Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FOD8320
High Noise Immunity, 2.5A Output Current, Gate Drive
Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Features
■ Fairchild’s
■
■
■
■
■
■
■
Description
Optoplanar®
Packaging Technology
Provides Reliable and High-Voltage Insulation with
Greater than 10 mm Creepage and Clearance
Distance, and 0.5 mm Internal Insulation Distance
While Still Offering a Compact Footprint
2.5 A Output Current Driving Capability for MediumPower IGBT/MOSFET
– P-Channel MOSFETs at Output Stage Enables
Output Voltage Swing Close to Supply Rail
35 kV/µs Minimum Common Mode Rejection
Wide Supply Voltage Range: 15 V to 30 V
Fast Switching Speed Over Full Operating
Temperature Range:
– 400 ns Maximum Propagation Delay
– 100 ns Maximum Pulse Width Distortion
Under-Voltage Lockout (UVLO) with Hysteresis
Extended Industrial Temperate Range: -40°C to 100°C
Safety and Regulatory Approvals:
– UL1577, 5,000 VRMS for 1 Minute
– DIN EN/IEC60747-5-5, 1,414 V Peak Working
Insulation Voltage
The FOD8320 is a 2.5 A output current gate drive
optocoupler, capable of driving medium-power IGBT/
MOSFETs. It is ideally suited for fast-switching driving of
power IGBT and MOSFET used in motor-control inverter
applications and high-performance power systems.
The FOD8320 utilizes Fairchild’s Optoplanar® coplanar
packaging technology and optimized IC design to
achieve reliable high-insulation voltage and high-noise
immunity.
It consists of an Aluminum Gallium Arsenide (AlGaAs)
Light-Emitting Diode (LED) optically coupled to an
integrated circuit with a high-speed driver for push-pull
MOSFET output stage. The device is housed in a wide
body, 5-pin, small-outline, plastic package.
Functional Schematic
6 VDD
ANODE 1
5 VO
Applications
■ AC and Brushless DC Motor Drives
CATHODE 3
4 VSS
■ Industrial Inverter
■ Uninterruptible Power Supply
■ Induction Heating
Figure 1. Schematic
■ Isolated IGBT/Power MOSFET Gate Drive
Related Resources
■ FOD3120, High Noise Immunity, 2.5 A Output
Current, Gate Drive Optocoupler Datasheet
■ www.fairchildsemi.com/products/opto/
Figure 2. Package Outline
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
September 2014
VDD – VSS “Positive Going”
(Turn-on)
LED
VDD – VSS “Positive Going”
(Turn-off)
VO
Off
0 V to 30 V
0 V to 30 V
LOW
On
0 V to 11.5 V
0 V to 10 V
LOW
On
11.5 V to 14.5 V
10 V to 13 V
Transition
On
14.5 V to 30 V
13 V to 30 V
HIGH
Pin Configuration
1
6
ANODE
CATHODE
5
3
4
VDD
VO
VSS
Figure 3. Pin Configuration
Pin Definitions
Pin #
Name
Description
1
Anode
3
Cathode
4
VSS
Negative Supply Voltage
5
VO
Output Voltage
6
VDD
Positive Supply Voltage
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
LED Anode
LED Cathode
www.fairchildsemi.com
2
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Truth Table
As per DIN EN/IEC60747-5-5, this optocoupler is suitable for “safe electrical insulation” only within the safety limit
data. Compliance with the safety ratings shall be ensured by means of protective circuits.
Symbol
Parameter
Min.
Typ.
Max.
Unit
Installation Classifications per DIN VDE 0110/1.89 Table 1
For Rated Mains Voltage < 150 VRMS
I–IV
For Rated Mains Voltage < 300 VRMS
I–IV
For Rated Mains Voltage < 450 VRMS
I–IIII
For Rated Mains Voltage < 600 VRMS
I–III
Climatic Classification
40/100/21
Pollution Degree (DIN VDE 0110/1.89)
CTI
VPR
2
Comparative Tracking Index
175
Input-to-Output Test Voltage, Method b, VIORM x 1.875 = VPR,
100% Production Test with tm = 1 s, Partial Discharge < 5 pC
2651
Vpeak
Input-to-Output Test Voltage, Method a, VIORM x 1.6 = VPR,
Type and Sample Test with tm = 10 s, Partial Discharge < 5 pC
2262
Vpeak
VIORM
Maximum Working Insulation Voltage
1414
Vpeak
VIOTM
Highest Allowable Over Voltage
8000
Vpeak
External Creepage
10.0
mm
External Clearance
10.0
mm
Insulation Thickness
0.5
mm
150
°C
Safety Limit Values – Maximum Values Allowed in the
Event of a Failure
TS
Case Temperature
IS,INPUT
Input Current
200
mA
PS,OUTPUT
Output Power
600
mW
109
Ω
RIO
Insulation Resistance at TS, VIO = 500 V
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
3
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Safety and Insulation Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only. TA = 25ºC unless otherwise specified.
Symbol
Parameter
Value
Units
TSTG
Storage Temperature
-40 to +125
°C
TOPR
Operating Temperature
-40 to +100
°C
Junction Temperature
-40 to +125
°C
260 for 10 s
°C
TJ
Lead Solder Temperature
TSOL
Refer to Reflow Temperature Profile on page 15.
IF(AVG)
Average Input Current
25
mA
F
Operating Frequency
50
kHz
VR
Reverse Input Voltage
5.0
V
3.0
A
IO(PEAK)
VDD
VO(PEAK)
tR(IN), tF(IN)
Peak Output
Current(1)
Supply Voltage
Peak Output Voltage
Input Signal Rise and Fall Time
Dissipation(2)(4)
PDI
Input Power
PDO
Output Power Dissipation(3)(4)
0 to 35
V
0 to VDD
V
500
ns
45
mW
500
mW
Notes:
1. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%.
2. No derating required across operating temperature range.
3. Derate linearly from 25°C at a rate of 5.2 mW/°C.
4. Functional operation under these conditions is not implied. Permanent damage may occur if the device is subjected
to conditions outside these ratings.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to absolute maximum ratings.
Symbol
Min.
Max.
Unit
Ambient Operating Temperature
-40
100
°C
Supply Voltage
16
30
V
IF(ON)
Input Current (ON)
7
16
mA
VF(OFF)
Input Voltage (OFF)
0
0.8
V
TA
VDD – VSS
Parameter
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
4
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Absolute Maximum Ratings
Apply over all recommended conditions, typical value is measured at TA = 25ºC.
Symbol
Parameter
Conditions
Min.
VISO
Input-Output Isolation
Voltage
TA = 25ºC, R.H. < 50%, t = 60 s,
II-O ≤ 20 µA, 50 Hz(5)(6)
RISO
Isolation Resistance
VI-O = 500 V(5)
CISO
Isolation Capacitance
VI-O = 0 V, Frequency = 1.0
Typ.
Max.
5,000
MHz(6)
Units
VRMS
1011
Ω
1
pF
Notes:
5. Device is considered a two terminal device: pins 1 and 3 are shorted together and pins 4, 5 and 6 are shorted
together.
6. 5,000 VACRMS for 1 minute duration is equivalent to 6,000 VACRMS for 1 second duration.
Electrical Characteristics
Apply over all recommended conditions, typical value is measured at VDD = 30 V, VSS = Ground, TA = 25°C unless
otherwise specified.
Symbol
VF
Δ(VF / TA)
Parameter
Conditions
Input Forward Voltage
Min.
Typ.
Max.
Units
Figure
1.1
1.5
1.8
V
19
Temperature Coefficient of IF = 10 mA
Forward Voltage
-1.8
BVR
Input Reverse Breakdown
Voltage
IR = 10 µA
CIN
Input Capacitance
f = 1 MHz, VF = 0 V
IOH
High Level Output
Current(1)
VOH = VDD – 3 V
1.0
VOH = VDD – 6 V
2.0
IOL
Low Level Output
Current(1)
VOL = VSS + 3 V
1.0
VOL = VSS + 6 V
2.0
VOH
High Level Output
Voltage(7)(8)
VOL
Low Level Output
Voltage(7)(8)
IDDH
mV/°C
5
V
60
2.0
2.0
IF = 10 mA, IO = -2.5 A
VDD – 6.25
VDD – 2.5
IF = 10 mA, IO = -100 mA
VDD – 0.5
VDD – 0.1
pF
2.5
A
4, 6
2.5
A
4, 6, 22
2.5
A
7, 9
2.5
A
7, 9, 21
V
4
4, 5, 23
IF = 10 mA, IO = 2.5 A
VSS + 2.5
VSS + 6.25
IF = 0 mA, IO = 100 mA
VSS + 0.1
VSS + 0.5
High Level Supply Current VO Open, IF = 7 to 16 mA
2.9
3.8
mA
10, 11,
25
IDDL
Low Level Supply Current
VO Open, VF = 0 to 0.8 V
2.8
3.8
mA
10, 11,
26
IFLH
Threshold Input Current
Low to High
IO = 0 mA, VO > 5 V
2.4
5.0
mA
12, 18,
27
VFHL
Threshold Input Voltage
High to Low
IO = 0 mA, VO < 5 V
0.8
V
28
UnderVoltage Lockout
Threshold
IF = 10 mA, VO > 5 V
11.5
12.7
14.5
V
20, 29
VUVLO-
IF = 10 mA, VO < 5 V
10.0
11.2
13.0
V
20, 29
UVLOHYS
UnderVoltage Lockout
Threshold Hysteresis
VUVLO+
1.5
V
7
8, 24
V
Notes:
7. In this test, VOH is measured with a dc load current of 100 mA. When driving capacitive load VOH will approach VDD
as IOH approaches 0 A.
8. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
5
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Isolation Characteristics
Apply over all recommended conditions, typical value is measured at VDD = 30V, VSS = Ground, TA = 25°C unless
otherwise specified.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Units
Figure
tPHL
Propagation Delay Time to
Logic Low Output(9)
150
285
400
ns
13, 14,
15, 16,
17, 30
tPLH
Propagation Delay Time to
Logic High Output(10)
150
260
400
ns
13, 14,
15, 16,
17, 30
PWD
Pulse Width Distortion(11)
| tPHL – tPLH |
25
100
ns
PDD
(Skew)
Propagation Delay Difference
Between Any Two Parts(12)
IF = 7 mA to 16 mA, Rg = 10 Ω,
Cg = 10 nF, f = 10 kHz,
Duty Cycle = 50%
-250
250
tR
Output Rise Time
(10% to 90%)
60
ns
30
tF
Output Fall Time
(90% to 10%)
60
ns
30
tULVO ON
ULVO Turn On Delay
IF = 10 mA, VO > 5 V
0.8
µs
tULVO OFF
ULVO Turn Off Delay
IF = 10 mA, VO < 5 V
0.4
µs
| CMH |
Common Mode Transient
Immunity at Output High
TA = 25°C, VDD = 30 V,
IF = 7 mA to 16 mA,
VCM = 2000 V(13)
35
50
kV/µs
31
| CML |
Common Mode Transient
Immunity at Output Low
TA = 25°C, VDD = 30 V, VF = 0 V,
VCM = 2000 V(14)
35
50
kV/µs
31
Notes:
9. Propagation delay tPHL is measured from the 50% level on the falling edge of the input pulse to the 50% level of the
falling edge of the VO signal.
10. Propagation delay tPLH is measured from the 50% level on the rising edge of the input pulse to the 50% level of the
rising edge of the VO signal.
11. PWD is defined as | tPHL – tPLH | for any given device.
12. The difference between tPHL and tPLH between any two FOD8320 parts under the same operating conditions, with
equal loads.
13. Common mode transient immunity at output high is the maximum tolerable negative dVcm/dt on the trailing edge of
the common mode impulse signal, VCM, to ensure that the output remains high (i.e., VO > 15.0 V).
14. Common mode transient immunity at output low is the maximum tolerable positive dVcm/dt on the leading edge of
the common pulse signal, VCM, to ensure that the output remains low (i.e., VO < 1.0 V).
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
6
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Switching Characteristics
VOH–VDD – OUTPUT HIGH VOLTAGE DROP (V)
VOH – V DD – OUTPUT HIGH VOLTAGE DROP (V)
0
-0.5
-1.0
-1.5
TA = -40°C
-2.0
25°C
-2.5
100°C
-3.0
VDD = 15 V to 30 V
VSS = 0 V
IF = 7 mA to 16 mA
f = 200 Hz 0.2% Duty Cycle
-3.5
-4.0
0
0.5
1.0
1.5
2.0
2.5
0
-0.05
-0.10
-0.15
-0.20
VDD = 15 V to 30 V
VSS = 0 V
IF = 7 mA to 16 mA
IO = -100 mA
-0.25
-0.30
-40
-20
0
Figure 4. Output High Voltage Drop
vs. Output High Current
VOL – OUTPUT LOW VOLTAGE (V)
IOH – OUTPUT HIGH CURRENT (A)
6
5
VO = V DD – 6 V
4
VO = V DD – 3 V
3
2
VDD = 15 V to 30 V
VSS = 0 V
IF = 7 mA to 16 mA
f = 200 Hz 0.2% Duty Cycle
-20
0
TA = 100°C
25°C
2
-40°C
1
0
20
40
60
80
100
0
0.5
1.0
1.5
2.0
2.5
IOL – OUTPUT LOW CURRENT (A)
Figure 7. Output Low Voltage
vs. Output Low Current
0.25
8
VDD = 15 V to 30 V
VSS = 0 V
VF = 0 V or 0.8 V
IO = 100 mA
IOL – OUTPUT LOW CURRENT (A)
VOL – OUTPUT LOW VOLTAGE (V)
100
3
Figure 6. Output High Current
vs. Ambient Temperature
0.15
0.10
0.05
0
-40
80
VDD = 15 V to 30 V
VSS = 0 V
IF = 0 mA
f = 200 Hz 99.8% Duty Cycle
TA – AMBIENT TEMPERATURE (°C)
0.20
60
4
7
0
-40
40
Figure 5. Output High Voltage Drop
vs. Ambient Temperature
8
1
20
TA – AMBIENT TEMPERATURE (°C)
IOH – OUTPUT HIGH CURRENT (A)
-20
0
20
40
60
80
VO = V SS + 6V
4
VO = VSS + 3V
2
0
-40
100
TA – AMBIENT TEMPERATURE (°C)
-20
0
20
40
60
80
100
TA – AMBIENT TEMPERATURE (°C)
Figure 8. Output Low Voltage
vs. Ambient Temperature
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
6
VDD = 15 V to 30 V
VSS = 0 V
IF = 0 A
f = 200 Hz 99.8% Duty Cycle
Figure 9. Output Low Current
vs. Ambient Temperature
www.fairchildsemi.com
7
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Typical Performance Characteristics
3.6
VDD = 30 V
VSS = 0 V
IF = 10 mA (for IDDH)
IF = 0 mA (for IDDL)
3.2
IDD – SUPPLY CURRENT (mA)
IDD – SUPPLY CURRENT (mA)
3.6
IDDH
2.8
IDDL
2.4
2.0
-40
-20
0
20
40
60
80
IF = 10 mA (for IDDH)
IF = 0 mA (for IDDL)
VSS = 0 V
TA = 25°C
3.2
IDDH
2.8
IDDL
2.4
2.0
15
100
20
TA – AMBIENT TEMPERATURE (°C)
Figure 10. Supply Current
vs. Ambient Temperature
3.5
tP – PROPAGATION DELAY (ns)
IFLH – LOW TO HIGH INPUT CURRENT
THRESHOLD (mA)
500
VDD = 15 V to 30 V
VSS = 0 V
Output = Open
3.0
2.5
2.0
1.5
1.0
-40
-20
0
20
40
60
80
IF = 10 mA
Rg = 10 Ω
Cg = 10 nF
TA = 25°C
f = 10 kHz 50% Duty Cycle
400
tPHL
300
tPLH
200
100
15
100
18
TA – AMBIENT TEMPERATURE (°C)
21
24
27
30
VDD – SUPPLY VOLTAGE (V)
Figure 13. Propagation Delay
vs. Supply Voltage
Figure 12. Low to High Input Current Threshold
vs. Ambient Temperature
500
500
VDD = 30 V
VSS = 0 V
f = 10 kHz 50% Duty Cycle
Rg = 10 Ω
400 Cg = 10 nF
TA = 25°C
tP – PROPAGATION DELAY (ns)
tP – PROPAGATION DELAY (ns)
30
Figure 11. Supply Current
vs. Supply Voltage
4
tPHL
300
tPLH
200
100
25
VDD – SUPPLY VOLTAGE (V)
6
8
10
12
14
tPHL
300
tPLH
200
100
-40
16
IF – FORWARD LED CURRENT (mA)
-20
0
20
40
60
80
100
TA – AMBIENT TEMPERATURE (°C)
Figure 15. Propagation Delay
vs. Ambient Temperature
Figure 14. Propagation Delay
vs. LED Forward Current
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
400
VDD = 30 V
VSS = 0 V
IF = 10 mA
f = 10 kHz 50% Duty Cycle
Rg = 10 Ω
Cg = 10 nF
www.fairchildsemi.com
8
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Typical Performance Characteristics (Continued)
500
VDD = 30 V
VSS = 0 V
IF = 10 mA
f = 10 kHz 50% Duty Cycle
400 Cg = 10 nF
TA = 25°C
VDD = 30 V
VSS = 0 V
IF = 10 mA
f = 10 kHz 50% Duty Cycle
400 Rg = 10 Ω
TA = 25°C
tP – PROPAGATION DELAY (ns)
tP – PROPAGATION DELAY (ns)
500
tPHL
300
tPLH
200
100
0
10
20
30
40
tPLH
200
100
50
tPHL
300
0
20
Rg – SERIES LOAD RESISTANCE (Ω)
Figure 16. Propagation Delay
vs. Series Load Resistance
80
100
100
VDD = 30 V
TA = 25°C
IF – FORWARD CURRENT (mA)
30
VO – OUTPUT VOLTAGE (V)
60
Figure 17. Propagation Delay
vs. Load Capacitance
35
25
20
15
10
5
0
40
Cg – LOAD CAPACITANCE (nF)
0
1
2
3
4
10
100°C
1
0.1
0.01
0.001
0.6
5
-40°C
25°C
0.8
I F – FORWARD LED CURRENT (mA)
1.0
1.2
1.4
1.6
1.8
VF – FORWARD VOLTAGE (V)
Figure 18. Transfer Characteristics
Figure 19. Input Forward Current
vs. Forward Voltage
14
IF = 10 mA
TA = 25°C
VO – OUTPUT VOLTAGE (V)
12
10
8
VUVLO = 11.56 V
VUVLO = 13.12 V
6
4
2
0
0
5
10
15
20
VDD–VSS – SUPPLY VOLTAGE (V)
Figure 20. Under Voltage Lockout
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
9
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Typical Performance Characteristics (Continued)
Power Supply
+
+
C1
0.1 μF
Pulse Generator
PW = 4.99 ms
Period = 5 ms
ROUT = 50 Ω
VDD = 15 V to 30 V
C2
47 μF
Pulse-In
1
6
IOL
R2
100 Ω
Power Supply
+
5
D1
VOL
3
+
C3
0.1 μF
V=6V
C4
47 μF
4
LED-IFmon
To Scope
R1
100 Ω
Test Conditions:
Frequency = 200 Hz
Duty Cycle = 99.8%
VDD = 15 V to 30 V
VSS = 0 V
IF = 0 mA
Figure 21. IOL Test Circuit
Power Supply
+
+
C1
0.1 μF
VDD = 15 V to 30 V
C2
47 μF
Pulse Generator
PW = 10 μs
Period = 5 ms
ROUT = 50 Ω
Pulse-In
1
+
6
IOH
R2
100 Ω
3
4
C4
47 μF
Power Supply
V=6V
–
5
D1
VOH
LED-IFmon
+
C3
0.1 μF
Current
Probe
To Scope
R1
100 Ω
Test Conditions:
Frequency = 200 Hz
Duty Cycle = 0.2%
VDD = 15 V to 30 V
VSS = 0 V
IF = 7 mA to 16 mA
Figure 22. IOH Test Circuit
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
10
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Test Circuit
1
6
0.1 μF
+
–
VO
5
IF = 7 mA to 16 mA
VDD = 15 V to 30 V
100 mA
3
4
Figure 23. VOH Test Circuit
1
6
0.1 μF
5
3
100 mA
VO
+
–
VDD = 15 V to 30 V
4
Figure 24. VOL Test Circuit
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
11
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Test Circuit (Continued)
6
1
0.1 μF
IF = 7 mA to 16 mA
VO
5
3
+
–
VDD = 30 V
+
–
VDD = 30 V
4
Figure 25. IDDH Test Circuit
6
1
0.1 μF
+
–
5
VF = -3.0 V to 0.8 V
VO
4
3
Figure 26. IDDL Test Circuit
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
12
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Test Circuit (Continued)
6
1
0.1 μF
VO > 5 V
5
+
–
VDD = 15 V to 30 V
+
–
VDD = 15 V to 30 V
IF
3
4
Figure 27. IFLH Test Circuit
1
6
0.1 μF
+
–
VO
5
VF = –3.0 V to 0.8 V
3
4
Figure 28. VFHL Test Circuit
1
6
0.1 μF
IF = 10 mA
5
3
VO = 5 V
+
–
15 V or 30 V
VDD Ramp
4
Figure 29. UVLO Test Circuit
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
13
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Test Circuit (Continued)
6
1
0.1 μF
5
VO
+
–
Rg = 10 Ω
Probe
f = 10 kHz
DC = 50%
3
4
+
–
VDD = 15 V to 30 V
+
–
VDD = 30 V
Cg = 10 nF
50 Ω
IF
tR
tF
90%
50%
VOUT
10%
tPLH
tPHL
Figure 30. tPHL, tPLH, tR and tF Test Circuit and Waveforms
IF
A
6
1
B
5V
0.1 μF
+
–
5
3
VO
4
+–
VCM = 2,000 V
VCM
0V
Δt
VO
VOH
Switch at A: IF = 10 mA
VO
VOL
Switch at B: IF = 0 mA
Figure 31. CMR Test Circuit and Waveforms
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
14
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Test Circuit (Continued)
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Reflow Profile
Temperature (°C)
TP
260
240
TL
220
200
180
160
140
120
100
80
60
40
20
0
Maximum Ramp-up Rate = 3°C/s
Maximum Ramp-down Rate = 6°C/s
tP
Tsmax
tL
Preheat Area
Tsmin
ts
120
240
360
Time 25°C to Peak
Time (seconds)
Profile Freature
Pb-Free Assembly Profile
Temperature Minimum (Tsmin)
150°C
Temperature Maximum (Tsmax)
200°C
Time (tS) from (Tsmin to Tsmax)
60 s to 120 s
Ramp-up Rate (tL to tP)
3°C/second maximum
Liquidous Temperature (TL)
217°C
Time (tL) Maintained Above (TL)
60 s to 150 s
Peak Body Package Temperature
260°C +0°C / –5°C
Time (tP) within 5°C of 260°C
30 s
Ramp-Down Rate (TP to TL)
6°C/s maximum
Time 25°C to Peak Temperature
8 minutes maximum
Figure 32. Reflow Profile
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
15
Part Number
Package
Packing Method
FOD8320
Wide Body SOP 5-Pin
Tube (100 units per tube)
FOD8320R2
Wide Body SOP 5-Pin
Tape and Reel (1,000 units per reel)
FOD8320V
Wide Body SOP 5-Pin, DIN EN/IEC60747-5-5 Option Tube (100 units per tube)
FOD8320R2V
Wide Body SOP 5-Pin, DIN EN/ IEC60747-5-5 Option Tape and Reel (1,000 units per reel)
All packages are lead free per JEDEC: J-STD-020B standard.
Marking Information
1
2
3
8320 V
D X YY KK W
4
6
5
8
7
Definitions
1
Fairchild logo
2
Device number, e.g., ‘8320’ for FOD8320
3
DIN EN/IEC60747-5-5 Option (only appears on
component ordered with this option)
4
Plant code, e.g., ‘D’
5
Last digit year code, e.g., ‘C’ for 2012
6
Two digit work week ranging from ‘01’ to ‘53’
7
Lot traceability code
8
Package assembly code, W
©2010 Fairchild Semiconductor Corporation
FOD8320 Rev. 1.0.7
www.fairchildsemi.com
16
FOD8320 — High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler in Optoplanar® Wide Body SOP 5-Pin
Ordering Information
0.20 C A-B
3.95
0.60
2X
1.27
4
6
D
1.38
A
6
4
1.27
4.60
11.38
11.80
11.60
9.20
0.10 C D
2X
1
3
1
0.33 C
PIN ONE
INDICATOR
B
2.54
0.25
5X 0.51
0.31
2.54
C A-B D
LAND PATTERN
RECOMMENDATION
5 TIPS
A
2.65
2.45
0.10 C
3
SEATING
PLANE
2.95 MAX
0.10 C
0.30
0.10
5X
C
NOTES: UNLESS OTHERWISE SPECIFIED
1.35
1.15
GAUGE
PLANE
8°
0°
0.25
C
(R1.29)
SEATING
PLANE
SCALE: 3.2:1
0.74
0.44
A) THIS PACKAGE DOES NOT
CONFORM TO ANY STANDARD.
B) ALL DIMENSIONS ARE IN
(R0.54)
MILLIMETERS.
C) DIMENSIONS ARE EXCLUSIVE OF
BURRS, MOLD FLASH AND TIE BAR
PROTRUSIONS
D) DRAWING CONFORMS TO ASME
0.25
Y14.5M-1994
0.19
E) DRAWING FILE NAME:
MKT-M05AREV3
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com
工商网监
湘ICP备2023018690号
