HLMP6405AGR

SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS HIGH EFF. RED YELLOW GREEN AIGaAs RED HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A Water Water Water Water Clear Clear Clear Clear MV6700A MV6300A MV6400A HLMP-Q150A Red Diffused Yellow Diffused Green Diffused Red Diffused FEATURES PACKAGE DIMENSIONS • Subminiature T-3/4 transfer molded • Low package profile .087 (2.2) .079 (2.0) • Axial leads .276 (7.0) MIN .024 (.6) .016 (.4) • Wide viewing angle .091 (2.3) .083 (2.1) .020 (.5) .012 (.3) .075 (1.9) DIA .063 (1.6) .010 (.26) .002 (.06) • SMT versions DESCRIPTION .058 (1.48) .050 (1.28) .056 (1.44) .048 (1.24) .031 (.78) .023 (.58) These T-3/4 subminiature LED lamps feature a square-base, transfer molded package for surface mount applications. A tinted diffused or water clear epoxy lens  available in AIGaAs red, high-efficiency red, green, and yellow  produces wide-angle beam emission and sharp on/off contrast. They are available with gullwing lead bends for top mounting, as well as yoke lead bends and Z-bends for mounting to the back of a PCB. CATHODE MARK (COLOR STRIPE ON SIDE OF PACKAGE) NOTES: ALL DIMENSIONS ARE IN INCHES (mm). ABSOLUTE MAXIMUM RATING (TA =25°C) HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A MV6700A MV6300A MV6400A HLMP-Q150A Power Dissipation 135 85 135 85 mW Average Forward Current 30 20 30 30 mA 90 60 90 300 mA 5 5 5 5 sec Operating Temperature -55 to +100 -55 to +100 -50 to +100 -20 to +100 °C Storage Temperature -55 to +100 -55 to +100 -50 to +100 -20 to +100 °C Parameter UNITS Peak Forward Current (1 µS pulsewidth, 0.1% DF) Lead Soldering Time at 260° C  2001 Fairchild Semiconductor Corporation DS300000 2/27/01 1 OF 5 www.fairchildsemi.com SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS ELECTRICAL / OPTICAL CHARACTERISTICS Part Number QTLP- MV6700A (TA =25°C) MV6300A MV6400A HLMP-Q150A Luminous Intensity (mcd) IF = 10mA Minimum 1.0 1.0 1.0 1.0* Typical 3.0 3.0 3.0 1.8* 3.0 3.0 3.0 1.8* Forward Voltage (V) Maximum Condition *Tested at I F = 1mA IF = 10mA 1.8 2.0 2.0 1.6* *Tested at I F = 1mA Peak Wavelength (nm) 635 585 565 660 IF = 10mA Spectral Line Half Width (nm) 40 36 28 20 IF = 10mA Reverse Voltage (V) 5 5 5 5 IR = 100µA Viewing Angle (°) 50 50 50 50 IF = 10mA Condition Typical ELECTRICAL / OPTICAL CHARACTERISTICS Part Number QTLP- (TA =25°C) HLMP-6305A HLMP-6405A HLMP-6505A HLMP-Q105A Minimum 3.0 3.0 3.0 20.0** Typical 12.0 12.0 12.0 50.0** Luminous Intensity (mcd) IF = 10mA Forward Voltage (V) **Tested at I F = 20mA IF = 10mA Maximum 3.0 3.0 3.0 2.4** Typical 1.8 2.0 2.0 1.8** **Tested at IF = 20mA Peak Wavelength (nm) 635 585 565 660 IF = 10mA Spectral Line Half Width (nm) 40 36 28 20 IF = 10mA Reverse voltage (V) 5 5 5 5 IR = 100µA Viewing Angle (°) 25 25 25 25 IF = 10mA www.fairchildsemi.com 2 OF 5 2/27/01 DS300000 SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS TYPICAL PERFORMANCE CURVES (TA =25°C) 2.5 90 IF - FORWARD CURRENT (mA) 80 RELATIVE LUMNOUS INTENSITY (NORMALIZED AT 10 mA) AlGaAs RED 70 HER 60 50 YELLOW 40 30 20 10 2.0 HER YELLOW GREEN 1.5 1.0 AlGaAs RED 0.5 GREEN 0.0 0 0 1.0 2.0 3.0 4.0 5 10 15 5.0 IF - DC FORWARD CURRENT (mA) VF - FORWARD VOLTAGE (V) Fig. 2 Relative Luminous Intensity vs. DC Forward Current Fig. 1 Forward Current vs. Forward Voltage 1.0 RELATIVE INTENSITY GREEN YELLOW AlGaAs RED 0.5 HER 0 500 550 600 650 700 750 WAVELENGTH (nm) Fig. 3 Relative Intensity vs. Peak Wavelength DS300000 2/27/01 3 OF 5 www.fairchildsemi.com SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS OPTIONAL CONFIGURATIONS GULLWING LEAD CONFIGURATION FEATURES • Available in Gullwing, Yoke and Z-bend lead formings • Compatible with automatic placement equipment • Compatible with vapor phase reflow soldering processes .087 (2.2) .079 (2.0) • Long life  solid state reliability ANODE CATHODE • Reel and tape or bulk packaging available .091 (2.3) .083 (2.1) DESCRIPTION .024 (.6) .016 (.4) .154 (3.90) .148 (3.75) .020 (.5) .012 (.3) These subminiature solid state lamps are transfer molded in an axial lead package. They are available in yellow, green, high efficiency red and AIGaAs red in both diffused and water clear lens. Automatic placement equipment can be used to mount the LEDs on the PC board. The lamps can be mounted using either batch or in line vapor phase reflow solder processes. .078 (1.9) .063 (1.6) .115 (2.92) .099 (2.52) .058 (1.48) .050 (1.28) .010 (.26) .002 (.06) .033 (.82) .000 (.00) .016 (.4) .008 (.2) .039 (1.0) .028 (.7) NOTES: ALL DIMENSIONS ARE IN INCHES (mm) Z-BEND LEAD CONFIGURATION YOKE LEAD CONFIGURATION .087 (2.2) .079 (2.0) .020 (.5) .012 (.3) .087 (2.2) .079 (2.0) ANODE CATHODE .091 (2.3) .083 (2.1) .091 (2.3) .083 (2.1) .024 (.6) .016 (.4) .024 (.6) .016 (.4) CATHODE .300 (7.62) MAX .240 (6.1) .232 (5.9) ANODE .128 (3.24) .112 (2.84) .078 (1.9) .063 (1.6) .115 (2.92) .099 (2.52) .058 (1.48) .050 (1.28) .117 (2.96) .100 (2.56) www.fairchildsemi.com .020 (.5) .012 (.3) .047 (1.2) .031 (0.8) .010 (.26) .002 (.06) .039 (.99) .023 (.59) .078 (1.9) .063 (1.6) .033 (.85) .026 (.65) .010 (.26) .002 (.06) .058 (1.48) .050 (1.28) .033 (.85) .026 (.66) .048 (1.22) .032 (.82) 4 OF 5 .189 (4.8) .173 (4.4) .034 (.86) .026 (.66) 2/27/01 DS300000 SUBMINIATURE T-3/4 LED DIFFUSED and CLEAR LAMPS DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body,or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in labeling, can be reasonably expected to result in a significant injury of the user. DS300000 2/27/01 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 5 OF 5 www.fairchildsemi.com