KAI-01150-QBA-FD-AE

KAI-01150 1280 (H) x 720 (V) Interline CCD Image Sensor Description The ON Semiconductor KAI−01150 Image Sensor is a 720p format (1280 x 720 pixel) CCD in a 1/2” optical format. Based on the TRUESENSE 5.5 micron Interline Transfer CCD Platform, the sensor features broad dynamic range, excellent imaging performance, and a flexible readout architecture that enables use of 1, 2, or 4 outputs for full resolution readout of 138 frames per second. A vertical overflow drain structure suppresses image blooming and enables electronic shuttering for precise exposure control. www.onsemi.com Table 1. GENERAL SPECIFICATIONS Parameter Typical Value Architecture Interline CCD, Progressive Scan Total Number of Pixels 1364 (H) × 760 (V) Number of Effective Pixels 1320 (H) × 736 (V) Number of Active Pixels 1280 (H) × 720 (V) Pixel Size 5.5 mm (H) × 5.5 mm (V) Active Image Size 7.04 mm (H) × 3.96 mm (V) 8.08 mm (diag.), 1/2″ Optical Format Aspect Ratio 16:9 Number of Outputs 1, 2, or 4 Charge Capacity 20,000 electrons Output Sensitivity 34 mV/e− Quantum Efficiency Pan (−ABA, −QBA, −PBA) R, G, B (−FBA, −QBA) R, G, B (−CBA, −PBA) 44% 31%, 37%, 38% 29%, 37%, 39% Base ISO KAI−01150−ABA KAI−01150−FBA KAI−01150−CBA KAI−01150−PBA 330 170 150 330 Read Noise (f = 40 MHz) 12 e− rms Dark Current Photodiode / VCCD 7 / 140 e−/s Dark Current Doubling Temp Photodiode / VCCD 7°C / 9°C Dynamic Range 64 dB Charge Transfer Efficiency 0.999999 Blooming Suppression > 300 X Smear −100 dB Image Lag < 10 electrons Maximum Pixel Clock Speed 40 MHz Maximum Frame Rate Quad / Dual / Single Output 138 / 69 / 36 fps Figure 1. KAI−01150 Interline CCD Image Sensor Features • Bayer Color Pattern, TRUESENSE Sparse • • • • • • • Color Filter Pattern, and Monochrome Configurations Progressive Scan Readout Flexible Readout Architecture High Frame Rate High Sensitivity Low Noise Architecture Excellent Smear Performance Package Pin Reserved for Device Identification Applications Package Options 68 Pin PGA 64 Pin CLCC Cover Glass AR Coated, 2-Sides or Clear Glass • Intelligent Traffic Systems • Security / Surveillance • Industrial Imaging ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. NOTE: All Parameters are specified at T = 40°C unless otherwise noted. © Semiconductor Components Industries, LLC, 2015 August, 2015 − Rev. 5 1 Publication Order Number: KAI−01150/D KAI−01150 The sensor is available with the TRUESENSE Sparse Color Filter Pattern, a technology which provides a 2x improvement in light sensitivity compared to a standard color Bayer part. The sensor shares common PGA pin−out and electrical configurations with other devices based on the TRUESENSE 5.5 micron Interline Transfer CCD Platform, allowing a single camera design to support multiple members of this sensor family. ORDERING INFORMATION Standard Devices See full datasheet for ordering information associated with devices no longer recommended for new designs. Table 2. ORDERING INFORMATION − STANDARD DEVICES Part Number Description KAI−01150−ABA−JD−BA Monochrome, Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−ABA−JD−AE Monochrome, Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−ABA−FD−BA Monochrome, Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−ABA−FD−AE Monochrome, Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−FBA−JD−BA Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−FBA−JD−AE Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−FBA−FD−BA Gen2 Color (Bayer RGB), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−FBA−FD−AE Gen2 Color (Bayer RGB), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−FBA−JB−B2 Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass (no coatings), Grade 2 KAI−01150−FBA−JB−AE Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass (no coatings), Engineering Grade KAI−01150−QBA−JD−BA Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−QBA−JD−AE Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−QBA−FD−BA Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−QBA−FD−AE Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade Marking Code KAI−01150−ABA Serial Number KAI−01150−FBA Serial Number KAI−01150−QBA Serial Number See the ON Semiconductor Device Nomenclature document (TND310/D) for a full description of the naming convention used for image sensors. For reference documentation, including information on evaluation kits, please visit our web site at www.onsemi.com. www.onsemi.com 2 KAI−01150 Not Recommended for New Designs Table 3. ORDERING INFORMATION − NOT RECOMMENDED FOR NEW DESIGNS Part Number Description KAI−01150−CBA−JD−BA Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−CBA−JD−AE Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−CBA−FD−BA Gen1 Color (Bayer RGB), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−CBA−FD−AE Gen1 Color (Bayer RGB), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−CBA−JB−B2 Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass (no coatings), Grade 2 KAI−01150−CBA−JB−AE Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass (no coatings), Engineering Grade KAI−01150−PBA−JD−BA Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−PBA−JD−AE Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI−01150−PBA−FD−BA Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI−01150−PBA−FD−AE Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, CLCC Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade www.onsemi.com 3 Marking Code KAI−01150−CBA Serial Number KAI−01150−PBA Serial Number KAI−01150 DEVICE DESCRIPTION Architecture H2Bd H2Sd H1Bd H1Sd SUB H2Bc H2Sc H1Bc H1Sc RDc Rc VDDc VOUTc RDd Rd VDDd VOUTd ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ 1 10 22 20 640 640 20 22 10 1 1 Dummy 12 GND OGc H2SLc GND OGd H2SLd 8 V1T V2T V3T V4T V1T V2T V3T V4T DevID ESD 22 1280 (H) × 720 (V) 5.5 mm × 5.5 mm Pixels 20 20 22 V1B V2B V3B V4B RDa Ra VDDa VOUTa ESD V1B V2B V3B V4B ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ 8 Buffer 12 Dark 1 Dummy 1 10 22 20 640 640 H2Bb H2Sb H1Bb H1Sb SUB H2Ba H2Sa H1Ba H1Sa GND OGa H2SLa (Last VCCD Phase = V1 → H1S) 20 22 10 1 RDb Rb VDDb VOUTb GND OGb H2SLb Figure 2. Block Diagram Dark Reference Pixels These pixels are light sensitive but are not tested for defects and non-uniformities. There are 12 dark reference rows at the top and 12 dark rows at the bottom of the image sensor. The dark rows are not entirely dark and so should not be used for a dark reference level. Use the 22 dark columns on the left or right side of the image sensor as a dark reference. Under normal circumstances use only the center 20 columns of the 22 column dark reference due to potential light leakage. Image Acquisition An electronic representation of an image is formed when incident photons falling on the sensor plane create electron-hole pairs within the individual silicon photodiodes. These photoelectrons are collected locally by the formation of potential wells at each photosite. Below photodiode saturation, the number of photoelectrons collected at each pixel is linearly dependent upon light level and exposure time and non-linearly dependent on wavelength. When the photodiodes charge capacity is reached, excess electrons are discharged into the substrate to prevent blooming. Dummy Pixels Within each horizontal shift register there are 11 leading additional shift phases. These pixels are designated as dummy pixels and should not be used to determine a dark reference level. In addition, there is one dummy row of pixels at the top and bottom of the image. ESD Protection Adherence to the power-up and power-down sequence is critical. Failure to follow the proper power-up and power-down sequences may cause damage to the sensor. See Power-Up and Power-Down Sequence section. Active Buffer Pixels 20 unshielded pixels adjacent to any leading or trailing dark reference regions are classified as active buffer pixels. www.onsemi.com 4 KAI−01150 Bayer Color Filter Pattern H2Bd H2Sd H1Bd H1Sd SUB H2Bc H2Sc H1Bc H1Sc RDc Rc VDDc VOUTc RDd Rd VDDd VOUTd ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ 1 10 22 20 640 640 20 22 10 1 1 Dummy 12 GND OGc H2SLc GND OGd H2SLd 8 B G G R V1T V2T V3T V4T B G G R V1T V2T V3T V4T DevID ESD V1B V2B V3B V4B 22 1280 (H) × 720 (V) 5.5 mm × 5.5 mm Pixels 20 20 22 B G G R ESD B G G R ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ V1B V2B V3B V4B 8 Buffer RDa Ra VDDa VOUTa RDb Rb VDDb VOUTb 12 Dark 1 Dummy (Last VCCD Phase = V1 → H1S) 1 10 22 20 640 20 22 10 1 GND OGb H2SLb H2Bb H2Sb H1Bb H1Sb SUB H2Ba H2Sa H1Ba H1Sa GND OGa H2SLa 640 Figure 3. Bayer Color Filter Pattern TRUESENSE Sparse Color Filter Pattern H2Bd H2Sd H1Bd H1Sd SUB H2Bc H2Sc H1Bc H1Sc RDc Rc VDDc VOUTc RDd Rd VDDd VOUTd ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ 1 10 22 20 640 640 20 22 10 1 1 Dummy 12 GND OGc H2SLc GND OGd H2SLd 8 G P B P V1T V2T V3T V4T P G P B R P G P G P B P P R P G P G P B R P G P P R P G V1T V2T V3T V4T DevID ESD 22 V1B V2B V3B V4B RDa Ra VDDa VOUTa G P B P P G P B R P G P 20 22 G P B P P R P G P G P B R P G P ESD V1B V2B V3B V4B P R P G ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ 8 Buffer 12 Dark 1 Dummy (Last VCCD Phase = V1 → H1S) 1 10 22 20 640 640 H2Bb H2Sb H1Bb H1Sb SUB H2Ba H2Sa H1Ba H1Sa GND OGa H2SLa 1280 (H) × 720 (V) 5.5 mm × 5.5 mm Pixels 20 Figure 4. TRUESENSE Sparse Color Filter Pattern www.onsemi.com 5 20 22 10 1 RDb Rb VDDb VOUTb GND OGb H2SLb KAI−01150 Physical Description PGA Pin Description and Device Orientation 67 65 63 61 59 57 55 53 51 49 47 V3T V1T VDDc GND Rc H2SLc H1Bc H2Sc N/C H2Sd H1Bd 68 66 64 62 60 58 56 54 52 50 48 ESD V4T V2T VOUTc RDc OGc H2Bc H1Sc SUB H1Sd H2Bd 45 H2SLd 43 41 39 37 35 Rd GND VDDd V1T V3T 46 44 42 40 38 36 OGd RDd VOUTd V2T V4T DevID Pixel (1, 1) 4 6 V4B V2B 8 VOUTa 10 12 14 16 18 20 22 24 26 28 30 32 34 RDa OGa H2Ba H1Sa SUB H1Sb H2Bb OGb RDb VOUTb V2B V4B ESD 23 25 27 29 31 33 H2SLb Rb GND VDDb V1B V3B 1 3 5 7 9 11 13 15 17 19 V3B V1B VDDa GND Ra H2SLa H1Ba H2Sa N/C H2Sb 21 H1Bb Figure 5. PGA Package Pin Designations − Top View Table 4. PGA PACKAGE PIN DESCRIPTION Pin Name 1 V3B Vertical CCD Clock, Phase 3, Bottom Description 3 V1B Vertical CCD Clock, Phase 1, Bottom 4 V4B Vertical CCD Clock, Phase 4, Bottom 5 VDDa Output Amplifier Supply, Quadrant a 6 V2B Vertical CCD Clock, Phase 2, Bottom 7 GND Ground 8 VOUTa 9 Ra Reset Gate, Quadrant a 10 RDa Reset Drain, Quadrant a 11 H2SLa Video Output, Quadrant a Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant a 12 OGa Output Gate, Quadrant a 13 H1Ba Horizontal CCD Clock, Phase 1, Barrier, Quadrant a 14 H2Ba Horizontal CCD Clock, Phase 2, Barrier, Quadrant a 15 H2Sa Horizontal CCD Clock, Phase 2, Storage, Quadrant a 16 H1Sa Horizontal CCD Clock, Phase 1, Storage, Quadrant a 17 N/C No Connect 18 SUB Substrate 19 H2Sb Horizontal CCD Clock, Phase 2, Storage, Quadrant b 20 H1Sb Horizontal CCD Clock, Phase 1, Storage, Quadrant b 21 H1Bb Horizontal CCD Clock, Phase 1, Barrier, Quadrant b 22 H2Bb Horizontal CCD Clock, Phase 2, Barrier, Quadrant b 23 H2SLb Horizontal CCD Clock, Phase 1, Storage, Last Phase, Quadrant b 24 OGb Output Gate, Quadrant b www.onsemi.com 6 KAI−01150 Table 4. PGA PACKAGE PIN DESCRIPTION (continued) Pin Name Description 25 Rb Reset Gate, Quadrant b 26 RDb Reset Drain, Quadrant b 27 GND Ground 28 VOUTb 29 VDDb Output Amplifier Supply, Quadrant b 30 V2B Vertical CCD Clock, Phase 2, Bottom 31 V1B Vertical CCD Clock, Phase 1, Bottom 32 V4B Vertical CCD Clock, Phase 4, Bottom 33 V3B Vertical CCD Clock, Phase 3, Bottom 34 ESD ESD Protection Disable 35 V3T Vertical CCD Clock, Phase 3, Top 36 DevID 37 V1T Vertical CCD Clock, Phase 1, Top 38 V4T Vertical CCD Clock, Phase 4, Top 39 VDDd 40 V2T Vertical CCD Clock, Phase 2, Top 41 GND Ground 42 VOUTd 43 Rd Reset Gate, Quadrant d 44 RDd Reset Drain, Quadrant d 45 H2SLd Video Output, Quadrant b Device Identification Output Amplifier Supply, Quadrant d Video Output, Quadrant d Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant d 46 OGd Output Gate, Quadrant d 47 H1Bd Horizontal CCD Clock, Phase 1, Barrier, Quadrant d 48 H2Bd Horizontal CCD Clock, Phase 2, Barrier, Quadrant d 49 H2Sd Horizontal CCD Clock, Phase 2, Storage, Quadrant d 50 H1Sd Horizontal CCD Clock, Phase 1, Storage, Quadrant d 51 N/C No Connect 52 SUB Substrate 53 H2Sc Horizontal CCD Clock, Phase 2, Storage, Quadrant c 54 H1Sc Horizontal CCD Clock, Phase 1, Storage, Quadrant c 55 H1Bc Horizontal CCD Clock, Phase 1, Barrier, Quadrant c 56 H2Bc Horizontal CCD Clock, Phase 2, Barrier, Quadrant c 57 H2SLc Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant c 58 OGc Output Gate, Quadrant c 59 Rc Reset Gate, Quadrant c 60 RDc Reset Drain, Quadrant c 61 GND Ground 62 VOUTc Video Output, Quadrant c 63 VDDc Output Amplifier Supply, Quadrant c 64 V2T Vertical CCD Clock, Phase 2, Top 65 V1T Vertical CCD Clock, Phase 1, Top 66 V4T Vertical CCD Clock, Phase 4, Top 67 V3T Vertical CCD Clock, Phase 3, Top 68 ESD EDS Protection Disable 1. Liked named pins are internally connected and should have a common drive signal. 2. N/C pins (17, 51) should be left floating. www.onsemi.com 7 KAI−01150 RDd Rd 38 37 36 35 34 OGd H1Bd H2SLd H1Sd H2Bd H2Sd 39 SUB 42 41 40 H2Sc H1Sc H1Bc H2SLc H2Bc OGc Rc Ceramic Leadless Chip Carrier Pin Description RDc 48 47 46 45 44 43 49 33 32 GND 50 31 VOUTd VOUTc 51 30 VDDd VDDc 52 29 V2T V2T 53 28 V1T V1T 54 27 V4T V4T 55 26 V3T GND V3T 56 25 DevID ESD 57 24 V3B V3B 58 23 V4B V4B 59 22 V1B V1B 60 21 V2B V2B 61 20 VDDb 62 19 VOUTb 63 18 GND 64 1 17 RDb 8 9 10 11 12 13 14 15 16 H1Ba H1Sa H2Sa SUB H2Sb H1Sb Rb 7 OGb 6 H2Bb 5 H2SLb 4 H1Bb 3 H2Ba 2 OGa RDa GND H2SLa VOUTa Ra VDDa Pixel (1, 1) Figure 6. CLCC Package Pin Designations − Top View Table 5. CLCC PACKAGE PIN DESCRIPTION Pin Name 1 RDa Reset Drain, Quadrant a 2 Ra Reset Gate, Quadrant a 3 OGa Output Gate, Quadrant a 4 H2SLa Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant a 5 H2Ba Horizontal CCD Clock, Phase 2, Barrier, Quadrant a 6 H1Ba Horizontal CCD Clock, Phase 1, Barrier, Quadrant a 7 H1Sa Horizontal CCD Clock, Phase 1, Storage, Quadrant a 8 H2Sa Horizontal CCD Clock, Phase 2, Storage, Quadrant a Description 9 SUB Substrate 10 H2Sb Horizontal CCD Clock, Phase 2, Storage, Quadrant b 11 H1Sb Horizontal CCD Clock, Phase 1, Storage, Quadrant b 12 H1Bb Horizontal CCD Clock, Phase 1, Barrier, Quadrant b 13 H2Bb Horizontal CCD Clock, Phase 2, Barrier, Quadrant b 14 H2SLb Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant b 15 OGb Output Gate, Quadrant b 16 Rb Reset Gate, Quadrant b 17 RDb Reset Drain, Quadrant b 18 GND Ground 19 VOUTb Video Output, Quadrant b www.onsemi.com 8 KAI−01150 Table 5. CLCC PACKAGE PIN DESCRIPTION (continued) Pin Name Description 20 VDDb Output Amplifier Supply, Quadrant b 21 V2B Vertical CCD Clock, Phase 2, Bottom 22 V1B Vertical CCD Clock, Phase 1, Bottom 23 V4B Vertical CCD Clock, Phase 4, Bottom 24 V3B Vertical CCD Clock, Phase 3, Bottom 25 DevID 26 V3T Vertical CCD Clock, Phase 3, Top 27 V4T Vertical CCD Clock, Phase 4, Top 28 V1T Vertical CCD Clock, Phase 1, Top 29 V2T Vertical CCD Clock, Phase 2, Top Device Identification 30 VDDd 31 VOUTd Output Amplifier Supply, Quadrant d 32 GND Ground 33 RDd Reset Drain, Quadrant d 34 Rd Reset Gate, Quadrant d 35 OGd Output Gate, Quadrant d 36 H2SLd Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant d 37 H2Bd Horizontal CCD Clock, Phase 2, Barrier, Quadrant d 38 H1Bd Horizontal CCD Clock, Phase 1, Barrier, Quadrant d 39 H1Sd Horizontal CCD Clock, Phase 1, Storage, Quadrant d 40 H2Sd Horizontal CCD Clock, Phase 2, Storage, Quadrant d 41 SUB Substrate 42 H2Sc Horizontal CCD Clock, Phase 2, Storage, Quadrant c 43 H1Sc Horizontal CCD Clock, Phase 1, Storage, Quadrant c 44 H1Bc Horizontal CCD Clock, Phase 1, Barrier, Quadrant c 45 H2Bc Horizontal CCD Clock, Phase 2, Barrier, Quadrant c 46 H2SLc Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant c 47 OGc Output Gate, Quadrant c 48 Rc Reset Gate, Quadrant c 49 RDc Reset Drain, Quadrant c 50 GND Ground 51 VOUTc Video Output, Quadrant c 52 VDDc Output Amplifier Supply, Quadrant c 53 V2T Vertical CCD Clock, Phase 2, Top 54 V1T Vertical CCD Clock, Phase 1, Top 55 V4T Vertical CCD Clock, Phase 4, Top 56 V3T Vertical CCD Clock, Phase 3, Top 57 ESD ESD Protection Disable 58 V3B Vertical CCD Clock, Phase 3, Bottom 59 V4B Vertical CCD Clock, Phase 4, Bottom 60 V1B Vertical CCD Clock, Phase 1, Bottom 61 V2B Vertical CCD Clock, Phase 2, Bottom 62 VDDa Output Amplifier Supply, Quadrant a 63 VOUTa Video Output, Quadrant a 64 GND Video Output, Quadrant d Ground 1. Liked named pins are internally connected and should have a common drive signal. www.onsemi.com 9 KAI−01150 IMAGING PERFORMANCE Table 6. TYPICAL OPERATION CONDITIONS Unless otherwise noted, the Imaging Performance Specifications are measured using the following conditions. Condition Notes Light Source Continuous red, green and blue LED illumination For monochrome sensor, only green LED used. Operation Nominal operating voltages and timing Description Table 7. SPECIFICATIONS Description Dark Field Global Non−Uniformity Symbol Min. Nom. Max. Units DSNU − − 2.0 mVpp Die 27, 40 − 2.0 5.0 %rms Die 27, 40 1 − 5.0 15.0 %pp Die 27, 40 1 27, 40 1 Bright Field Global Non−Uniformity Bright Field Global Peak to Peak Non−Uniformity Temperature Tested At (5C) Sampling Plan PRNU Bright Field Center Non−Uniformity Notes − 1.0 2.0 %rms Die Maximum Photoresponse Nonlinearity NL − 2 − % Design 2 Maximum Gain Difference Between Outputs DG − 10 − % Design 2 Maximum Signal Error due to Nonlinearity Differences DNL − 1 − % Design 2 Horizontal CCD Charge Capacity HNe − 55 − ke− Design Vertical CCD Charge Capacity VNe − 45 − ke− Design ke− Die Photodiode Charge Capacity PNe − 20 − Horizontal CCD Charge Transfer Efficiency HCTE 0.999995 0.999999 − Die Vertical CCD Charge Transfer Efficiency VCTE 0.999995 0.999999 − Die Photodiode Dark Current Ipd − 7 70 e/p/s Die 40 Vertical CCD Dark Current Ivd − 140 400 e/p/s Die 40 − 10 e− Design Image Lag Lag − Antiblooming Factor Xab 300 − − Vertical Smear Smr − −100 − dB Design 12 − e−rms Design Read Noise 27, 40 3 Design ne−T − Dynamic Range DR − 64 − dB Design Output Amplifier DC Offset Vodc − 9.4 − V Die Output Amplifier Bandwidth f−3db − 250 − MHz Die Output Amplifier Impedance ROUT − 127 − W Die Output Amplifier Sensitivity DV/DN − 34 − mV/e− Design 4 4, 5 27, 40 6 27, 40 1. Per color 2. Value is over the range of 10% to 90% of photodiode saturation. 3. The operating value of the substrate voltage, VAB, will be marked on the shipping container for each device. The value of VAB is set such that the photodiode charge capacity is 680 mV. 4. At 40 MHz 5. Uses 20LOG (PNe/ ne−T) 6. Assumes 5 pF load. www.onsemi.com 10 KAI−01150 Table 8. KAI−01150−ABA AND KAI−01150−PBA CONFIGURATIONS Symbol Min. Nom. Max. Units Sampling Plan Peak Quantum Efficiency QEmax − 44 − % Design Peak Quantum Efficiency Wavelength lQE − 480 − nm Design Description Temperature Tested At (5C) Notes Table 9. KAI−01150−FBA AND KAI−01150−QBA GEN2 COLOR CONFIGURATIONS WITH MAR GLASS Description Symbol Min. Nom. Max. Units Sampling Plan Peak Quantum Efficiency Blue Green Red QEmax − 38 37 31 − % Design Peak Quantum Efficiency Wavelength Blue Green Red lQE − 460 530 605 − nm Design Temperature Tested At (5C) Notes Table 10. KAI−01150−CBA AND KAI−01150−PBA GEN1 COLOR CONFIGURATIONS WITH MAR GLASS Description Symbol Min. Nom. Max. Units Sampling Plan Temperature Tested At (5C) Notes Peak Quantum Efficiency Blue Green Red QEmax − 39 37 29 − % Design 1 Peak Quantum Efficiency Wavelength Blue Green Red lQE − 470 540 620 − nm Design 1 1. This color filter set configuration (Gen1) is not recommended for new designs. Table 11. KAI−01150−FBA GEN2 COLOR CONFIGURATIONS WITH CLEAR GLASS Description Symbol Min. Nom. Max. Units Sampling Plan Peak Quantum Efficiency Blue Green Red QEmax − 35 34 29 − % Design Peak Quantum Efficiency Wavelength Blue Green Red lQE − 460 530 605 − nm Design Temperature Tested At (5C) Notes Temperature Tested At (5C) Notes Table 12. KAI−01150−CBA GEN1 COLOR CONFIGURATIONS WITH CLEAR GLASS Description Symbol Min. Nom. Max. Units Sampling Plan Peak Quantum Efficiency Blue Green Red QEmax − 36 34 27 − % Design 1 Peak Quantum Efficiency Wavelength Blue Green Red lQE − 470 540 620 − nm Design 1 1. This color filter set configuration (Gen1) is not recommended for new designs. www.onsemi.com 11 KAI−01150 TYPICAL PERFORMANCE CURVES Quantum Efficiency Monochrome with Microlens NOTE: The PGA and CLCC versions have different quantum efficiencies due to differences in the cover glass transmission. See Figure 34: Cover Glass Transmission for more details. Figure 7. Monochrome with Microlens Quantum Efficiency Color (Bayer RGB) with Microlens and MAR Cover Glass (Gen2 and Gen1 CFA) Figure 8. MAR Glass Color (Bayer) with Microlens Quantum Efficiency www.onsemi.com 12 KAI−01150 Color (Bayer RGB) with Microlens and Clear Cover Glass (Gen2 and Gen1 CFA) Figure 9. Clear Glass Color (Bayer) with Microlens Quantum Efficiency Color (TRUESENSE Sparse CFA) with Microlens (Gen2 and Gen1 CFA) Figure 10. Color (TRUESENSE Sparse CFA) with Microlens Quantum Efficiency www.onsemi.com 13 KAI−01150 Angular Quantum Efficiency For the curves marked “Horizontal”, the incident light angle is varied in a plane parallel to the HCCD. For the curves marked “Vertical”, the incident light angle is varied in a plane parallel to the VCCD. Monochrome with Microlens 100 Relative Quantum Efficiency (%) 90 Vertical 80 70 60 50 Horizontal 40 30 20 10 0 −30 −20 −10 0 10 20 30 Angle (degrees) Figure 11. Monochrome with Microlens Angular Quantum Efficiency Dark Current vs. Temperature 10000 Dark Current (e/s) 1000 VCCD 100 10 Photodiode 1 0.1 1000/T (K) 2.9 3.0 3.1 3.2 3.3 3.4 T (°C) 72 60 50 40 30 21 Figure 12. Dark Current vs. Temperature www.onsemi.com 14 KAI−01150 Power-Estimated 0.6 0.5 Power (W) 0.4 0.3 0.2 0.1 0.0 10 15 20 25 30 35 40 HCCD Frequency (MHz) Single Dual Quad Figure 13. Power Frame Rate (fps) Frame Rates 200 200 180 180 160 160 140 140 120 120 100 100 80 80 60 60 40 40 20 20 0 0 10 15 20 25 30 35 HCCD Frequency (MHz) Single Dual (Left/Right) Figure 14. Frame Rates www.onsemi.com 15 Quad 40 KAI−01150 DEFECT DEFINITIONS Table 13. OPERATION CONDITIONS FOR DEFECT TESTING AT 405C Description Operational Mode Condition Notes Two Outputs, Using VOUTa and VOUTc, Continuous Readout HCCD Clock Frequency 10 MHz Pixels per Line 1520 1 Lines per Frame 480 2 Line Time 154.9 ms Frame Time 74.4 ms Photodiode Integration Time Mode A: PD_Tint = Frame Time = 74.4 ms, No Electronic Shutter Used Mode B: PD_Tint = 33 ms, Electronic Shutter Used VCCD Integration Time 58.9 ms 3 Temperature 40°C Light Source Continuous Red, Green and Blue LED Illumination Operation 1. 2. 3. 4. 4 Nominal Operating Voltages and Timing Horizontal overclocking used. Vertical overclocking used. VCCD Integration Time = 380 lines × Line Time, which is the total time a pixel will spend in the VCCD registers. For monochrome sensor, only the green LED is used. Table 14. DEFECT DEFINITIONS FOR TESTING AT 405C Description Definition Standard Grade Grade 2 Notes Major Dark Field Defective Bright Pixel PD_Tint = Mode A → Defect ≥ 25 mV or PD_Tint = Mode B → Defect ≥ 12 mV 10 10 1 Major Bright Field Defective Dark Pixel Defect ≥ 12% 10 10 1 Minor Dark Field Defective Bright Pixel PD_Tint = Mode A → Defect ≥ 13 mV or PD_Tint = Mode B → Defect ≥ 6 mV 100 100 Cluster Defect (Standard Grade) A group of 2 to 10 contiguous major defective pixels, but no more than 2 adjacent defects horizontally. 0 N/A 2 Cluster Defect (Grade 2) A group of 2 to 10 contiguous major defective pixels. N/A 5 2 Column Defect A group of more than 10 contiguous major defective pixels along a single column. 0 0 2 1. For the color device (KAI−01150−CBA or KAI−01150−PBA), a bright field defective pixel deviates by 12% with respect to pixels of the same color. 2. Column and cluster defects are separated by no less than two (2) good pixels in any direction (excluding single pixel defects). www.onsemi.com 16 KAI−01150 Table 15. OPERATION CONDITIONS FOR DEFECT TESTING AT 275C Description Operational Mode Condition Notes Two Outputs, Using VOUTa and VOUTc, Continuous Readout HCCD Clock Frequency 20 MHz Pixels per Line 1520 1 Lines per Frame 480 2 Line Time 77.8 ms Frame Time 37.3 ms Photodiode Integration Time (PD_Tint) Mode A: PD_Tint = Frame Time = 37.3 ms, No Electronic Shutter Used Mode B: PD_Tint = 33 ms, Electronic Shutter Used VCCD Integration Time 29.5 ms 3 Temperature 27°C Light Source Continuous Red, Green and Blue LED Illumination Operation 1. 2. 3. 4. 4 Nominal Operating Voltages and Timing Horizontal overclocking used. Vertical overclocking used. VCCD Integration Time = 380 lines × Line Time, which is the total time a pixel will spend in the VCCD registers. For monochrome sensor, only the green LED is used. Table 16. DEFECT DEFINITIONS FOR TESTING AT 275C Description Definition Standard Grade Grade 2 Notes Major Dark Field Defective Bright Pixel PD_Tint = Mode A → Defect ≥ 8 mV or PD_Tint = Mode B → Defect ≥ 4 mV 10 10 1 Major Bright Field Defective Dark Pixel Defect ≥ 12% 10 10 1 Cluster Defect (Standard Grade) A group of 2 to 10 contiguous major defective pixels, but no more than 2 adjacent defects horizontally. 0 N/A 2 Cluster Defect (Grade 2) A group of 2 to 10 contiguous major defective pixels. N/A 5 2 Column Defect A group of more than 10 contiguous major defective pixels along a single column. 0 0 2 1. For the color device (KAI−01150−CBA or KAI−01150−PBA), a bright field defective pixel deviates by 12% with respect to pixels of the same color. 2. Column and cluster defects are separated by no less than two (2) good pixels in any direction (excluding single pixel defects). Defect Map The defect map supplied with each sensor is based upon testing at an ambient (27°C) temperature. Minor point defects are not included in the defect map. All defective pixels are reference to pixel 1, 1 in the defect maps. See Figure 15: Regions of Interest for the location of pixel 1, 1. www.onsemi.com 17 KAI−01150 TEST DEFINITIONS Test Regions of Interest Overclocking Image Area ROI: Active Area ROI: Center ROI: The test system timing is configured such that the sensor is overclocked in both the vertical and horizontal directions. See Figure 15 for a pictorial representation of the regions of interest. Pixel (1, 1) to Pixel (1320, 736) Pixel (21, 9) to Pixel (1300, 728) Pixel (611, 319) to Pixel (710, 418) Only the Active Area ROI pixels are used for performance and defect tests. VOUTc 12 Dark Rows 1, 1 Horizontal Overclock 1280 x 720 Active Pixels 22 Dark Columns 20 Buffer Columns Pixel 20 Buffer Columns Pixel 21, 9 22 Dark Columns 8 Buffer Rows 8 Buffer Rows 12 Dark Rows VOUTa Figure 15. Regions of Interest Tests voltage has been set such that the charge capacity of the sensor is 680 mV. Global non-uniformity is defined as Dark Field Global Non-Uniformity This test is performed under dark field conditions. The sensor is partitioned into 60 sub regions of interest, each of which is 128 by 120 pixels in size. See Figure 16: Test Sub Regions of Interest. The average signal level of each of the 60 sub regions of interest is calculated. The signal level of each of the sub regions of interest is calculated using the following formula: Global Non−Uniformity + 100 @ ǒ Active Area Standard Deviation Active Area Signal Ǔ Units : % rms Active Area Signal = Active Area Average − Dark Column Average Global Peak to Peak Non-Uniformity This test is performed with the imager illuminated to a level such that the output is at 70% of saturation (approximately 476 mV). Prior to this test being performed the substrate voltage has been set such that the charge capacity of the sensor is 680 mV. The sensor is partitioned into 60 sub regions of interest, each of which is 128 by 120 pixels in size. See Figure 16: Test Sub Regions of Interest. The average signal level of each of the 60 sub regions of interest (ROI) is calculated. The signal level of each of the sub regions of interest is calculated using the following formula: Signal of ROI[i] + (ROI Average in Counts * * Horizontal Overclock Average in Counts) @ @ mV per Count Units : mVpp (millivolts Peak to Peak) Where i = 1 to 144. During this calculation on the 60 sub regions of interest, the maximum and minimum signal levels are found. The dark field global uniformity is then calculated as the maximum signal found minus the minimum signal level found. Signal of ROI[i] + (ROI Average in Counts * Global Non-Uniformity This test is performed with the imager illuminated to a level such that the output is at 70% of saturation (approximately 476 mV). Prior to this test being performed the substrate * Horizontal Overclock Average in Counts) @ @ mV per Count www.onsemi.com 18 KAI−01150 Prior to this test being performed the substrate voltage has been set such that the charge capacity of the sensor is 680 mV. The average signal level of all active pixels is found. The bright and dark thresholds are set as: Where i = 1 to 60. During this calculation on the 60 sub regions of interest, the maximum and minimum signal levels are found. The global peak to peak uniformity is then calculated as: Global Uniformity + 100 @ ǒ Ǔ Dark Defect Threshold = Active Area Signal @ Threshold Max. Signal * Min. Signal Active Area Signal Bright Defect Threshold = Active Area Signal @ Threshold Units : % pp The sensor is then partitioned into 60 sub regions of interest, each of which is 128 by 120 pixels in size. In each region of interest, the average value of all pixels is found. For each region of interest, a pixel is marked defective if it is greater than or equal to the median value of that region of interest plus the bright threshold specified or if it is less than or equal to the median value of that region of interest minus the dark threshold specified. Example for major bright field defective pixels: • Average value of all active pixels is found to be 476 mV. • Dark defect threshold: 476 mV ⋅ 12 % = 57 mV. • Bright defect threshold: 476 mV ⋅ 12 % = 57 mV. • Region of interest #1 selected. This region of interest is pixels 21, 9 to pixels 148, 128. ♦ Median of this region of interest is found to be 470 mV. ♦ Any pixel in this region of interest that is ≥ (470 + 57 mV) 527 mV in intensity will be marked defective. ♦ Any pixel in this region of interest that is ≤ (470 − 57 mV) 413 mV in intensity will be marked defective. • All remaining 60 sub regions of interest are analyzed for defective pixels in the same manner. Center Non-Uniformity This test is performed with the imager illuminated to a level such that the output is at 70% of saturation (approximately 476 mV). Prior to this test being performed the substrate voltage has been set such that the charge capacity of the sensor is 680 mV. Defects are excluded for the calculation of this test. This test is performed on the center 100 by 100 pixels of the sensor. Center uniformity is defined as: Center ROI Uniformity + 100 @ ǒ Center ROI Standard Deviation Center ROI Signal Ǔ Units : % rms Center ROI Signal = Center ROI Average − Dark Colum Average Dark Field Defect Test This test is performed under dark field conditions. The sensor is partitioned into 60 sub regions of interest, each of which is 128 by 120 pixels in size. In each region of interest, the median value of all pixels is found. For each region of interest, a pixel is marked defective if it is greater than or equal to the median value of that region of interest plus the defect threshold specified in the “Defect Definitions” section. Bright Field Defect Test This test is performed with the imager illuminated to a level such that the output is at approximately 476 mV. Test Sub Regions of Interest Pixel (1300,728) Pixel (21,9) 51 52 53 54 55 56 57 58 59 60 41 42 43 44 45 46 47 48 49 50 31 32 33 34 35 36 37 38 39 40 21 22 23 24 25 26 27 28 29 30 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 VOUTa Figure 16. Test Sub Regions of Interest www.onsemi.com 19 KAI−01150 OPERATION Absolute Maximum Ratings description. If the level or the condition is exceeded, the device will be degraded and may be damaged. Operation at these values will reduce MTTF. Absolute maximum rating is defined as a level or condition that should not be exceeded at any time per the Table 17. ABSOLUTE MAXIMUM RATINGS Description Symbol Minimum Maximum Unit Notes Operating Temperature TOP −50 70 °C 1 Humidity RH 5 90 % 2 Output Bias Current IOUT − 60 mA 3 CL − 10 pF Off-Chip Load Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Noise performance will degrade at higher temperatures. 2. T = 25°C. Excessive humidity will degrade MTTF. 3. Total for all outputs. Maximum current is −15 mA for each output. Avoid shorting output pins to ground or any low impedance source during operation. Amplifier bandwidth increases at higher current and lower load capacitance at the expense of reduced gain (sensitivity). Table 18. ABSOLUTE MAXIMUM VOLTAGE RATINGS BETWEEN PINS AND GROUND Description Minimum Maximum Unit Notes VDDa, VOUTa −0.4 17.5 V 1 RDa −0.4 15.5 V 1 V1B, V1T ESD − 0.4 ESD + 24.0 V V2B, V2T, V3B, V3T, V4B, V4T ESD − 0.4 ESD + 14.0 V H1Sa, H1Ba, H2Sa, H2Ba, H2SLa, Ra, OGa ESD − 0.4 ESD + 14.0 V ESD −10.0 0.0 V SUB −0.4 40.0 V 1. a denotes a, b, c or d. 2. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions www.onsemi.com 20 1 2 KAI−01150 Power-Up and Power-Down Sequence Adherence to the power-up and power-down sequence is critical. Failure to follow the proper power-up and power-down sequences may cause damage to the sensor. Do Not Pulse the Electronic Shutter until ESD is Stable V+ VDD SUB Time ESD V− VCCD Low HCCD Low Activate All Other Biases when ESD is Stable and Sub is above 3 V Notes: 1. Activate all other biases when ESD is stable and SUB is above 3 V. 2. Do not pulse the electronic shutter until ESD is stable. 3. VDD cannot be +15 V when SUB is 0 V. 4. The image sensor can be protected from an accidental improper ESD voltage by current limiting the SUB current to less than 10 mA. SUB and VDD must always be greater than GND. ESD must always be less than GND. Placing diodes between SUB, VDD, ESD and ground will protect the sensor from accidental overshoots of SUB, VDD and ESD during power on and power off. See the figure below. Figure 17. Power-Up and Power-Down Sequence The VCCD clock waveform must not have a negative overshoot more than 0.4 V below the ESD voltage. 0.0 V ESD ESD − 0.4 V All VCCD Clock Absolute Maximum Overshoot of 0.4 V Figure 18. VCCD Clock Waveform Example of external diode protection for SUB, VDD and ESD.a denotes a, b, c or d. VDDa SUB GND ESD Figure 19. Example of External Diode Protection www.onsemi.com 21 KAI−01150 DC Bias Operating Conditions Table 19. DC BIAS OPERATING CONDITIONS Pins Symbol Min. Nom. Max. Unit Max. DC Current Notes Reset Drain RDa RD 11.8 12.0 12.2 V 10 mA 1 Output Gate OGa OG −2.2 −2.0 −1.8 V 10 mA 1 Output Amplifier Supply VDDa VDD 14.5 15.0 15.5 V 11.0 mA 1, 2 Ground GND GND 0.0 0.0 0.0 V −1.0 mA Substrate SUB VSUB 5.0 VAB VDD V 50 mA 3, 8 ESD Protection Disable ESD ESD −9.5 −9.0 Vx_L V 50 mA 6, 7, 9 VOUTa IOUT −3.0 −7.0 −10.0 mA − 1, 4, 5 Description Output Bias Current VDDa RDa Ra 1. a denotes a, b, c or d. 2. The maximum DC current is for one output. IDD = IOUT + ISS. See Figure 20. 3. The operating value of the substrate voltage, VAB, will be marked on the shipping container for each device. The value of VAB is set such that the photodiode charge capacity is the nominal PNe (see Specifications). 4. An output load sink must be applied to each VOUT pin to activate each output amplifier. 5. Nominal value required for 40 MHz operation per output. May be reduced for slower data rates and lower noise. 6. Adherence to the power-up and power-down sequence is critical. See Power Up and Power Down Sequence section. 7. ESD maximum value must be less than or equal to V1_L + 0.4 V and V2_L + 0.4 V. 8. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions. 9. Where Vx_L is the level set for V1_L, V2_L, V3_L, or V4_L in the application. IDD HCCD Floating Diffusion IOUT OGa VOUTa ISS Source Follower #1 Figure 20. Output Amplifier www.onsemi.com 22 Source Follower #2 Source Follower #3 KAI−01150 AC Operating Conditions Table 20. CLOCK LEVELS Description Pins (Note 1) Symbol Level Min. Nom. Max. Unit Vertical CCD Clock, Phase 1 V1B, V1T V1_L Low −8.2 −8.0 −7.8 V V1_M Mid −0.2 0.0 0.2 6 nF (Note 6) V1_H High 11.5 12.0 12.5 V2_L Low −8.2 −8.0 −7.8 V V2_H High −0.2 0.0 0.2 6 nF (Note 6) V3_L Low −8.2 −8.0 −7.8 V V3_H High −0.2 0.0 0.2 6 nF (Note 6) V4_L Low −8.2 −8.0 −7.8 V V4_H High −0.2 0.0 0.2 6 nF (Note 6) H1S_L Low −5.2 (Note 7) −4.0 −3.8 V 90 pF (Note 6) H1S_A Amplitude 3.8 4.0 5.2 (Note 7) H1B_L Low −5.2 (Note 7) −4.0 −3.8 V 60 pF (Note 6) H1B_A Amplitude 3.8 4.0 5.2 (Note 7) H2S_L Low −5.2 (Note 7) −4.0 −3.8 V 90 pF (Note 6) H2S_A Amplitude 3.8 4.0 5.2 (Note 7) H2B_L Low −5.2 (Note 7) −4.0 −3.8 V 60 pF (Note 6) H2B_A Amplitude 3.8 4.0 5.2 (Note 7) H2SL_L Low −5.2 −5.0 −4.8 V H2SL_A Amplitude 4.8 5.0 5.2 20 pF (Note 6) R_L (Note 4) Low −3.5 −2.0 −1.5 V 16 pF (Note 6) R_H High 2.5 3.0 4.0 VES High 29.0 30.0 40.0 V 400 pF (Note 6) Vertical CCD Clock, Phase 2 Vertical CCD Clock, Phase 3 Vertical CCD Clock, Phase 4 Horizontal CCD Clock, Phase 1 Storage Horizontal CCD Clock, Phase 1 Barrier Horizontal CCD Clock, Phase 2 Storage Horizontal CCD Clock, Phase 2 Barrier Horizontal CCD Clock, Last Phase (Note 3) Reset Gate Electronic Shutter (Note 5) 1. 2. 3. 4. 5. 6. 7. V2B, V2T V3B, V3T V4B, V4T H1Sa H1Ba H2Sa H2Ba H2SLa Ra SUB Capacitance (Note 2) a denotes a, b, c or d. Capacitance is total for all like named pins. Use separate clock driver for improved speed performance. Reset low should be set to –3 V for signal levels greater than 40,000 electrons. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions. Capacitance values are estimated. If the minimum horizontal clock low level is used (–5.2 V), then the maximum horizontal clock amplitude should be used (5.2 V amplitude) to create a –5.2 V to 0.0 V clock. If a 5 V clock driver is used, the horizontal low level should be set to –5.0 V and the high level should be a set to 0.0 V. www.onsemi.com 23 KAI−01150 The figure below shows the DC bias (VSUB) and AC clock (VES) applied to the SUB pin. Both the DC bias and AC clock are referenced to ground. VES VSUB GND GND Figure 21. DC Bias and AC Clock Applied to the SUB Pin Device Identification The device identification pin (DevID) may be used to determine which ON Semiconductor 5.5 micron pixel interline CCD sensor is being used. Table 21. Description Device Identification Pins Symbol Min. Nom. Max. Unit Max. DC Current Notes DevID DevID 4,000 5,000 6,000 W 50 mA 1, 2, 3 1. Nominal value subject to verification and/or change during release of preliminary specifications. 2. If the Device Identification is not used, it may be left disconnected. 3. After Device Identification resistance has been read during camera initialization, it is recommended that the circuit be disabled to prevent localized heating of the sensor due to current flow through the R_DeviceID resistor. Recommended Circuit Note that V1 must be a different value than V2. V1 V2 R_external DevID ADC R_DeviceID GND KAI−02150 Figure 22. Device Identification Recommended Circuit www.onsemi.com 24 KAI−01150 TIMING Table 22. REQUIREMENTS AND CHARACTERISTICS Description Symbol Min. Nom. Max. Unit Photodiode Transfer tPD 1.0 − − ms VCCD Leading Pedestal t3P 4.0 − − ms VCCD Trailing Pedestal t3D 4.0 − − ms VCCD Transfer Delay tD 1.0 − − ms VCCD Transfer tV 1.0 − − ms VVCR 75 − 100 % 2 tVR, tVF 5 − 10 % 2, 3 tHS 0.2 − − ms HCCD Transfer te 25.0 − − ns Shutter Transfer tSUB 1.0 − − ms Shutter Delay tHD 1.0 − − ms Reset Pulse tR 2.5 − − ns Reset − Video Delay tRV − 2.2 − ns H2SL − Video Delay tHV − 3.1 − ns tLINE 19.0 − − ms 36.1 − − 7.2 − − 14.5 − − Dual HCCD Readout 26.8 − − Single HCCD Readout VCCD Clock Cross-Over VCCD Rise, Fall Times HCCD Delay Line Time Frame Time tFRAME 25 Dual HCCD Readout Single HCCD Readout ms 1. Refer to timing diagrams as shown in Figure 23, Figure 24, Figure 25, Figure 26 and Figure 27. 2. Refer to Figure 27: VCCD Clock Rise Time, Fall Time and Edge Alignment 3. Relative to the pulse width. www.onsemi.com Notes Quad HCCD Readout KAI−01150 Timing Diagrams The timing sequence for the clocked device pins may be represented as one of seven patterns (P1−P7) as shown in the table below. The patterns are defined in Figure 23 and Figure 24. Contact ON Semiconductor Application Engineering for other readout modes. Table 23. TIMING DIAGRAMS Device Pin Quad Readout Dual Readout VOUTa, VOUTb Dual Readout VOUTa, VOUTc Single Readout VOUTa V1T P1T P1B P1T P1B V2T P2T P4B P2T P4B V3T P3T P3B P3T P3B V4T P4T P2B P4T P2B V1B P1B V2B P2B V3B P3B V4B P4B H1Sa P5 H1Ba P5 H2Sa (Note 2) P6 H2Ba P6 Ra P7 H1Sb P5 P5 H1Bb P5 P6 H2Sb (Note 2) P6 P6 H2Bb P6 P5 Rb P7 P7 (Note 1) or Off (Note 3) P7 (Note 1) or Off (Note 3) H1Sc P5 P5 (Note 1) or Off (Note 3) P5 P5 (Note 1) or Off (Note 3) H1Bc P5 P5 (Note 1) or Off (Note 3) P5 P5 (Note 1) or Off (Note 3) H2Sc (Note 2) P6 P6 (Note 1) or Off (Note 3) P6 P6 (Note 1) or Off (Note 3) H2Bc P6 P6 (Note 1) or Off (Note 3) P6 P6 (Note 1) or Off (Note 3) Rc P7 P7 (Note 1) or Off (Note 3) P7 P7 (Note 1) or Off (Note 3) H1Sd P5 P5 (Note 1) or Off (Note 3) P5 P5 (Note 1) or Off (Note 3) H1Bd P5 P5 (Note 1) or Off (Note 3) P6 P5 (Note 1) or Off (Note 3) H2Sd (Note 2) P6 P6 (Note 1) or Off (Note 3) P6 P6 (Note 1) or Off (Note 3) H2Bd P6 P6 (Note 1) or Off (Note 3) P5 P6 (Note 1) or Off (Note 3) Rd P7 P7 (Note 1) or Off (Note 3) P7 (Note 1) or Off (Note 3) P7 (Note 1) or Off (Note 3) #Lines/Frame (Minimum) 380 760 380 760 #Pixels/Line (Minimum) 693 1386 1. For optimal performance of the sensor. May be clocked at a lower frequency. If clocked at a lower frequency, the frequency selected should be a multiple of the frequency used on the a and b register. 2. H2SLx follows the same pattern as H2Sx For optimal speed performance, use a separate clock driver. 3. Off = +5 V. Note that there may be operating conditions (high temperature and/or very bright light sources) that will cause blooming from the unused c/d register into the image area. www.onsemi.com 26 KAI−01150 Photodiode Transfer Timing A row of charge is transferred to the HCCD on the falling edge of V1 as indicated in the P1 pattern below. Using this timing sequence, the leading dummy row or line is combined with the first dark row in the HCCD. The “Last Line” is dependent on readout mode – either 380 or 760 minimum counts required. It is important to note that, in Pattern 1 td 2 t 3p 3 4 t pd t 3d 5 6 general, the rising edge of a vertical clock (patterns P1−P4) should be coincident or slightly leading a falling edge at the same time interval. This is particularly true at the point where P1 returns from the high (3rd level) state to the mid-state when P4 transitions from the low state to the high state. td tv tv P1T t v /2 t v /2 P2T t v /2 t v /2 P3T P4T tv tv P1B t v /2 t v /2 P2B P3B P4B t hs P5 Last Line t hs L1 + Dummy Line L2 P6 P7 Figure 23. Photodiode Transfer Timing P6 pattern). The number of pixels in a row is dependent on readout mode – either 693 or 1386 minimum counts required. Line and Pixel Timing Each row of charge is transferred to the output, as illustrated below, on the falling edge of H2SL (indicated as Pattern tline tv P1T tv P1B ths t e/2 P5 te P6 tr P7 VOUT Pixel 1 Pixel 34 Pixel n Figure 24. Line and Pixel Timing www.onsemi.com 27 KAI−01150 Pixel Timing Detail P5 P6 P7 VOUT trv thv Figure 25. Pixel Timing Detail Frame/Electronic Shutter Timing The SUB pin may be optionally clocked to provide electronic shuttering capability as shown below. The resulting photodiode integration time is defined from the falling edge of SUB to the falling edge of V1 (P1 pattern). Pattern t frame P1T/B SUB P6 t hd t int t sub t hd Figure 26. Frame/Electronic Shutter Timing VCCD Clock Rise Time, Fall Time and Edge Alignment VVCR tV 90% 10% tVR tVF tV tVF tVR Figure 27. VCCD Clock Rise Time, Fall Time and Edge Alignment www.onsemi.com 28 KAI−01150 Line and Pixel Timing − Vertical Binning by 2 tv tv tv ths P1T P2T P3T P4T P1B P2B P3B P4B ths P5 P6 P7 VOUT Pixel 1 Pixel n Pixel 34 Figure 28. Line and Pixel Timing − Vertical Binning by 2 www.onsemi.com 29 KAI−01150 STORAGE AND HANDLING Table 24. STORAGE CONDITIONS Description Symbol Minimum Maximum Units Notes Storage Temperature TST −55 80 °C 1 Humidity RH 5 90 % 2 1. Long-term storage toward the maximum temperature will accelerate color filter degradation. 2. T = 25°C. Excessive humidity will degrade MTTF. For information on ESD and cover glass care and cleanliness, please download the Image Sensor Handling and Best Practices Application Note (AN52561/D) from www.onsemi.com. For quality and reliability information, please download the Quality & Reliability Handbook (HBD851/D) from www.onsemi.com. For information on device numbering and ordering codes, please download the Device Nomenclature technical note (TND310/D) from www.onsemi.com. For information on environmental exposure, please download the Using Interline CCD Image Sensors in High Intensity Lighting Conditions Application Note (AND9183/D) from www.onsemi.com. For information on Standard terms and Conditions of Sale, please download Terms and Conditions from www.onsemi.com. For information on soldering recommendations, please download the Soldering and Mounting Techniques Reference Manual (SOLDERRM/D) from www.onsemi.com. www.onsemi.com 30 KAI−01150 MECHANICAL INFORMATION PGA Completed Assembly Notes: 1. See Ordering Information for marking code. 2. No materials to interfere with clearance through guide holes. 3. The center of the active image is nominally at the center of the package. 4. Die rotation < 0.5 degrees. 5. Glass rotation < 1.5 degrees 6. Internal traces may be exposed on sides of package. Do not allow metal to contact sides of ceramic package. 7. Recommended mounting screws: a.) 1.6 × 0.35 mm (ISO Standard) b.) 0–80 (Unified Fine Thread Standard). 8. Units: IN [MM] Figure 29. PGA Completed Assembly www.onsemi.com 31 KAI−01150 CLCC Completed Assembly Notes: 1. See Ordering Information for marking code. 2. Die rotation < 0.5 degrees. 3. Units: millimeters. Figure 30. CLCC Completed Assembly www.onsemi.com 32 KAI−01150 PGA Cover Glass Notes: 1. Dust/Scratch Count – 12 micron maximum 2. Units: IN [MM] 3. Reflectance Specification a. 420 nm to 435 nm < 2.0% b. 435 nm to 630 nm < 0.8% c. 630 nm to 680 nm < 2.0% Figure 31. PGA Cover Glass www.onsemi.com 33 KAI−01150 CLCC Cover Glass Notes: 1. Dust/Scratch Count – 12 micron maximum 2. Units: millimeter 3. Reflectance Specification a. 420 nm to 435 nm < 2.0% b. 435 nm to 630 nm < 0.8% c. 630 nm to 680 nm < 2.0% Figure 32. CLCC Cover Glass www.onsemi.com 34 KAI−01150 PGA Clear Cover Glass Notes: 1. Dust/Scratch Count – 12 micron maximum 2. Units: IN Figure 33. PGA Clear Cover Glass www.onsemi.com 35 KAI−01150 Cover Glass Transmission 100 90 80 Transmission (%) 70 60 50 40 30 20 10 0 200 300 400 500 600 700 800 900 Wavelength (nm) PGA MAR CLCC MAR PGA Clear NOTE: PGA and CLCC MAR transmission data differ due to in-spec differences from glass vendor. Figure 34. Cover Glass Transmission ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 36 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative KAI−01150/D