KA2807DTF

KA2807 Ground Fault Circuit Interrupter Description The KA2807 is an IC for ground fault circuit interrupters which are intended to provide an electrical shock hazard protection from line to ground fault currents on grounded circuits of 120 V supplies. www.onsemi.com Features • • • • • • • • • • RELATED STANDARDS Full Advantage of the UL943 Built−In Voltage Regulator Sense Coil Ratio – 1000:1 GND/Neutral Coil Ratio – 200:1 Trip Time in Normal Fault and Grounded Neutral Fault is 18 ms Typ Wide Operating Temperature Range Excellent ESD Characteristic 1 mA Output Current Pulse to Trigger SCR Available in 8 Pin SOIC and 8 Pin MSOP Pb−Free Device UL943 SOIC8 CASE 751EB Micro8 CASE 846A MARKING DIAGRAMS 8 8 ON AYWZZ KA2807 KA2807 AYWG G 1 1 SOIC8 Micro8 KA2807 = Specific Device Code A = Assembly Location Y = Year W = Work Week ZZ = Assembly LOT Code G = Pb−Free Package (Note: Microdot may be in either location) ORDERING INFORMATION Device Package Shipping† KA2807DTF SOIC (Pb−Free) 2,500 / Tape & Reel KA2807MUX Micro8 (Pb−Free) 4,000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2002 July, 2019 − Rev. 2 1 Publication Order Number: KA2807/D KA2807 PIN ASSIGNMENT Trigger Out 1 8 VCC − Input 2 7 Timing Capacitor + Input 3 6 Timing Resistor GND 4 5 Amp Out Figure 1. Pin Out KA2807 in 8−pin SOP or MSOP (Top View) BLOCK DIAGRAM VCC AMP OUT TIMING RESISTOR 8 5 6 V. REG. +INPUT 3 TIMING CONTROL + AMP −INPUT 7 − 2 LATCH 4 1 GND TRIGGER OUT Figure 2. KA2807 Block Diagram www.onsemi.com 2 TIMING CAPACITOR KA2807 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Min Max Unit mA ICC Supply Current − +19 PD Power Dissipation SOIC−8 MSOP−8 − − 0.41 0.3 W TOPR Operating Temperature Range −40 +70 °C TSTG Storage Temperature Range −55 +150 °C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. ELECTRICAL CHARACTERISTICS Symbol Parameter Conditions Min Typ Max Unit VREG Shunt Regulator Voltage Pin 8, S1: 2, S2: OFF 23 26 29 V VREF Amplifier Reference Voltage Pin 3, S1: 2, S2: OFF 9.5 10.5 11.5 V VOH Amplifier High Output Voltage Pin 5, S1: 3, S2: ON Sig: 800 Hz, 3.0 VP−P Sinusoidal wave 17 19 21 V VOL Amplifier Low Output Voltage Pin 5, S1: 3, S2: ON Sig: 800 Hz, 3.0 VP−P Sinusoidal wave 1.5 2.5 3.5 V ISEN Amplifier Sensitivity Current Pin 2, S1: 3, S2: ON Sig: 800 Hz, 1.0 VP−P ~ 2.5 VP−P Sinusoidal wave 3.5 5 6.5 mArms Latch On Voltage Pin 7, S1: 3, S2: ON Sig: 800 Hz, 3.0 VP−P Sinusoidal wave 16.5 17.5 19.5 V ITR SCR Trigger Current Pin 1, S1: 3, S2: ON Sig: 800 Hz, 3.0 VP−P Sinusoidal wave 0.5 1 2.0 mA VS 1 Output Low Voltage Pin 1, S1: 2, S2: OFF − 100 240 mA ZO Output Impedance Pin 1, S1: 2, S2: OFF − 100 250 W Output Sink Current Pin 1, S1: 2, S2: OFF 2.0 6.0 − mA VON(LATCH) ISINK Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 3 KA2807 TEST CIRCUIT VCC = 31 V ICC = 5 mA 1 kW 1.45 MW 0.002 mF 8 7 6 5 3 4 KA2807 1 2 S1 A3 1 A1 0.3 V 2 3 A2 1 kW 100 kW S2 0.047 mF SIG Figure 3. KA2807 Test Circuit www.onsemi.com 4 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC8 CASE 751EB ISSUE A DOCUMENT NUMBER: DESCRIPTION: 98AON13735G SOIC8 DATE 24 AUG 2017 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS Micro8 CASE 846A−02 ISSUE K DATE 16 JUL 2020 SCALE 2:1 GENERIC MARKING DIAGRAM* 8 XXXX AYWG G 1 XXXX A Y W G = Specific Device Code = Assembly Location = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “G”, may or may not be present. Some products may not follow the Generic Marking. DOCUMENT NUMBER: DESCRIPTION: 98ASB14087C MICRO8 STYLE 1: PIN 1. 2. 3. 4. 5. 6. 7. 8. SOURCE SOURCE SOURCE GATE DRAIN DRAIN DRAIN DRAIN STYLE 2: PIN 1. 2. 3. 4. 5. 6. 7. 8. SOURCE 1 GATE 1 SOURCE 2 GATE 2 DRAIN 2 DRAIN 2 DRAIN 1 DRAIN 1 STYLE 3: PIN 1. 2. 3. 4. 5. 6. 7. 8. N-SOURCE N-GATE P-SOURCE P-GATE P-DRAIN P-DRAIN N-DRAIN N-DRAIN Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative