LM2904A

LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 Single Supply Dual Operational Amplifiers Utilizing the circuit designs perfected for Quad Operational Amplifiers, these dual operational amplifiers feature low power drain, a common mode input voltage range extending to ground/VEE, and single supply or split supply operation. The LM358 series is equivalent to one−half of an LM324. These amplifiers have several distinct advantages over standard operational amplifier types in single supply applications. They can operate at supply voltages as low as 3.0 V or as high as 32 V, with quiescent currents about one−fifth of those associated with the MC1741 (on a per amplifier basis). The common mode input range includes the negative supply, thereby eliminating the necessity for external biasing components in many applications. The output voltage range also includes the negative power supply voltage. Features http://onsemi.com PDIP−8 N, AN, VN SUFFIX CASE 626 1 8 8 1 SOIC−8 D, VD SUFFIX CASE 751 8 1 • • • • • • • • • • Short Circuit Protected Outputs True Differential Input Stage Single Supply Operation: 3.0 V to 32 V Low Input Bias Currents Internally Compensated Common Mode Range Extends to Negative Supply Single and Split Supply Operation ESD Clamps on the Inputs Increase Ruggedness of the Device without Affecting Operation Pb−Free Packages are Available NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes Micro8] DMR2 SUFFIX CASE 846A PIN CONNECTIONS Output A Inputs A VEE/Gnd 1 2 8 7 − + 3 4 VCC Output B Inputs B − +5 6 (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 11 of this data sheet. © Semiconductor Components Industries, LLC, 2004 1 July, 2004 − Rev. 18 Publication Order Number: LM358/D LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 3.0 V to VCC(max) VCC 1 2 VEE VCC 1 2 1.5 V to VEE(max) VEE/Gnd 1.5 V to VCC(max) Single Supply Figure 1. Split Supplies Output Q15 Q16 Q14 Q13 Q19 5.0 pF Q12 25 40 k Bias Circuitry Common to Both Amplifiers VCC Q22 Q24 Q23 Q18 Inputs Q20 Q11 Q9 Q17 Q2 Q3 Q4 Q21 Q6 Q5 Q8 Q26 Q10 2.0 k VEE/Gnd Q7 Q1 Q25 2.4 k Figure 2. Representative Schematic Diagram (One−Half of Circuit Shown) http://onsemi.com 2 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.) Rating Power Supply Voltages Single Supply Split Supplies Input Differential Voltage Range (Note 1) Input Common Mode Voltage Range (Note 2) Output Short Circuit Duration Junction Temperature Thermal Resistance, Junction−to−Air (Note 3) Storage Temperature Range ESD Protection at any Pin Human Body Model Machine Model Operating Ambient Temperature Range LM258 LM358 LM2904/LM2904A LM2904V, NCV2904 (Note 4) Symbol VCC VCC, VEE VIDR VICR tSC TJ RqJA Tstg Vesd 2000 200 TA −25 to +85 0 to +70 −40 to +105 −40 to +125 °C Value 32 ±16 ±32 −0.3 to 32 Continuous 150 238 −55 to +125 °C °C/W °C V Vdc Vdc Unit Vdc Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Split Power Supplies. 2. For Supply Voltages less than 32 V the absolute maximum input voltage is equal to the supply voltage. 3. RqJA for Case 846A. 4. NCV2904 is qualified for automotive use. http://onsemi.com 3 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = GND, TA = 25°C, unless otherwise noted.) LM258 Characteristic Input Offset Voltage VCC = 5.0 V to 30 V, VIC = 0 V to VCC −1.7 V, VO ] 1.4 V, RS = 0 W TA = 25°C TA = Thigh (Note 5) TA = Tlow (Note 5) Average Temperature Coefficient of Input Offset Voltage TA = Thigh to Tlow (Note 5) Input Offset Current TA = Thigh to Tlow (Note 5) Input Bias Current TA = Thigh to Tlow (Note 5) Average Temperature Coefficient of Input Offset Current TA = Thigh to Tlow (Note 5) Input Common Mode Voltage Range (Note 6), VCC = 30 V VCC = 30 V, TA = Thigh to Tlow Differential Input Voltage Range Large Signal Open Loop Voltage Gain RL = 2.0 kW, VCC = 15 V, For Large VO Swing, TA = Thigh to Tlow (Note 5) Channel Separation 1.0 kHz ≤ f ≤ 20 kHz, Input Referenced Common Mode Rejection RS ≤ 10 kW Power Supply Rejection Output Voltage−High Limit TA = Thigh to Tlow (Note 5) VCC = 5.0 V, RL = 2.0 kW, TA = 25°C VCC = 30 V, RL = 2.0 kW VCC = 30 V, RL = 10 kW Output Voltage−Low Limit VCC = 5.0 V, RL = 10 kW, TA = Thigh to Tlow (Note 5) Output Source Current VID = +1.0 V, VCC = 15 V Output Sink Current VID = −1.0 V, VCC = 15 V VID = −1.0 V, VO = 200 mV Output Short Circuit to Ground (Note 7) Power Supply Current (Total Device) TA = Thigh to Tlow (Note 5) VCC = 30 V, VO = 0 V, RL = ∞ VCC = 5 V, VO = 0 V, RL = ∞ Symbol VIO Min Typ Max Min LM358 Typ Max Unit mV − − − DVIO/DT − 2.0 − − 7.0 5.0 7.0 7.0 − − − − − 2.0 − − 7.0 7.0 9.0 9.0 − mV/°C IIO IIB DIIO/DT − − − − − 3.0 − −45 −50 10 30 100 −150 −300 − − − − − − 5.0 − −45 −50 10 50 150 −250 −500 − nA pA/°C VICR 0 0 − − − 100 − −120 85 28.3 28 VCC − − − − 0 0 − 25 15 − 65 − − − 100 − −120 70 28.3 28 VCC − − − − V VIDR AVOL − 50 25 V V/mV CS CMR − 70 dB dB PSR VOH 65 100 − 65 100 − dB V 3.3 26 27 VOL − 3.5 − 28 5.0 − − − 20 3.3 26 27 − 3.5 − 28 5.0 − − − 20 mV IO + IO − 20 40 − 20 40 − mA 10 12 ISC ICC − − − 20 50 40 − − 60 10 12 − 20 50 40 − − 60 mA mA mA mA 1.5 0.7 3.0 1.2 − − 1.5 0.7 3.0 1.2 5. LM258: Tlow = −25°C, Thigh = +85°C LM358: Tlow = 0°C, Thigh = +70°C LM2904/LM2904A: Tlow = −40°C, Thigh = +105°C LM2904V & NCV2904: Tlow = −40°C, Thigh = +125°C NCV2904 is qualified for automotive use. 6. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common mode voltage range is VCC − 1.7 V. 7. Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. http://onsemi.com 4 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.) LM2904 Characteristic Input Offset Voltage VCC = 5.0 V to 30 V, VIC = 0 V to VCC −1.7 V, VO ] 1.4 V, RS = 0 W TA = 25°C TA = Thigh (Note 8) TA = Tlow (Note 8) Average Temperature Coefficient of Input Offset Voltage TA = Thigh to Tlow (Note 8) Input Offset Current TA = Thigh to Tlow (Note 8) Input Bias Current TA = Thigh to Tlow (Note 8) Average Temperature Coefficient of Input Offset Current TA = Thigh to Tlow (Note 8) Input Common Mode Voltage Range (Note 9), VCC = 30 V VCC = 30 V, TA = Thigh to Tlow Differential Input Voltage Range Large Signal Open Loop Voltage Gain RL = 2.0 kW, VCC = 15 V, For Large VO Swing, TA = Thigh to Tlow (Note 8) Channel Separation 1.0 kHz ≤ f ≤ 20 kHz, Input Referenced Common Mode Rejection RS ≤ 10 kW Power Supply Rejection Output Voltage−High Limit TA = Thigh to Tlow (Note 8) VCC = 5.0 V, RL = 2.0 kW, TA = 25°C VCC = 30 V, RL = 2.0 kW VCC = 30 V, RL = 10 kW Output Voltage−Low Limit VCC = 5.0 V, RL = 10 kW, TA = Thigh to Tlow (Note 8) Output Source Current VID = +1.0 V, VCC = 15 V Output Sink Current VID = −1.0 V, VCC = 15 V VID = −1.0 V, VO = 200 mV Output Short Circuit to Ground (Note 10) Power Supply Current (Total Device) TA = Thigh to Tlow (Note 8) VCC = 30 V, VO = 0 V, RL = ∞ VCC = 5 V, VO = 0 V, RL = ∞ Symbol VIO Min Typ Max Min LM2904A Typ Max LM2904V, NCV2904 Min Typ Max Unit mV − − − DVIO/DT − 2.0 − − 7.0 7.0 10 10 − − − − − 2.0 − − 7.0 7.0 10 10 − − − − − − − − 7.0 7.0 13 10 − mV/°C IIO IIB DIIO/DT − − − − − 5.0 45 −45 −50 10 50 200 −250 −500 − − − − − − 5.0 45 −45 −50 10 50 200 −100 −250 − − − − − − 5.0 45 −45 −50 10 50 200 −250 −500 − nA pA/°C VICR 0 0 − − − 100 − −120 70 24.3 24 VCC − − − − 0 0 − 25 15 − 50 − − − 100 − −120 70 24.3 24 VCC − − − − 0 0 − 25 15 − 50 − − − 100 − −120 70 24.3 24 VCC − − − − V VIDR AVOL − 25 15 V V/mV CS CMR − 50 dB dB PSR VOH 50 100 − 50 100 − 50 100 − dB V 3.3 22 23 VOL − 3.5 − 24 5.0 − − − 20 3.3 22 23 − 3.5 − 24 5.0 − − − 20 3.3 22 23 − 3.5 − 24 5.0 − − − 20 mV IO + IO − 20 40 − 20 40 − 20 40 − mA 10 − ISC ICC − − − 20 − 40 − − 60 10 − − 20 − 40 − − 60 10 − − 20 − 40 − − 60 mA mA mA mA 1.5 0.7 3.0 1.2 − − 1.5 0.7 3.0 1.2 − − 1.5 0.7 3.0 1.2 8. LM258: Tlow = −25°C, Thigh = +85°C LM358: Tlow = 0°C, Thigh = +70°C LM2904V & NCV2904: Tlow = −40°C, Thigh = +125°C LM2904/LM2904A: Tlow = −40°C, Thigh = +105°C NCV2904 is qualified for automotive use. 9. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common mode voltage range is VCC − 1.7 V. 10. Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. http://onsemi.com 5 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 CIRCUIT DESCRIPTION The LM358 series is made using two internally compensated, two−stage operational amplifiers. The first stage of each consists of differential input devices Q20 and Q18 with input buffer transistors Q21 and Q17 and the differential to single ended converter Q3 and Q4. The first stage performs not only the first stage gain function but also performs the level shifting and transconductance reduction functions. By reducing the transconductance, a smaller compensation capacitor (only 5.0 pF) can be employed, thus saving chip area. The transconductance reduction is accomplished by splitting the collectors of Q20 and Q18. Another feature of this input stage is that the input common mode range can include the negative supply or ground, in single supply operation, without saturating either the input devices or the differential to single−ended converter. The second stage consists of a standard current source load amplifier stage. Each amplifier is biased from an internal−voltage regulator which has a low temperature coefficient thus giving each amplifier good temperature characteristics as well as excellent power supply rejection. VCC = 15 Vdc RL = 2.0 kW TA = 25°C 1.0 V/DIV 5.0 ms/DIV Figure 3. Large Signal Voltage Follower Response AVOL, OPEN LOOP VOLTAGE GAIN (dB) 20 18 VI , INPUT VOLTAGE (V) 16 14 12 10 8.0 6.0 4.0 2.0 0 0 2.0 4.0 6.0 8.0 10 12 14 16 VCC/VEE, POWER SUPPLY VOLTAGES (V) 18 20 Negative Positive 120 100 80 60 40 20 0 −20 1.0 10 100 1.0 k 10 k 100 k 1.0 M f, FREQUENCY (Hz) VCC = 15 V VEE = Gnd TA = 25°C Figure 4. Input Voltage Range Figure 5. Large−Signal Open Loop Voltage Gain http://onsemi.com 6 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 14 VOR , OUTPUT VOLTAGE RANGE (Vpp ) VO , OUTPUT VOLTAGE (mV) 12 10 8.0 6.0 4.0 2.0 0 1.0 10 100 f, FREQUENCY (kHz) 1000 RL = 2.0 kW VCC = 15 V VEE = Gnd Gain = −100 RI = 1.0 kW RF = 100 kW 550 500 450 400 350 300 250 200 0 0 1.0 2.0 3.0 4.0 t, TIME (ms) 5.0 6.0 7.0 8.0 Input VCC = 30 V VEE = Gnd TA = 25°C CL = 50 pF Output Figure 6. Large−Signal Frequency Response Figure 7. Small Signal Voltage Follower Pulse Response (Noninverting) 2.4 I CC , POWER SUPPLY CURRENT (mA) 2.1 1.8 1.5 1.2 0.9 0.6 0.3 0 0 5.0 10 15 20 25 VCC, POWER SUPPLY VOLTAGE (V) 30 35 I IB , INPUT BIAS CURRENT (nA) TA = 25°C RL = R 90 80 70 0 2.0 4.0 6.0 8.0 10 12 14 16 VCC, POWER SUPPLY VOLTAGE (V) 18 20 Figure 8. Power Supply Current versus Power Supply Voltage Figure 9. Input Bias Current versus Supply Voltage http://onsemi.com 7 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 50 k R1 VCC VCC R2 − 1/2 5.0 k 10 k VO Vref − 1/2 VCC VO fo = R 1 2 p RC MC1403 LM358 2.5 V + Vref = VO = 2.5 V (1 + R1 ) R2 1 V 2 CC R LM358 + C C For: fo = 1.0 kHz R = 16 kW C = 0.01 mF Figure 10. Voltage Reference Figure 11. Wien Bridge Oscillator e1 + 1/2 1 CR R R2 R1 eo Vref Vin Hysteresis VOH VO VO LM358 − a R1 b R1 − 1/2 1/2 − R1 + 1/2 LM358 + LM358 − 1 CR R VOL VinL Vref VinH LM358 e2 + R1 (V − V )+ Vref VinL = R1 + R2 OL ref VinH = R1 (V − V ) + Vref R1 + R2 OH ref R1 (VOH − VOL) R1 + R2 eo = C (1 + a + b) (e2 − e1) H= Figure 12. High Impedance Differential Amplifier Figure 13. Comparator with Hysteresis R Vin C1 R2 − C R 1/2 R 100 k C − 100 k − 1/2 1 2p RC R1 = QR fo = R2 = R1 TBP R3 = TN R2 C1 = 10 C For: fo Q TBP TN = 1.0 kHz = 10 =1 =1 R C R1 R2 R3 Vref = 1 V 2 CC 1/2 LM358 + LM358 + LM358 Vref R2 R1 Vref Bandpass Output 1/2 + R3 − Vref C1 Notch Output = 160 kW = 0.001 mF = 1.6 MW = 1.6 MW = 1.6 MW LM358 + Vref Where: TBP = Center Frequency Gain TN = Passband Notch Gain Figure 14. Bi−Quad Filter http://onsemi.com 8 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 VCC C Vin R1 C R3 1/2 − R2 Vref LM358 + VO CO CO = 10 C 1 Vref = 2 VCC Given: fo = center frequency A(fo) = gain at center frequency Choose value fo, C Vref = Vref 1 V 2 CC + 1/2 Triangle Wave Output R3 75 k R1 Vref Rf f= R1 + RC 4 CRf R1 if, R3 = R2 R1 R2 + R1 100 k R2 300 k + 1/2 Then: R3 = R1 = R2 = Q p fo C R3 2 A(fo) R1 R3 4Q2 R1 −R3 Qo fo < 0.1 BW LM358 − LM358 − C Square Wave Output For less than 10% error from operational amplifier. Where fo and BW are expressed in Hz. If source impedance varies, filter may be preceded with voltage follower buffer to stabilize filter parameters. Figure 15. Function Generator Figure 16. Multiple Feedback Bandpass Filter http://onsemi.com 9 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 ORDERING INFORMATION Device LM358D LM358DR2 LM358DR2G LM358DMR2 LM358DMR2G LM358N LM358NG LM258D LM258DR2 LM258DR2G LM258DMR2 LM258N LM2904D LM2904DR2 LM2904DR2G LM2904DMR2 LM2904DMR2G LM2904N LM2904ADMR2 LM2904AN LM2904VD LM2904VDG LM2904VDR2 LM2904VDMR2 LM2904VN NCV2904DR2* NCV2904DMR2* −40°C to +125°C −25°C to +85°C Operating Temperature Range Package SOIC−8 SOIC−8 SOIC−8 (Pb−Free) 0°C to +70°C +70 Micro8 Micro8 (Pb−Free) PDIP−8 PDIP−8 (Pb−Free) SOIC−8 SOIC−8 SOIC−8 (Pb−Free) Micro8 PDIP−8 SOIC−8 SOIC−8 SOIC−8 (Pb−Free) −40°C to +105°C 40 Micro8 Micro8 (Pb−Free) PDIP−8 Micro8 PDIP−8 SOIC−8 SOIC−8 (Pb−Free) SOIC−8 Micro8 PDIP−8 SOIC−8 Micro8 Shipping† 98 Units/Rail 2500 Tape & Reel 2500 Tape & Reel 4000 Tape & Reel 4000 Tape & Reel 50 Units/Rail 50 Units/Rail 98 Units/Rail 2500 Tape & Reel 2500 Tape & Reel 4000 Tape & Reel 50 Units/Rail 98 Units/Rail 2500 Tape & Reel 2500 Tape & Reel 2500 Tape & Reel 2500 Tape & Reel 50 Units/Rail 4000 Tape & Reel 50 Units/Rail 98 Units/Rail 98 Units/Rail 2500 Tape & Reel 4000 Tape & Reel 50 Units/Rail 2500 Tape & Reel 4000 Tape & Reel *NCV2904 is qualified for automotive use. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 10 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 MARKING DIAGRAMS PDIP−8 N SUFFIX CASE 626 8 LMx58N AWL YYWW 1 1 8 LM2904N AWL YYWW 1 8 PDIP−8 AN SUFFIX CASE 626 8 LM2904AN AWL YYWW 1 PDIP−8 VN SUFFIX CASE 626 LM2904VN AWL YYWW SOIC−8 D SUFFIX CASE 751 8 LMx58 ALYW 1 1 8 2904 ALYW SOIC−8 VD SUFFIX CASE 751 8 2904V ALYW 1 * Micro8 DMR2 SUFFIX CASE 846A 8 x58 AYW 8 2904 AYW 8 904A AYW 8 904V AYW * 1 1 1 1 x A WL, L YY, Y WW, W = 2 or 3 = Assembly Location = Wafer Lot = Year = Work Week *This diagram also applies to NCV2904 http://onsemi.com 11 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 PACKAGE DIMENSIONS PDIP−8 N, AN, VN SUFFIX CASE 626−05 ISSUE L NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC −−− 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC −−− 10_ 0.030 0.040 8 5 −B− 1 4 F NOTE 2 −A− L C −T− SEATING PLANE J N D K M M H G 0.13 (0.005) TA M B M http://onsemi.com 12 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 PACKAGE DIMENSIONS SOIC−8 D, VD SUFFIX CASE 751−07 ISSUE AB NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244 −X− A 8 5 B 1 4 S 0.25 (0.010) M Y M −Y− G C −Z− H D 0.25 (0.010) M SEATING PLANE K N X 45 _ 0.10 (0.004) M J ZY S X S DIM A B C D G H J K M N S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 13 LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904 PACKAGE DIMENSIONS Micro8 DMR2 SUFFIX CASE 846A−02 ISSUE F −B− −A− K PIN 1 ID NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A−01 OBSOLETE, NEW STANDARD 846A−02. DIM A B C D G H J K L MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 −−− 1.10 0.25 0.40 0.65 BSC 0.05 0.15 0.13 0.23 4.75 5.05 0.40 0.70 INCHES MIN MAX 0.114 0.122 0.114 0.122 −−− 0.043 0.010 0.016 0.026 BSC 0.002 0.006 0.005 0.009 0.187 0.199 0.016 0.028 G D 8 PL 0.08 (0.003) M TB S A S −T− PLANE 0.038 (0.0015) H SEATING C J L SOLDERING FOOTPRINT* 8X 1.04 0.041 0.38 0.015 8X 3.20 0.126 4.24 0.167 5.28 0.208 6X 0.65 0.0256 SCALE 8:1 mm inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Micro8 is a trademark of International Rectifier. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. http://onsemi.com 14 LM358/D