FPF2026

Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FPF2024/25/26/27 Full Functional Load Switch with 100 mA Current Limit Features Description   1.6 V to 5.5 V Input Voltage Range          Typical RDS(ON) = 225 mΩ at VIN = 3.3 V The FPF2024/5/6/7 are low RDS(ON) P-Channel MOSFET load switches with 150 mA typical current limit value targeting small package load switch applications. The extended input voltage range spans from 1.6 V to 5.5 V to fulfill today's ultra-portable device's supply requirements. Switch control is by a logic input (ON) capable of interfacing directly with a low voltage control signal. Ultra Low Average Quiescent Current 1 μA Typical at1.8 V Typical RDS(ON) = 280 mΩ at VIN = 1.8 V 100 mA Fixed Current Limit Minimum Under-Voltage Lockout (UVLO) CMOS and Open Drain Fault Flag Options Fault Blanking Auto Restart Thermal Shutdown ESD Protection o o >5500 V HBM >1500 V CDM Applications       PDAs Cell Phones GPS Devices Digital Cameras The FPF2024/25/26/27 respond to an output overload condition by going into constant current mode where the output current is regulated by the load switch. If the over-current condition persists beyond the 10 ms Blanking Time, the FPF2024 and FPF2025 pull the fault signal pin (FLAGB) low and shut-off the switch. An AutoRestart feature turns the FPF2024 and FPF2025 on again after 70 ms if the ON pin is still active. The FPF2026 has a Latch-Off feature which shuts off the switch off after the expiration of the 10 ms Blanking Time and keeps it off until the ON pin is toggled. The FPF2027 responds to an overload condition by immediately pulling the fault signal pin LOW and the switch remains in constant current mode until the output overload condition is removed. The FPF2027 has a Startup Blanking feature which prevents startup transient over-current conditions from triggering the fault signal pin for 10 ms after initial turn on via the ON pin. These parts are available in a space-saving 6-ball 2 advanced. Pb-Free 1.0 x1.5 mm CSP package. Peripheral Ports MP3 Players Figure 1. © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 2 6-Ball 1.0 x1.5 mm CSP Package www.fairchildsemi.com FPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit April 2016 Blank Current Auto-Restart Limit Time Time [ms] [ms] Part Number Min. Limit [mA] ON Pin Activity FLAGB Top Mark FPF2024 100 10 70 Active HI Open Drain S2 FPF2025 100 10 70 Active LO CMOS S3 FPF2026 FPF2027 100 10 n/a Active HI Open Drain S4 100 0 n/a Active HI Open Drain S5 Typical Application Figure 2. Typical Application Block Diagram Figure 3. © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 Block Diagram www.fairchildsemi.com 2 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Ordering Information Figure 4. Pin Assignment 1.0 x 1.5 CSP Bottom View Pin Description Pin Name A1 VOUT A2 VIN B1 GND B2 NC C1 FLAGB C2 ON Function Switch Output. Output of the power switch. Supply Input. Input to the power switch and the supply voltage for the IC. Ground. No Connection. Fault Output. Active LOW, open drain output for PFPF2024/26/27 and CMOS output for FPF2025. FLAGB indicates an over-current, supply under-voltage or over-temperature state. ON/OFF Control Input. Active HIGH for FPF2024/26/27 and Active LOW for FPF2025. © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 3 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Pin Configuration Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol VIN Parameter VIN, VOUT, ON, FLAG, GND Min. Max. Unit -0.3 6.0 V (1) PD Power Dissipation at TA=25°C 1.2 W ISW Maximum Continuous Switch Current 0.2 A TA Operating Temperature Range -40 125 °C TSTG Storage Junction Temperature -65 150 °C JA Thermal Resistance, Junction-to-Ambient 85 °C/W ESD Electrostatic Discharge Capability Human Body Model 5500 Charged Device Model 1500 V Note: 1. Package power dissipation on 1 square inch pad, 2 oz. copper board. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Min. Max. Unit VIN Input Voltage 1.6 5.5 V TA Ambient Operating Temperature -40 85 °C © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 4 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Absolute Maximum Ratings Unless otherwise noted, VIN=1.6 to 5.5 V and TA=-40 to +85°C. Typical values are at VIN=3.3 V and TA=25°C. Symbol Parameter Conditions Min. Typ. Max. Unit 5.5 V 4 μA 1 μA Basic Operation VIN Operating Voltage 1.6 IQ Quiescent Current IOUT=0 mA, VON Active, VIN=1.8 V (Average) ISD Shutdown Current VON=VIN, (FPF2025) VON=GND (FPF2024/26/27), IOUT=0 1 TA=25°C, VIN=5.5 V TA=-40 to 85°C, VIN=5.5 V RON On Resistance 120 TA=25°C,VIN=3.3 V TA= -40 to +85°C, VIN=3.3 V 140 TA= 25°C,VIN=1.6 V VIH On Input Logic HIGH Voltage VIL On Input Logic LOW Voltage ION ISWOFF TA= -40 to +85°C, VIN=1.6 V 180 VIN=1.6 V 0.8 VIN=5.5 V 1.5 215 315 215 350 225 325 225 360 305 490 305 580 mΩ V VIN=1.6 V 0.45 VIN=5.5 V 0.9 On Input Leakage VON=VIN or GND 1.0 μA Off Switch Leakage VON=VIN, VOUT=0 V 1.0 μA FLAGB Output Logic Low Voltage FLAGB Output Logic High Voltage VIN=5.5 V, ISINK=1 mA 0.1 0.2 VIN=1.8 V, ISINK=1 mA 0.1 0.3 VIN=5.5 V, ISOURCE=1 mA, FPF2025 5.2 5.4 VIN=1.6 V, ISOURCE=1 mA, FPF2025 1.20 1.35 FLAGB Output High Leakage Current VIN=5.5 V, Switch On, FPF2024, FPF2026, FPF2027 Current Limit VIN=3.3 V, VOUT=3.0 V,TA=25°C V V V 1.0 μA 200 mA Protections ILIM Thermal Shutdown 100 140 Return from Shutdown 130 Hysteresis UVLO Under-Voltage Lockout UVLOH Under-Voltage Lockout Hysteresis 150 Shutdown Threshold TJ Increasing °C 10 VIN Increasing 1.475 1.525 1.575 V 40 mV Dynamic Characteristics tON Turn-On Time RL = 500 Ω, CL = 0.1 μF 70 μs μs tOFF Turn-Off Time RL = 500 Ω 10 tRISE VOUT Rise Time RL = 500 Ω, CL = 0.1 μF 30 tBLANK Over-Current Blanking Time FPF2024, FPF2025, FPF2026 TSTART_BLANK Startup FLAGB Blanking Time tRSTRT Auto-Restart Time 5 10 FPF2027(2) 5 FPF2024, FPF2025 35 128.5 Sleep Mode Duration Wake-up Mode Duration 0.5 μs 20 ms 10 20 ms 70 140 ms 257.0 514.0 ms 1.0 2.0 ms Duty Cycle Wake-up: Sleep Mode Duty Cycle 1:257 Current Limit Response Time Moderate Over-Current Condition RL= 5  15 Blanking/Auto-Restart Duty Ratio tBLANK /tRSTRT (Internally Fixed) FPF2024, FPF2025 1:7 μs Note: 2. FPF2027 has a 10 ms Startup FLAGB Blanking Time when the part is turned on via ON pin to ensure transient load currents settle down. © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 5 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Electrical Characteristics Figure 5. Shutdown Current vs. Temperature Figure 6. TRestart vs. Temperature Figure 7. Quiescent Current vs. Temperature Figure 8. TBlank vs. Temperature Figure 10. RDS(ON) vs. Temperature Figure 9. RDS(ON) vs. VIN © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 6 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Typical Performance Characteristics PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Typical Performance Characteristics (Continued) Figure 11. ILimit vs. VIN Figure 13. VIH, VIL vs. Temperature Figure 15. FPF2024 tOFF Response © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 Figure 12. Figure 14. Figure 16. ILimit vs. Temperature FPF2024 tON Response FPF2024 TBLANK Response (3) www.fairchildsemi.com 7 Figure 17. (3) FPF2024 TRESTART Response Figure 18. FPF2024 Current Limit Response Time (Output is loaded by 5 Ω and COUT = 10 μF) Figure 19. FPF2024 Current Limit Response Time (Output is loaded by 5 Ω and COUT = 100 μF) Figure 20. FPF2024 Short Circuit Response Time (Output shorted to GND while the switch is in normal operation) Figure 21. FPF2024 Current Limit Response (Input and enable pin are tied together and VOUT is shorted to GND) Figure 22. FPF2027 Over-Current Over-Current condition is applied while device in normal operation (FLAGB inserts immediately and reports the fault condition) © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 (3) www.fairchildsemi.com 8 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Typical Performance Characteristics (Continued) Figure 23. FPF2027 Startup FLAGB Blanking Time Figure 24. FPF2025 TBLANK and TRESTART (Active LO Device) Note: 3. VDRV signal forces the device to go into over-current condition by loading a 7.5 Ω. © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 9 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Typical Performance Characteristics (Continued) FPF2024-FPF2027 series Full-Function switches are current limited load switches with ultra-low power consumption. The core of each device consists of a 230 mW P-channel MOSFET featuring slow turn-on to limit the inrush current, fast turn-off, current limit, UnderVoltage Lockout (UVLO) and thermal shutdown protection features and a FLAGB output that indicates that a fault condition has occurred. the OFF state when the ON pin is inactive. In addition, FPF2026 moves into the OFF state if a current fault is encountered for longer duration than the Blanking Time. For all versions, an under-voltage on VIN or a junction temperature in excess of 140°C overrides the ON control and turns off the switch. In addition, a current fault condition longer than the Blanking Time will cause the switch to turn off in the FPF2024, FPF2025 and FPF2026. The FPF2024 and FPF2025 have an Auto-Restart feature which will automatically turn the switch on again after 70 ms. For the FPF2026, the ON pin must be toggled to turn the switch on again. The FPF2027 does not turn off in response to an over-current condition, and remains in a constant current mode for so long as the ON pin is active, and the thermal shutdown or UVLO are not activated. Some versions in the FPF202x series also feature Current Limit Blanking and Auto-Restart. The FPF202x family achieves an ultra-low current consumption of 1 μA through a proprietary “Sleep and Wake-up Modes” implementation. Full functionality is guaranteed for operating voltages down to 1.6 V over the -40°C to +85°C temperature range. Sleep and Wakeup Mode Description The ON pin control voltage and VIN pin have independent recommended operating ranges. The ON pin voltage can be driven by a voltage level higher than the input voltage. The ultra-low power consumption of FPF2024-FPF2027 is achieved through the implementation of proprietary Sleep/ Wakeup modes. The FPF2024-FPF2027 family turns on in Startup mode where it checks for potential load current, temperature, and under-voltage faults for 10 ms. If no faults are detected during this startup period, the FPF2024FPF2027 goes into a Sleep mode where it stays for 257 ms. At the end of the Sleep period, the part goes into Wakeup mode to check for any fault condition. If no fault is detected in 1 ms, the part goes back to Sleep mode. The 1:257 Wakeup/Sleep duty cycle results in an overall average current consumption of 1 μA (typical). Fault Reporting Over-current, input under-voltage, or over-temperature fault conditions are signaled out by the FLAGB pin going low. FPF2024, FPF2025 and FPF2026 have a current fault blanking feature which prevents current faults lasting shorter than the Blanking Time of 10 ms (typical) from triggering the fault signal (FLAGB) output. If the over-current condition persists beyond the Blanking Time, the FPF2024 and FPF2025 pull the FLAGB pin low and shut the switch off. If the ON pin is kept active, an Auto-Restart feature releases the FLAGB pin and turns the switch on again after 70 ms. During Sleep mode the thermal and under-voltage conditions are not monitored to reduce the current consumption of the device. The switch current limiting circuitry is active at all times and protects the FPF2024-FPF2027 against excessive load currents in all modes. While in the Wakeup mode, a current fault event will prevent the part from reentering into Sleep mode even if input voltage and temperature faults are not present. In such a case, the part functions according to its feature set, e.g., it performs its normal Blanking, Auto-Restart or Latch-off functions as expected. If the over-current condition is removed from the output, the part will go back into Sleep mode after 10ms. The representative state diagrams of the FPF2024-FPF2027 are given in Figure 25, Figure 26 and Figure 27. If the over-current condition persists beyond the Blanking Time, the FPF2026 has a Latch-Off feature which pulls the FLAGB pin low and shuts the switch off. The switch is kept off and the FLAGB pin is kept low until the ON pin is toggled. The FPF2027 responds to an overload condition by immediately pulling the FLAGB pin low and the switch remains in constant current mode until the output overload condition is removed. The FPF2027 has a Startup Blanking feature which prevents current faults related to startup transients from triggering the FLAGB output. The Startup Blanking feature is effective for the first 10 ms (typical) following device turn-on via ON pin. The ultra-low quiescent current consumption of 1 μA along with the very-low minimum operating voltage of 1.6 V, make the FPF2024-FPF2027 an ideal fullfunction load switch for ultraportable applications. The FPF2024, FPF2026 and FPF2027 have an opendrain MOSFET FLAGB output which requires a pull-up resistor between VIN and FLAGB. A 100 KΩ pull up resistor is recommended. The FPF2025 has a CMOS FLAGB output and does not require a pull-up resistor. During shutdown, the pull-down on FLAGB is disabled to reduce current draw from the supply. On/Off Control The ON pin controls the state of the switch. The FPF2024- FPF2027 series features both active high and low configurations to accommodate various application requirements. FPF2024, FPF2026 and FPF2027 are active high switches while the FPF2025 is an active low device. Applying a continuous high or low signal depending on the switch configuration, will hold the switch in the ON state. The load switch will move into © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 10 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Description of Operation Thermal Shutdown The current limit function ensures that the current through the switch does not exceed a maximum value while not limiting at less than a minimum value. The minimum current at which the parts will limit the load current is internally set to 100 mA. The Thermal Shutdown protects the device from internally or externally generated excessive temperatures. The Thermal shutdown feature is disabled during Sleep mode. However, excessive load currents that may result in high power dissipation will be detected during Sleep mode and will activate the full function Wakeup mode, which has thermal shutdown protection. During an over-temperature condition the FLAGB is pulled low and the switch is turned-off. If the temperature of the die drops below the threshold temperature, the switch automatically turns on again, To avoid unwanted thermal oscillations, a 10°C (typical) thermal hysteresis is implemented between thermal shutdown entry and exit temperatures. The switch current limiting circuitry is active at all times (Sleep and Wakeup mode) and protects the FPF2024FPF2027 against excessive load currents in all modes. The proprietary current limiting circuit responds to an over-current condition in 15 μs (typical). Under-Voltage Lockout (UVLO) The under-voltage lockout feature turns-off the switch if the input voltage drops below the under-voltage lockout threshold. With the ON pin active, the input voltage rising above the under-voltage lockout threshold will cause a controlled turn-on of the switch and will limit current over-shoots. The UVLO feature is disabled during Sleep mode. If device is in the UVLO condition, FLAGB goes low and indicates the fault. If the input voltage goes below UVLO voltage but remains above 1.3 V (typical) during Sleep mode, the switch is kept on until the next Wakeup cycle, where the UVLO violation will be detected. If the input voltage falls below 1.3 V in Sleep mode, the switch is immediately turned off. Figure 25. © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 State Diagram with Blanking and Auto-Restart (FPF2024/5) www.fairchildsemi.com 11 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Current Limiting © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Figure 26. State Diagram with Blanking Only (No Auto-Restart FPF2026) www.fairchildsemi.com 12 © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Figure 27. State Diagram with No Blanking (FPF2027) www.fairchildsemi.com 13 This power dissipation is significant enough that it will activate the thermal shutdown protection, and the part will cycle in and out of thermal shutdown so long as the ON pin is active and the output short is present. Input Capacitor To limit the voltage drop on the input supply caused by transient in-rush currents when the switch is turned on into a discharged load capacitor or a short-circuit, a capacitor is recommended to be placed between V IN and GND. The FPF2024-FPF2027 series feature a slow turn-on to limit the inrush current and requires a smaller input capacitor. A 1 µF ceramic capacitor, CIN, placed close to the pins is typically sufficient. Higher values of CIN can be used to further reduce the voltage drop. Improving Thermal Performance An improper layout could result in higher junction temperature and ultimately trigger the thermal shutdown protection feature. This concern applies particularly significant for the FPF2027 where the switch is in constant current mode in the overload conditions. Output Capacitor The following techniques have been identified to improve the thermal performance of this family of devices. These techniques are listed in order of the significance of their impact. A 0.1 µF capacitor COUT, should be placed between VOUT and GND. This capacitor will prevent parasitic board inductances from forcing VOUT below GND when the switch turns-off. For the FPF2024, FPF2025 and FPF2026, the total output capacitance needs to be kept below a maximum value, COUT(MAX), to prevent the part from registering an over-current condition beyond the Blanking Time and turning-off the switch. The maximum output capacitance can be determined from the following formula:  NC pin can be connected to the GND plane to improve thermal performance.  The VIN, VOUT and GND pins will dissipate most of the heat generated during a high load current condition. Using wide traces will help minimize parasitic electrical effects, along with minimizing the case to ambient thermal impedance. The layout suggested in Figure 28 provides each pin with adequate copper so that heat may be transferred out of the device as efficiently as possible. The lowpower FLAGB and ON pin traces may be laid-out to maximize the area available to the ground pad.  Placing the input and output capacitors as close to the device as possible also contributes to heat dissipation, particularly during high load currents. (1) Power Dissipation During normal operation as a switch, the power dissipation is small and has little effect on the operating temperature of the part. The maximum power dissipation while switch is in normal operation occurs just before a part enters the current limit. This may be calculated using the formula bellow: FPF202X Demo Board FPF202X Demo board has components and circuitry to demonstrate the functions and features of the FPF202X load switch family. An N-Channel MOSFET(Q), in series with a 7.5 Ω resistor, are connected between VOUT and the GND pin of the device. By turning on the Q transistor, the 7.5 Ω is loaded to the output voltage and simulates an over-current condition. The R2 resistor is connected between FLAGB pin and input voltage as pull-up resistor for FPF2024, FPF2026 and FPF2027 devices. The FPF2025 does not require a pull-up resistor due to its CMOS output structure. (2) If the part goes into current limit, the maximum power dissipation occurs when the output of switch is shorted to ground. For the FPF2024 and FPF2025, the power dissipation will scale with the Auto-Restart Time, tRSTRT, and the Over Current Blanking Time, tBLANK. In this case the maximum power dissipated for the FPF2024 and FPF2025 is: The thermal performance of the board is improved using the techniques recommended in the layout recommendations section of datasheet. (3) Take note that this is below the maximum package power dissipation, and the thermal shutdown feature protection provides additional safety to protect the part from damage due to excessive heating. The junction temperature is only able to increase to the thermal shutdown threshold. Once this temperature has been reached, toggling ON will have no effect until the junction temperature drops below the thermal shutdown exit temperature. For the FPF2027, a short on the output will cause the part to operate in a constant current state dissipating a worst case power of: Figure 28. (4) FPF2020X Proper Layout Output of FPF2027 is shorted to GND. © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 14 PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Application Information Top Layer Figure 31. Figure 30. SST Figure 32. PFPF2024/25/26/27 — Full Function Load Switch with 100 mA Current Limit Figure 29. Bottom Layer TOP, SST and SMT The information below pertains to the WLCSP outline drawing on the following page. Product Specifications Product D E X Y FPF2024/5/6/7 1.500 ±0.030 1.000 ±0.030 0.240 0.240 © 2008 Fairchild Semiconductor Corporation FPF2024/25/26/27 • Rev. 1.1 www.fairchildsemi.com 15 0.03 C E 2X F A (Ø0.250) Cu Pad (Ø0.350) SOLDER MASK OPENING B A1 (1.00) BALL A1 INDEX AREA D (0.50) 0.03 C 2X TOP VIEW RECOMMENDED LAND PATTERN (NSMD PAD TYPE) 0.06 C 0.625 0.539 0.05 C C 0.332±0.018 0.250±0.025 E SEATING PLANE D SIDE VIEWS NOTES: A. NO JEDEC REGISTRATION APPLIES. 0.005 Ø0.315 +/- .025 6X 0.50 C 1.00 B A 0.50 (Y) ±0.018 1 2 F (X) ±0.018 BOTTOM VIEW C A B B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCE PER ASMEY14.5M, 1994. D. DATUM C IS DEFINED BY THE SPHERICAL CROWNS OF THE BALLS. E. PACKAGE NOMINAL HEIGHT IS 582 MICRONS ±43 MICRONS (539-625 MICRONS). F. FOR DIMENSIONS D, E, X, AND Y SEE PRODUCT DATASHEET. G. DRAWING FILNAME: MKT-UC006AFrev3. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com © Semiconductor Components Industries, LLC N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com