Pin Configuration
DRAIN
FLS0116
CS
VCC
GND
HV
ADIM
RT
Figure 3. Pin Configuration
Pin Definitions
Pin #
Name
Description
1
CS
Current Sense. Limits output current, depending on the sensing resistor voltage. The CS pin is
also used to set the LED current regulation.
2
VCC
VCC. Supply pin for stable IC operation; ZCD signal detection used for accurate PFC function.
3
GND
GROUND. Ground for the IC
4
RT
5
ADIM
7
HV
8
DRAIN
RT. Programmable operating frequency using an external resistor; the IC has pre-fixed
frequency when this pin is open or floating.
Analog Dimming. Connect to the internal current source. Use to change the output current
using an external resistor. If ADIM is not used, connect a 0.1 µF bypass capacitor between the
ADIM and GND.
High Voltage. Connect to the high-voltage line and supply current to the IC.
DRAIN. The drain pin of internal MOSFET
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
2
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device
reliability. The absolute maximum ratings are stress ratings only.
Symbol
Parameter
Min.
Max.
Unit
VCC
IC Supply Voltage
20
V
HV
High Voltage Sensing
550
V
DRAIN
Internal Drain Voltage
550
V
Analog Dimming
5
V
VADIM
VRT
RT Pin Voltage
5
V
VCS
Allowable Current Sensing Detection Voltage
5
V
TA
Operating Ambient Temperature Range
-40
+125
C
TJ
Operating Junction Temperature
-40
+150
C
-65
+150
C
135
C/W
660
mW
TSTG
Storage Temperature Range
θJA
Thermal Resistance Junction-Air
PD
Power Dissipation
ESD
(1,2)
Electrostatic Discharge Capability
Human Body Model, JESD22-A114
2000
Charged Device Model, JESD22-C101
1000
V
Notes:
1. Thermal resistance test board. Size: 76.2 mm x 114.3 mm x 1.6 mm (1S0P); JEDEC standard: JESD51-2, JESD513.
2. Assume no ambient airflow.
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
3
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Absolute Maximum Ratings
Typical values are at TA = +25°C. Specifications to -40°C ~ 125°C are guaranteed by design based on final
characterization results.
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
VCC Bias Section
VCC Regulator Output Voltage
VHV=100 VDC
14.0
15.5
17.0
V
VCCST+
VCC
UVLO Positive-Going Threshold
VCC Increasing
12
13
14
V
VCCST-
UVLO Negative-Going Threshold
VCC Decreasing
7
8
9
V
VCCHYS
UVLO Hysteresis
4
5
6
V
0.85
1.20
mA
120
150
μA
IHV
HV Pin Current
IST
Startup Current
VHV=100 VDC, RT=Open
Switching Section
fOSC
tMIN
DMAX
Operating Frequency
Minimum On Time
RT=5.95 kΩ
200
250
300
kHz
RT=87 kΩ
16
20
24
kHz
RT Open
40.5
45.0
49.5
kHz
(3)
Maximum Duty Cycle
tLEB
Leading Edge Blanking Time
VRT
Voltage Reference of RT Pin
(3)
400
ns
50
%
350
ns
1.5
V
Soft-Start Section
tss
Soft-Start Time
DC Mode
(3)
48
AC Mode
60
72
ms
7
Periods
Reference Section
VCS1
Internal Reference Voltage of CS Pin
VCS2
DC Mode
AC Mode
(3)
0.354
0.365
0.376
0.485
0.500
0.515
17.7
18.7
19.7
V
Protection Section
OVPVCC
VAOCP
Over-Voltage Protection on VCC Pin
Abnormal OCP Level at CS Pin
(3)
2.5
(3)
tAOCP
Abnormal Detection Time
TTSDH
Thermal Shutdown Threshold
TTSDHY
Thermal Shutdown Threshold
(3)
Hysteresis
(3)
140
Dimming Section
Analog Dimming Positive Going
VADIM(ST+)
(3)
Threshold
Analog Dimming Negative Going
VADIM(ST-)
(3)
Threshold
IAD
3.15
Internal Current Source for ADIM Pin
9
V
V
70
ns
150
°C
50
°C
3.50
3.85
V
0.50
0.75
V
12
15
μA
Continued on the following page…
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
4
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Electrical Characteristics
Typical values are at TA = +25°C. Specifications to -40°C ~ 125°C are guaranteed by design based on final
characterization results.
Symbol
Parameter
Condition
Min.
VCC=0 V, ID=250 μA
550
Typ.
Max.
Unit
250
μA
10.0
Ω
MOSFET Section
BVDSS
Breakdown Voltage
ILKMOS
Internal MOSFET Leakage Current VDS=550 VDC, VGS=0 V
RON(ON)
Drain-Source On Resistance
CISS
COSS
Input Capacitance
(3)
(3)
Output Capacitance
(3)
CRSS
Reverse Transfer Capacitance
td(ON)
Turn-On Delay
tr
td(OFF)
tf
(3)
Rise Time
(3)
(3)
Turn-Off Delay
Fall Time
(3)
(3)
V
VGS=10 V, VDGS=0 V,
TC=25°C
7.3
VGS=0 V,VDS=25 V, f=1 MHz
135
pF
VGS=0 V,VDS=25 V, f=1 MHz
21
pF
VGS=0 V,VDS=25 V, f=1 MHz
3.2
pF
VDD=350 V, ID=1 A
10
ns
VDD=350 V, ID=1 A
13.4
ns
VDD=350 V, ID=1 A
14.9
ns
VDD=350 V, ID=1 A
36.8
ns
Note:
3. These parameters, although guaranteed, are not 100% tested in production.
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
5
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Electrical Characteristics (Continued)
The FLS0116 is a basic PWM controller for buck
converter topology in Continuous Conduction Mode
(CCM) with an intelligent PFC function that uses a
digital control algorithm. An internal self-biasing circuit
uses the high-voltage switching device. The IC does not
need an auxiliary powering path to the VCC pin typical
in flyback control ICs or PSR product family.
power for the IC, has voltage ripple as well as the
rectification voltage after bridge, changing voltage level
according to the VCC capacitor value. Using this kind of
voltage fluctuation on the VCC pin, the IC can detect
the time reference and create the internal ZCD signal.
For precise and reliable internal reference for input
voltage signal, the FLS0116 uses a digital technique
(sigma/delta modulation) and creates a new internal
signal (DAC_OUT) that has the same phase as the
input voltage, as shown in Figure 5. This signal enters
the final comparator and is compared with current
information from the sensing resistor.
When the input voltage applied to the HV pin is within
operating range (25 V to 500 V), the FLS0116
maintains a 15.5 V DC voltage at the VCC pin for stable
operation. The UVLO block functions such that when
the VCC voltage rises higher than VCCST+, the internal
UVLO block releases and starts operation. Otherwise,
the VCC goes down to the VCCST- and IC operation stops.
Normally, the hysteresis function provides stable
operation even if the input voltage is operating under
very noisy or unstable circumstances.
Vbridge
Bridge Diode
Output Voltage
JFET Output
Voltage
Input Voltage
Peak
The FLS0116 has a “smart” internal digital block for
determining input condition: AC or DC. When an AC
source with 50 Hz or 60 Hz is applied to the IC, the IC
automatically changes its internal reference signal,
which is similar to input signal, for creating high power
factor. When a DC source connects to the IC, the
internal reference immediately changes to DC.
t
VDD Charging Voltage
VCC
JFET Output Voltage
t
ZCD
t
DAC_OUT
t
Soft-Start Function
Figure 5. Internal PFC Function
The FLS0116 has an internal soft-start function to
reduce inrush current at startup. When the IC starts
operation following an internal sequence, the internal
reference slowly increases for a pre-determined fixed
time. After this transient period, the internal reference
goes to a steady-state level. In this time, the IC
continually tries to find phase information from the VCC
pin. If the IC succeeds in getting phase information, it
automatically follows a similar shape reference made
during the transient times, 7 periods. If not, the IC has a
DC reference level.
Self-Biasing Function
The self-biasing function, using an HV device, can
supply enough operating current to the IC and
guarantee similar startup time across the whole input
voltage range (80 V~308 VAC). However, self-biasing
has a weakness in high-voltage condition. Normally,
the HV device acts as constant current source, so the
internal HV device has power loss when high input
voltage connects to the HV pin. This power loss is
proportional to input voltage. To reduce this power
loss, one of the possible solutions is an additional
resistor between the input voltage source and the HV
pin, as shown in Figure 6.
Vbridge
ILED
L1
LED
D1
T/2 = 1/(Input Frequency * 2)
7*(T/2)
CS
Figure 4. Soft-Start Function in AC Input Mode
DRAIN
BD
C1
VCC
C2
HV
R3
GND
RT
Internal PFC Function: How to Achieve
High Power Factor
R1
ADIM
C3
R2
C4
L2
The FLS0116 has a simple, “smart”, internal PFC
function that does not require additional pins for
detecting input phase information or an electrolytic
capacitor for supply voltage stabilization. For achieving
high PF, the FLS0116 does not use the rectification
capacitor after the bridge diode. This is important
because the IC instead uses fluctuation in the signal on
the VCC pin. Basically, the VCC pin, which is supplies
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
L3
FLS0116
Fuse
Normal Operation
Figure 6. High-Voltage Application
www.fairchildsemi.com
6
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Functional Description
The FLS0116 uses the ADIM pin for analog or 0 V to
10 V dimming by using a resistive divider. The peak
voltage of internal reference, which is DAC_OUT signal
in Figure 5, is changed by the VADIM level, as shown in
Figure 7, and has different peak level according to the
operating mode.
Lm
n V f (1 Dmin )
f s i rip
VDAC _ OUT
AC Mode
I LED ( rms)
0. 5 V
3 . 5V
irip
(3)
[A]
2
In FL7701, the LED RMS current determines the
inductance parameter. To drive for CCM Mode, define
LED RMS current first, as:
DC Mode
0.365V
(2)
If the peak current is fixed at 350 mApk, the
formula for the peak current is:
I LED ( ave. peak) icon
0 .5 V
[H ]
I LED ( ave. peak) [A]
2
(4)
Substituting Equation (2) for Equation
inductance of inductor is obtained.
VADIM
(4),
the
Figure 7. VADIM vs. VDAC_OUT(peak)
VIN
Inductor Design
Π
The fixed internal duty ratio range is below 50%, or
around 400 ns, from a timing point of view. The range is
dependent on the input voltage and number of LEDs in
its string.
Dmin
4Π
t
Bridge Diode
Output Voltage
Vbridge
Input Voltage
Peak
Minimum duty is calculated as:
3Π
2Π
VDD Charging
Voltage
t
ZCD
t
n V f
DAC
(1)
Vin (max)
t
VLED
where:
η
= efficiency of system;
VIN(max)= maximum input voltage;
Vf
= forward drop voltage of LED; and
n
= LED number in series connection.
Vdrain
t
Input Voltage
Peak
t
ILED
Input Voltage
Peak
Current Limit
t
Average
LED Current
∆irip
IFRD
t
IMOSFET
ton toff
Dmin 1-Dmin
t
(a) DCM Mode
Iinput
Current peak at LED current
maximum point (ILED(peak))
Current peak at LED average
current maximum point
(ILED(ave.peak))
DCM
Average
LED Current (ILED(ave))
∆i
0.5∆i
t
T/2 = 1/(Input Frequency * 2)
DCM
T = 1/Input Ferquency
0.5∆i
Figure 9. Typical Performance Characteristics
CCM
Current min at LED current
maximum point (ILED(min))
Dmin
1-Dmin
ton toff
(b) CCM Mode
Figure 8. DCM and CCM Operation
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
7
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
In DCM Mode, inductance is:
Dimming Function
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Example Application Circuits
L1
LED
D1
L3
FLS0116
Fuse
CS
DRAIN
BD
C1
HV
VCC
C2
GND
RT
R1
ADIM
C3
C4
R2
L2
Figure 10. Application Circuit without Electrolytic Capacitor
L1
LED
ZD
C5
D1
L3
FLS0116
Fuse
CS
DRAIN
BD
C1
VCC
C2
HV
GND
RT
ADIM
R1 C3
C4
R2
L2
Figure 11. Application Circuit with Electrolytic Capacitor
L1
FLS0116
CS
Fuse
VCC
DRAIN
HV
R1
GND
BD
C1
C2
RT
L3
ADIM
C4
R2
C3
LED
D1
C5
ZD
L2
Figure 12. Application Circuit of High-Side Operation with Electrolytic Capacitor
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
8
17.0
6.0
16.5
5.5
VCCHV [V]
VCC[V]
16.0
15.5
5.0
15.0
4.5
14.5
14.0
-40
-20
0
20
40
60
80
100
4.0
-40
120
-20
0
Temperature [°C]
Figure 13.
20
40
60
80
100
120
Temperature [°C]
VCC vs. Temperature
Figure 14.
14.0
VCCHYS vs. Temperature
150
140
130
IST[A]
VCCST+[V]
13.5
13.0
120
110
12.5
100
12.0
-40
-20
0
20
40
60
80
100
90
-40
120
-20
0
Temperature [°C]
Figure 15.
20
40
60
80
100
120
100
120
Temperature [°C]
VCCST+ vs. Temperature
Figure 16.
9.0
IST vs. Temperature
48
47
fOSC [kHz]
VCCST-[V]
8.5
8.0
46
45
7.5
44
7.0
-40
-20
0
20
40
60
80
100
43
-40
120
-20
Temperature [°C]
Figure 17.
20
40
60
80
Temperature [°C]
VCCST- vs. Temperature
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
0
Figure 18.
fOSC vs. Temperature (RT=Open)
www.fairchildsemi.com
9
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Typical Characteristics
1.7
22
1.6
VRT[V]
fOSC [kHz]
24
20
18
1.5
1.4
16
-40
-20
0
20
40
60
80
100
1.3
-40
120
-20
0
Temperature [°C]
Figure 19.
Figure 20.
fOSC vs. Temperature (RT=87kΩ)
60
80
100
120
VRT vs. Temperature
0.375
280
0.370
260
VCS1 [V]
fOSC [kHz]
40
Temperature [°C]
300
0.365
240
0.360
220
0.355
200
-40
-20
0
20
40
60
80
100
0.350
-40
120
-20
0
Temperature [°C]
Figure 21.
20
40
60
80
100
120
Temperature [°C]
Figure 22.
fOSC vs. Temperature (RT=5.95kΩ)
52
19.5
51
19.0
OVPVCC [V]
DMAX [%]
20
50
49
VCS vs. Temperature
18.5
18.0
48
-40
-20
0
20
40
60
80
100
17.5
-40
120
-20
Temperature [°C]
Figure 23.
20
40
60
80
100
120
Temperature [°C]
DMAX vs. Temperature
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
0
Figure 24.
OVPVCC vs. Temperature
www.fairchildsemi.com
10
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Typical Characteristics
15
640
14
620
BVDSS [V]
IAD[A]
13
12
11
600
580
10
560
9
-40
-20
0
20
40
60
80
100
120
-40
-20
0
Temperature [°C]
Figure 25.
20
40
60
80
100
120
Temperature [°C]
IAD vs. Temperature
Figure 26.
BVDSS vs. Temperature
0.5
IDSS [A]
0.4
0.3
0.2
0.1
0.0
-40
-20
0
20
40
60
80
100
120
Temperature [°C]
Figure 27.
IDSS vs. Temperature
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
11
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Typical Characteristics
5.00
4.80
A
3.81
0.65TYP
3.81
7 6
5
B
1.75TYP
6.20
5.80
PIN #1
4.00
3.80
4
2 3
1
3.85 7.35
1.27
0.25
C B A
1.27
(0.33)
TOP VIEW
LAND PATTERN RECOMMENDATION
SEE DETAIL A
0.25
0.10
0.25
0.19
C
1.75 MAX
OPTION A - BEVEL EDGE
0.51
0.33
FRONT VIEW
0.10 C
OPTION B - NO BEVEL EDGE
0.50 x 45°
0.25
R0.10
NOTES:
GAGE PLANE
R0.10
0.36
A) THIS PACKAGE DOES NOT FULLY CONFORMS
TO JEDEC MS-012 VARIATION AA.
B) ALL DIMENSIONS ARE IN MILLIMETERS.
8°
0°
0.90
0.406
SEATING PLANE
(1.04)
C) DIMENSIONS DO NOT INCLUDE MOLD
FLASH OR BURRS.
D) DRAWING FILENAME : M07Brev3
DETAIL A
SCALE: 2:1
Figure 28.
7-Lead, Small-Outline Integrated Circuit (SOIC), JEDEC MS-012, .150-Inch Narrow Body
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify
or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically
the warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
12
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
Physical Dimensions
FLS0116 — MOSFET Integrated Smart LED Lamp Driver IC with PFC Function
© 2012 Fairchild Semiconductor Corporation
FLS0116 • Rev. 1.0.2
www.fairchildsemi.com
13
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com
工商网监
湘ICP备2023018690号
