FXLH1T45
Level Translator, 1-Bit
Bidirectional
Configurable Voltage Supplies and
Bushold Data Inputs
www.onsemi.com
The FXLH1T45 is a single bit configurable dual−voltage supply
translator designed for both uni−directional and bi−directional voltage
translation between two logic levels. The device allows translation
between voltages as high as 3.6 V to as low as 1.1 V. The A port tracks
the VCCA level, and the B port tracks the VCCB level. This allows for
bi−directional voltage translation over a variety of voltage levels:
1.2 V, 1.5 V, 1.8 V, 2.5 V and 3.3 V.
The device remains in 3−STATE until both VCCs reach active levels
allowing either VCC to be powered−up first. Internal power down
control circuits place the device in 3−STATE if either VCC is removed.
The Transmit/Receive (T/R) input determines the direction of data
flow through the device. The FXLH1T45 is designed so that the
control pin (T/R) is supplied by VCCA.
SIP6 1.45x1.0
CASE 127EB
MARKING DIAGRAM
Features
XDKK
XYZ
• Bi−directional Interface between any 2 Levels from 1.1 V to 3.6 V
• Fully Configurable: Inputs Track VCC level
• Non−preferential Power−up Sequencing; either VCC may be
•
•
•
•
•
•
•
Powered−up First
Outputs Remain in 3−STATE until Active VCC Level is Reached
Outputs Switch to 3−STATE if either VCC is at GND
Power Off Protection
Bushold On Data Inputs Eliminates the Need for External
Pull−up/Pull−down Resistors
Control Input (T/R) Levels are Referenced to VCCA Voltage
Packaged in the MicroPak 6 SIP6 (1.0 mm x 1.45 mm)
ESD Protections Exceeds:
♦ 4 kV HBM ESD
(per JESD22−A114 & Mil Std 883e 3015.7)
♦ 8 kV HBM I/O to GND ESD
(per JESD22−A114 & Mil Std 883e 3015.7)
♦ 1 kV CDM ESD (per ESD STM 5.3)
♦ 200 V MM ESD (per JESD22−A115 & ESD STM5.2)
© Semiconductor Components Industries, LLC, 2006
March, 2019 − Rev. 2
1
XD
KK
XY
Z
= Device Code
= Lot Code
= Numeric Date Code
= Assembly Plant Code
ORDERING INFORMATION
See detailed ordering and shipping information on page 9 of
this data sheet.
Publication Order Number:
FXLH1T45/D
FXLH1T45
FUNCTIONAL DIAGRAM
POWER−UP/POWER−DOWN SEQUENCING
FXL translators offer an advantage in that either VCC may
be powered up first. This benefit derives from the chip
design. When either VCC is at 0V, outputs are in a
HIGH−Impedance state. To ensure that bus contention,
excessive currents, or oscillations do not occur, a proper
power−up sequence is recommended.
The recommended power−up sequence is the following:
1. Apply power to either VCC
2. Apply power to the T/R input (Logic HIGH for
A−to−B operation; Logic LOW for B−to−A
operation) and to the respective data inputs (A Port
or B Port). This may occur at the same time as
Step 1
3. Apply power to other VCC
VCCB
VCCA
A
B
T/R
PINOUT
VCCA
1
6
VCCB
GND
2
5
T/R
A
3
4
B
The recommended power−down sequence is the
following:
4. Remove power from either VCC
5. Remove power from other VCC
(Top Through View)
PIN ASSIGNMENT
Pin Number
Terminal Name
1
VCCA
2
GND
3
A
4
B
5
T/R
6
VCCB
PIN DESCRIPTIONS
Pin Names
Description
T/R
Transmit/Receive Input
A
Side A Input or Output
B
Side B Input or Output
VCCA
Side A Power Supply
VCCB
Side B Power Supply
FUNCTION TABLE
Inputs (T/R)
Outputs
L
Bus B Data to Bus A
H
Bus A Data to Bus B
H = HIGH Logic Level L = LOW Logic Level
www.onsemi.com
2
FXLH1T45
ABSOLUTE MAXIMUM RATINGS
Symbol
VCCA, VCCB
Parameter
Rating
−0.5 V to +4.6 V
Supply Voltage
VI
DC Input Voltage
I/O Port A
I/O Port B
Control Input (T/R)
−0.5 V to +4.6 V
−0.5 V to +4.6 V
−0.5 V to +4.6 V
VO
Output Voltage (Note 1)
Outputs 3−STATE
Outputs Active (An)
Outputs Active (Bn)
−0.5 V to +4.6 V
−0.5 V to VCCA + 0.5 V
−0.5 V to VCCB + 0.5 V
IIK
DC Input Diode Current @ VI < 0 V
IOK
IOH / IOL
ICC
TSTG
DC Output Diode Current @
VO < 0 V
VO > VCC
−50 mA
−50 mA
+50 mA
−50 mA / +50 mA
DC Output Source/Sink Current
DC VCC or Ground Current per Supply Pin
±100 mA
−65°C to +150°C
Storage Temperature Range
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
RECOMMENDED OPERATING CONDITIONS (Note 2)
Symbol
VCCA or VCCB
Vi
Vo
TA
Dt/ DV
Parameter
Power Supply Operating
Rating
1.1 V to 3.6 V
Input Voltage
Port A
Port B
Control Input (T/R)
0.0 V to 3.6 V
0.0 V to 3.6 V
0.0 V to VCCA
Output Current in IOH/IOL with VCC @
3.0 V to 3.6 V
2.3 V to 2.7 V
1.65 V to 1.95 V
1.4 V to 1.65 V
1.1 V to 1.4 V
Free Air Operating Temperature
Maximum Input Edge Rate VCCA/B = 1.1 V to 3.6 V
±24 mA
±18 mA
±6 mA
±2 mA
±0.5 mA
−40°C to +125°C
10 ns/V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
NOTES:
1. IO Absolute Maximum Rating must be observed.
2. All unused inputs and I/O pins must be held at VCCI or GND.
www.onsemi.com
3
FXLH1T45
DC ELECTRICAL CHARACTERISTICS (TA = −40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C)
Symbol
VIH
Parameter
High Level Input Voltage
(Note 3)
Conditions
Data Inputs An, Bn
VCCI (V)
VCCO (V)
Min.
Typ.
Max.
Units
2.7–3.6
1.1–3.6
2.0
−
−
V
2.3–2.7
1.6
−
−
1.65–2.3
0.65 x VCCI
−
−
1.4–1.65
0.65 x VCCI
−
−
0.9 x VCCI
−
−
1.1–1.4
Control Pin T/R
(Referenced to VCCA)
2.7–3.6
1.1–3.6
2.0
−
−
2.3–2.7
1.6
−
−
1.65–2.3
0.65 x VCCA
−
−
1.4–1.65
0.65 x VCCA
−
−
0.9 x VCCA
−
−
−
−
0.8
2.3–2.7
−
−
0.7
1.65–2.3
−
−
0.35 x VCCI
1.4–1.65
−
−
0.35 x VCCI
−
−
0.1 x VCCI
1.1–1.4
VIL
Low Level Input Voltage
(Note 3)
Data Inputs An, Bn
2.7–3.6
1.1–3.6
1.1–1.4
Control Pin T/R
(Referenced to VCCA)
VOH
VOL
II
High Level Output Voltage
(Note 4)
Low Level Output Voltage
(Note 4)
Input Leakage Current
Control Pins
2.7–3.6
1.1–3.6
−
−
0.8
2.3–2.7
−
−
0.7
1.65–2.3
−
−
0.35 x VCCA
1.4–1.65
−
−
0.35 x VCCA
1.1–1.4
−
−
0.1 x VCCA
IOH = −100 mA
1.1–3.6
1.1–3.6
VCCO–0.2
−
−
IOH = −12 mA
2.7
2.7
2.2
−
−
IOH = −18 mA
3.0
3.0
2.4
−
−
IOH = −24 mA
3.0
3.0
2.2
−
−
IOH = −6 mA
2.3
2.3
2.0
−
−
IOH = −12 mA
2.3
2.3
1.8
−
−
IOH = −18 mA
2.3
2.3
1.7
−
−
IOH = −6 mA
1.65
1.65
1.25
−
−
IOH = −2 mA
1.4
1.4
1.05
−
−
IOH = −0.5 mA
1.1
1.1
0.75 x VCCO
−
−
IOL = 100 μA
1.1–3.6
1.1–3.6
−
−
0.2
IOL = 12 mA
2.7
2.7
−
−
0.4
IOL = 18 mA
3.0
3.0
−
−
0.4
IOL = 24 mA
3.0
3.0
−
−
0.55
IOL =12 mA
2.3
2.3
−
−
0.4
IOL = 18 mA
2.3
2.3
−
−
0.6
IOL = 6 mA
1.65
1.65
−
−
0.3
IOL = 2 mA
1.4
1.4
−
−
0.35
IOL = 0.5 mA
1.1
1.1
−
−
0.3 x VCCO
1.1–3.6
3.6
−
−
±1.0
VI = VCCA or GND
www.onsemi.com
4
V
V
V
mA
FXLH1T45
DC ELECTRICAL CHARACTERISTICS (continued) (TA = −40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C)
Symbol
II(HOLD)
II(OD)
IOFF
IOZ
Parameter
Bushold Input Minimum
Drive Current
Bushold Input Over−Drive
Current to Change State
Current−to−Change
Power Off Leakage Current
3−STATE Output Leakage
VCCI (V) VCCO (V)
Conditions
Min.
Typ.
Max.
Units
75.0
−
−
mA
VIN = 0.8 V,
TA = −40°C to +85°C
3.0
3.0
VIN = 0.8 V
3.0
3.0
60.0
−
−
VIN = 2 V,
TA = −40°C to +85°C
3.0
3.0
−75.0
−
−
VIN = 2 V
3.0
3.0
−60
−
−
VIN = 0.7 V
2.3
2.3
45.0
−
−
VIN = 1.6 V
2.3
2.3
−45.0
−
−
VIN = 0.57 V
1.65
1.65
25.0
−
−
VIN = 1.07 V
1.65
1.65
−25.0
−
−
VIN = 0.49 V
1.4
1.4
10.0
−
−
VIN = 0.91 V
1.4
1.4
−10.0
−
−
VIN = 0.11 V
1.1
1.1
−
4.0
−
VIN = 0.99 V
1.1
1.1
−
−4.0
−
(Note 5)
3.6
3.6
450
−
−
(Note 6)
3.6
3.6
−450
–
–
(Note 5)
2.7
2.7
300
–
–
(Note 6)
2.7
2.7
−300
–
–
(Note 5)
1.95
1.95
200
–
–
(Note 6)
1.95
1.95
−200
–
–
(Note 5)
1.6
1.6
120
–
–
(Note 6)
1.6
1.6
−120
–
–
(Note 5)
1.4
1.4
80.0
–
–
(Note 6)
1.4
1.4
−80.0
–
–
An, VCCA = VCCI,
VI = 0 V to 3.6 V
0
3.6
–
–
±10.0
Bn, VCCB = VCCI,
VI = 0 V to 3.6 V
0
3.6
−
−
±10.0
An, VCCA = VCCO,
VO = 0 V or 3.6 V
0
3.6
−
−
±10.0
Bn, VCCB = VCCO,
VO = 0 V or 3.6 V
0
3.6
–
–
±10.0
mA
mA
mA
ICCA/B
Quiescent Supply Current
(Note 7)
VI = VCCI or GND; IO = 0
1.1–3.6
1.1–3.6
−
−
20.0
mA
ICCA
Quiescent Supply Current
VI = VCCA or GND; IO = 0
0
1.1–3.6
−
−
−10.0
mA
VI = VCCA or GND; IO = 0
1.1–3.6
0
–
–
10.0
ICCB
Quiescent Supply Current
VI = VCCB or GND; IO = 0
1.1–3.6
0
−
−
−10.0
VI = VCCB or GND; IO = 0
0
1.1–3.6
–
–
10.0
3.6
3.6
–
–
500
DICCA/B
Increase in ICC per Input;
Other Inputs at VCC or GND
VIH = 3.0 V
mA
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
NOTES:
3. VCCI = the VCC associated with the data input under test.
4. VCCO = the VCC associated with the output under test.
5. An external driver must source at least the specified current to switch LOW−to−HIGH.
6. An external driver must source at least the specified current to switch HIGH−to−LOW.
7. Reflects current per supply, VCCA or VCCB.
www.onsemi.com
5
FXLH1T45
AC Electrical Characteristics (TA = −40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C.)
VCCA = 3.0 V to 3.6 V
VCCB =
3.0 V to 3.6 V
VCCB =
2.3 V to 2.7 V
VCCB = 1.65 V
to 1.95 V
VCCB =
1.4 V to 1.6 V
VCCB =
1.1 V to 1.3 V
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Units
tPLH, tPHL
Propagation Delay A to B
0.2
3.5
0.3
3.9
0.5
5.4
0.6
6.8
1.4
22.0
ns
Propagation Delay B to A
0.2
3.5
0.2
3.8
0.3
4.0
0.5
4.3
0.8
13.0
tPZH, tPZL
(Note 8)
Output Enable T/R to B
0.4
7.2
0.5
7.6
0.7
9.1
0.8
10.5
1.6
25.7
Output Enable T/R to A
0.4
7.3
0.4
7.8
1.0
8.8
2.0
10.5
2.8
30.0
tPHZ, tPLZ
Output Disable T/R to B
−
3.9
−
5.3
−
7.3
−
7.6
−
17.0
−
5.6
−
4.2
−
6.3
−
6.9
−
17.0
−
4.9
−
5.8
−
3.7
−
5.7
−
3.7
−
4.6
−
4.8
−
4.5
−
4.9
−
4.5
TA = −40°C to +85°C
Output Disable T/R to A
TA = −40°C to +85°C
ns
ns
VCCA = 2.3 V to 2.7 V
VCCB =
3.0 V to 3.6 V
VCCB =
2.3 V to 2.7 V
VCCB = 1.65 V
to 1.95 V
VCCB =
1.4 V to 1.6 V
VCCB =
1.1 V to 1.3 V
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Units
tPLH, tPHL
Propagation Delay A to B
0.2
3.8
0.4
4.2
0.5
5.6
0.8
6.9
1.4
22.0
ns
Propagation Delay B to A
0.3
3.9
0.4
4.2
0.5
4.5
0.5
4.8
1.0
7.0
tPZH, tPZL
(Note 8)
Output Enable T/R to B
0.4
7.8
0.6
8.2
0.7
9.6
1.0
10.9
1.6
26.0
Output Enable T/R to A
0.5
8.0
0.6
8.5
1.2
9.3
2.0
11.5
3.0
24.0
tPHZ, tPLZ
Output Disable T/R to B
−
4.1
−
4.3
−
7.0
−
6.7
−
17.0
−
5.7
−
4.3
−
5.7
−
6.7
−
17.0
−
5.3
−
5.9
−
4.0
−
6.0
−
5.9
−
4.8
−
4.8
−
4.8
−
5.0
−
4.8
TA = −40°C to +85°C
Output Disable T/R to A
TA = −40°C to +85°C
ns
ns
VCCA = 1.65 V to 1.95 V
VCCB =
3.0 V to 3.6 V
VCCB =
2.3 V to 2.7 V
VCCB = 1.65 V
to 1.95 V
VCCB =
1.4 V to 1.6 V
VCCB =
1.1 V to 1.3 V
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Units
tPLH, tPHL
Propagation Delay A to B
0.3
4.0
0.5
4.5
0.8
5.7
0.9
7.1
1.5
22.0
ns
Propagation Delay B to A
0.5
5.4
0.5
5.6
0.8
5.7
1.0
6.0
1.2
8.0
tPZH, tPZL
(Note 8)
Output Enable T/R to B
0.8
9.0
1.0
9.5
1.3
10.7
1.4
12.1
2.0
27.0
Output Enable T/R to A
0.7
10.5
0.7
10.8
1.6
10.9
2.5
13.0
3.2
25.0
tPHZ, tPLZ
Output Disable T/R to B
−
5.1
−
5.2
−
6.7
−
7.0
−
17.0
−
5.7
−
5.6
−
5.8
−
7.0
−
17.0
−
5.0
−
6.5
−
5.0
−
5.0
−
5.0
−
5.0
−
5.0
−
5.0
−
5.0
−
5.0
TA = −40°C to +85°C
Output Disable T/R to A
TA = −40°C to +85°C
www.onsemi.com
6
ns
ns
FXLH1T45
VCCA = 1.4 V to 1.6 V
VCCB =
3.0 V to 3.6 V
VCCB =
2.3 V to 2.7 V
VCCB = 1.65 V
to 1.95 V
VCCB =
1.4 V to 1.6 V
VCCB =
1.1 V to 1.3 V
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Units
tPLH, tPHL
Propagation Delay A to B
0.5
4.3
0.5
4.8
1.0
6.0
1.0
7.3
1.5
22.0
ns
Propagation Delay B to A
0.6
6.8
0.8
6.9
0.9
7.1
1.0
7.3
1.3
9.5
tPZH, tPZL
(Note 8)
Output Enable T/R to B
1.5
10.3
1.5
10.8
2.0
12.0
2.0
13.3
2.5
28.0
Output Enable T/R to A
1.0
12.9
1.2
13.1
1.8
13.3
2.5
14.8
3.3
27.5
tPHZ, tPLZ
Output Disable T/R to B
−
6.1
−
6.2
−
6.2
−
7.5
−
18.0
−
6.1
−
6.2
−
6.2
−
7.5
−
18.0
−
8.0
−
7.5
−
6.0
−
6.0
−
6.0
−
6.5
−
6.3
−
6.0
−
6.0
−
6.0
TA = −40°C to +85°C
Output Disable T/R to A
TA = −40°C to +85°C
ns
ns
VCCA = 1.1 V to 1.3 V
VCCB =
3.0 V to 3.6 V
VCCB =
2.3 V to 2.7 V
VCCB = 1.65 V
to 1.95 V
VCCB =
1.4 V to 1.6 V
VCCB =
1.1 V to 1.3 V
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Units
tPLH, tPHL
Propagation Delay A to B
0.8
13.0
1.0
7.0
1.2
8.0
1.3
9.5
2.0
24.0
ns
Propagation Delay B to A
1.4
22.0
1.4
22.0
1.5
22.0
1.5
22.0
2.0
24.0
tPZH, tPZL
(Note 8)
Output Enable T/R to B
2.8
28.0
3.0
19.0
3.2
20.0
3.3
21.5
4.0
36.0
Output Enable T/R to A
2.4
37.0
2.1
29.0
2.5
30.0
3.5
32.0
4.0
44.0
tPHZ, tPLZ
Output Disable T/R to B
−
15.0
−
7.0
−
8.0
−
10.0
−
20.0
−
15.0
−
7.0
−
8.0
−
10.0
−
20.0
−
15.0
−
12.0
−
12.0
−
12.0
−
12.0
−
15.0
−
12.0
−
12.0
−
12.0
−
12.0
TA = −40°C to +85°C
Output Disable T/R to A
TA = −40°C to +85°C
ns
ns
NOTES:
8. The enable time, tPZH or tPZL, is the time for the FXLH1T45 to return to active operation after a direction change. The enable time specifies the
worst−case delay from the time the T/R pin is switched until a valid output signal is expected. For example, to change direction to B−to−A
operation, the T/R pin is switched from HIGH−to−LOW. The enable time for this case is found by adding the disable time for T/R to B to the
propagation delay for B to A. The formulas for calculating enable times are the following:
tPZH (T/R to A) = tPLZ (T/R to B) + tPLH (B to A)
tPZL (T/R to A) = tPHZ (T/R to B) + tPHL (B to A)
tPZH (T/R to B) = tPLZ (T/R to A) + tPLH (A to B)
tPZL (T/R to B) = tPHZ (T/R to A) + tPHL (A to B)
CAPACITANCE
TA = +25_C
Symbol
Parameter
Conditions
Typical
Units
CIN
Input Capacitance Control Pin (T/R)
VCCA = VCCB = 3.3 V, VI = 0 V or VCCA/B
4.0
pF
CI/O
Input/Output Capacitance An, Bn Ports
VCCA = VCCB = 3.3 V, VI = 0 V or VCCA/B
5.0
pF
CPD
Power Dissipation Capacitance
VCCA = VCCB = 3.3 V, VI = 0 V or VCC, F = 10 MHz
20.0
pF
www.onsemi.com
7
FXLH1T45
AC Loading and Waveforms
VCC
OPEN
Rtr1
TEST
SIGNAL
CL
tPLH, tPHL
tPHZ
tPLZ
GND
VCC x 2
DUT
RL
Figure 1. AC Test Circuit
AC TEST CIRCUIT
Test
Switch
tPLH, tPHL
OPEN
tPLZ
VCCO x 2 at VCCO = 3.3 ±0.3 V, 2.5 V ±0.2 V, 1.8 V ±0.15 V, 1.5 V ±0.1 V, 1.2 V ±0.1 V
tPHZ
GND
AC LOAD TABLE
VCCO
CL
RL
Rtr1
1.2 V ±0.1 V
15 pF
2 kΩ
2 kΩ
1.5 V ±0.1 V
15 pF
2 kΩ
2 kΩ
1.8 V ±0.15 V
15 pF
2 kΩ
2 kΩ
2.5 V ±0.2 V
15 pF
2 kΩ
2 kΩ
15 pF
2 kΩ
2 kΩ
3.3 V ±0.3 V
DATA
IN
VCCI
Vmi
tpxx
DATA
OUT
DIRECTION
CONTROL
GND
tpxx
Vmo
Vmi
tPZL
VCCO
DATA
OUT
Input t R = t F = 2.0 ns, 10% to 90%
Input t R = t F = 2.5 ns, 10% to 90%, @ VI = 3.0 V to 3.6 V only
tPLZ
Vmo
VCCA
GND
VY
VOL
Input t R = t F = 2.0 ns, 10% to 90%
Input t R = t F = 2.5 ns, 10% to 90%, @ V I = 3.0 V to 3.6 V only
Figure 2. Waveform for Inverting
and Non−Inverting Functions
Figure 3. 3−STATE Output Low Enable
and Disable Times for Low Voltage Logic
DIRECTION
CONTROL
Vmi
tPZH
DATA
OUT
tPHZ
Vmo
VCCA
GND
VOH
VX
Input t R = t F = 2.0 ns, 10% to 90%
Input t R = t F = 2.5 ns, 10% to 90%, @ V I = 3.0 V to 3.6 V only
Figure 4. 3−STATE Output High Enable and Disable Times for Low Voltage Logic
VCC
Symbol
3.3V ± 0.3V
2.5 V ± 0.2 V
1.8 V ± 0.15 V
1.5 V ± 0.1 V
1.2 V ± 0.1 V
Vmi
VCCI / 2
VCCI / 2
VCCI / 2
VCCI / 2
VCCI / 2
Vmo
VCCO / 2
VCCO / 2
VCCO / 2
VCCO / 2
VCCO / 2
VX
VOH − 0.3 V
VOH − 0.15 V
VOH − 0.15 V
VOH− 0.1 V
VOH − 0.1 V
VY
VOL + 0.3 V
VOL + 0.15 V
VOL + 0.15 V
VOL+ 0.1 V
VOL + 0.1 V
9. For Vmi: VCCI = VCCA for Control Pin T/R or VCCA / 2.
www.onsemi.com
8
FXLH1T45
ORDERING INFORMATION
Order Number
Case Number
Pb−Free
Package Description
Supplied As
FXLH1T45L6X
127EB
Yes
6−Lead MicroPak/SIP6, 1.0 mm Wide
5k Units on Tape and Reel
Tape and Reel Specification
TAPE FORMAT FOR MICROPAK
Package Designator
Tape Section
Number Cavities
Cavity Status
Cover Tape Status
L6X
Leader (Start End)
125 (typ)
Empty
Sealed
Carrier
5000
Filled
Sealed
Trailer (Hub End)
75 (typ)
Empty
Sealed
Tape Dimensions Millimeters
Reel Dimensions Inches (Millimeters)
Tape Size
A
B
C
D
N
W1
W2
W3
8 mm
7.0
(177.8)
0.059
(1.50)
0.512
(13.00)
0.795
(20.20)
2.165
(55.00)
0.331 + 0.059/−0.000
(8.40 + 1.50 /−0.00)
0.567
(14.40)
W1 + 0.078 /−0.039
(W1 + 2.00 /−1.00)
www.onsemi.com
9
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SIP6 1.45X1.0
CASE 127EB
ISSUE O
DOCUMENT NUMBER:
DESCRIPTION:
98AON13590G
SIP6 1.45X1.0
DATE 31 AUG 2016
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
