GTLP6C817MTCX

Revised December 2000 GTLP6C817 Low Drive GTLP/LVTTL 1:6 Clock Driver General Description Features The GTLP6C817 is a low drive clock driver that provides TTL to GTLP signal level translation (and vice versa). The device provides a high speed interface between cards operating at TTL logic levels and a backplane operating at GTLP logic levels. High speed backplane operation is a direct result of GTLP’s reduced output swing ( VCC +50 mA ESD Rating > 2000V Storage Temperature (TSTG) 4.75V to 5.25V VCCT Bus Termination Voltage (VTT) DC Output Sink Current into OA Port IOL VCC −40°C to +85°C Operating Temperature (TA) Note 1: Absolute Maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum rated conditions is not implied. −65°C to +150°C Note 2: Io Absolute Maximum Rating must be observed. Note 3: Unused input must be held HIGH or LOW. DC Electrical Characteristics Over Recommended Operating Free-Air Temperature Range, VREF = 1.0V (unless otherwise noted). Symbol VIH VIL Test Conditions Min Typ VREF + 0.05 GTLPIN Others 2.0 GTLPIN 0.0 VTT VREF − 0.05 Others 0.8 VREF GTLP 1.0 (Note 5) GTL 0.8 VTT GTLP 1.5 (Note 5) GTL 1.2 VCC = 4.75V VIK VCCT = 3.15V VOH VOL VOL II IOFF IOZH IOZL OAn Port OAn Port Max (Note 4) II = −18 mA IOH = −100 µA VCCT = 3.15V IOH = −6 mA 2.4 IOH = −12 mA 2.2 V IOL = 100 µA 0.2 VCCT = 3.15V IOL = 6 mA 0.4 IOL = 12 mA 0.5 IOL = 100 µA 0.2 VCCT = 3.15V IOL = 40 mA 0.5 TTLIN/ VCC = 5.25V VI = 5.25V 5 Control Pins VCCT = 3.45V VI = 0V −5 GTLPIN VCC = 5.25V VI = VTT 5 VCCT = 3.45V VI = 0 −5 VI or VO = 0V to 5.25V 30 GTLPIN, OBn Port VCCT = 0 VI or VO = 0 to VTT 30 OAn Port VCC = 5.25V VO = 5.25V 5 OBn Port VCCT = 3.45V VO = 1.5V 5 OAn Port VCC = 5.25V VO = 0 OBn Port VCCT = 3.45V VO = 0 3 V VCC− 0.2 VCC = 4.75V TTLIN, OAn Port, Control Pins VCC = 0 V V VCC = 4.75V OBn Port V V −1.2 VCC = 4.75V Units −5 V V µA µA µA µA µA www.fairchildsemi.com GTLP6C817 Absolute Maximum Ratings(Note 1) GTLP6C817 DC Electrical Characteristics Symbol (Continued) Min Test Conditions Typ Max (Note 4) IPU/PD All Ports VCC = VCCT = 0 to 1.5V OE = Don’t Care 30 ICC (5V) OAn or VCC = 5.25V Outputs HIGH 10 OBn Ports VCCT = 3.45V Outputs LOW 10 Outputs Disabled 10 Units µA mA VI = VCC or GND ICC (3V) OAn or VCC = 5.25V Outputs HIGH, LOW 45 OBn Ports VCCT = 3.45V Outputs Disabled 45 µA 1 mA pF VI = VCC or GND ∆ICC VCC = 5.25V TTLIN VI = VCC−2.1 VCCT = 3.45V CIN Control Pins/GTLPIN/TTLIN VI = VCC or 0 3 3.5 COUT OAn Port VI = VCC or 0 3 4.5 OBn Port VI = VCC or 0 4 5 pF Note 4: All typical values are at VCC = 5.0V VCCT = 3.3V and TA = 25°C. Note 5: GTLP VREF and VTT are specified to 2% tolerance since signal integrity and noise margin can be significantly degraded if these supplies are noisy. In addition, VTT and RTERM can be adjusted to accommodate backplane impedances other than 50Ω, within the boundaries of not exceeding the DC Absolute IOL ratings. Similarly VREF can be adjusted to compensate for changes in V TT. AC Electrical Characteristics Over recommended range of supply voltage and operating free air temperature. VREF = 1.0V (unless otherwise noted). CL = 30 pF for OBn Port and CL = 50 pF for OAn Port. From To (Input) (Output) TTLIN OBn Min Typ Max Symbol tPLH Units (Note 6) tPLH 2.3 4.7 1.5 4.6 ns tPHL OEB OBn 2.4 4.8 1.6 4.7 ns tPHL tRISE Transition Time, OB Outputs (20% to 80%) 1.7 ns tFALL Transition Time, OB outputs (20% to 80%) 2.1 ns tRISE Transition Time, OA outputs (10% to 90%) 2.7 ns tFALL Transition Time, OA outputs (10% to 90%) 2.2 ns tPZH, tPZL OEA OAn tPLH GTLPIN OAn 6.5 6.5 3.1 6.6 2.8 6.0 ns tPHL Note 6: All typical values are at VCC = 5.0V and TA = 25°C. www.fairchildsemi.com 2.4 2.0 ns tPLZ, tPHZ 4 Over recommended ranges of supply voltage and operating free-air temperature VREF = 1.0V (unless otherwise noted). CL = 30 pF for B Port and CL = 50 pF for A Port. Symbol From To (Input) (Output) Min Typ (Note 7) Max Unit tOSLH (Note 8) A B .05 .4 tOSHL (Note 8) A B .05 .4 tPS (Note 9) A B 0.5 1.0 ns tPV(HL) (Note 10) A B .7 ns (Note 11) ns tOSLH (Note 8) B A .12 .5 tOSHL (Note 8) B A .12 .5 tOST (Note 8) B A .6 1.0 ns tPS (Note 9) B A 0.5 1.0 ns tPV (Note 10) B A 1.2 ns ns Note 7: All typical values are at VCC = 5.0V and TA = 25°C. Note 8: tOSHL/tOSLH and tOST - Output-to-Output skew is defined as the absolute value of the difference between the actual propagation delay for all outputs within the same packaged device. The specifications are given for specific worst case VCC and temperature and apply to any outputs switching in the same direction either HIGH-to-LOW (tOSHL) or LOW-to-HIGH (tOSLH) or in opposite directions both HL and LH (tOST). This parameter is guaranteed by design and statistical process distribution. Actual skew values between the GTLP outputs could vary on the backplane due to the loading and impedance seen by the device. Note 9: tPS - Pin or Transition skew is defined as the difference between the LOW-to-HIGH transition and the HIGH-to-LOW transition on the same pin. The parameter is measured across all the outputs of the same chip is specified for a specific worst case VCC and temperature. This parameter is guaranteed by design and statistical process distribution. Actual skew values between the GTLP outputs could vary on the backplane due to the loading and impedance seen by the device. Note 10: tPV - Part-to-Part skew is defined as the absolute value of the difference between the actual propagation design for all outputs from device-todevice. The parameter is specified for a specific worst case VCC and temperature. This parameter is guaranteed by design and statistical process distribution. Actual skew values between the GTLP output could vary on the backplane due to the loading and impedance seen by the device. Note 11: Due to the open drain structure on GTLP outputs, tOST and tPV(LH) in the A-to-B direction are not specified. Skew on these paths is dependent on the VTT and RT values in the actual application. 5 www.fairchildsemi.com GTLP6C817 Extended Electrical Characteristics GTLP6C817 Test Circuit and Timing Waveforms Test Circuit for A Outputs Test Circuit for B Outputs Note A: CL includes probes and jig capacitance. Note A: CL includes probes and jig capacitance. Note B: For B Port CL = 30 pF is used for worst case. Voltage Waveform - Propagation Delay Times Voltage Waveform - Enable and Disable Times Output Waveform 1 is for an output with internal conditions such that the output is LOW except when disabled by the control output Output Waveforms 2 is for an output with internal conditions such that the output is HIGH except when disabled by the control output Input and Measure Conditions A or LVTTL Pins B or GTLP Pins VinHIGH VCC 1.5 VinLOW 0.0 0.0 VM VCC/2 1.0 VX VOL + 0.3V N/A VY VOH + 0.3V N/A All input pulses have the following characteristics: Frequency = 10MHz, tRISE = tFALL = 2 ns, ZO = 50Ω. The outputs are measured one at a time with one transition per measurement. www.fairchildsemi.com 6 GTLP6C817 Low Drive GTLP/LVTTL 1:6 Clock Driver Physical Dimensions inches (millimeters) unless otherwise noted 24-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC24 Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 7 www.fairchildsemi.com