DATA SHEET
www.onsemi.com
Operational Amplifier,
Rail-to-Rail, Low Input Bias
Current, 1.8 V to 5 V
Single-Supply
SC70−5
SQ SUFFIX
CASE 419A
STYLES 3
LMV301
MARKING DIAGRAM
The LMV301 CMOS operational amplifier can operate over a
power supply range from 1.8 V to 5 V and has a quiescent current of
less than 200 mA, maximum, making it ideal for portable
battery−operated applications such as notebook computers, PDA’s and
medical equipment. Low input bias current and high input impedance
make it highly tolerant of high source−impedance signal−sources such
as photodiodes and pH probes. In addition, the LMV301’s excellent
rail−to−rail performance will enhance the signal−to−noise
performance of any application together with an output stage capable
of easily driving a 600 W resistive load and up to 1000 pF capacitive
load.
Features
•
•
•
•
•
•
•
Single Supply Operation (or $VS/2)
VS from 1.8 V to 5 V
Low Quiescent Current: 185 mA, Max with VS = 1.8 V
Rail−to−Rail Output Swing
Low Bias Current: 35 pA, max
No Output Phase−Reversal when the Inputs are Overdriven
These are Pb−Free Devices
Typical Applications
•
•
•
•
•
•
•
•
Portable Battery−Powered Instruments
Notebook Computers and PDAs
Cell Phones and Mobile Communication
Digital Cameras
Photodiode Amplifiers
Transducer Amplifiers
Medical Instrumentation
Consumer Products
© Semiconductor Components Industries, LLC, 2011
October, 2021 − Rev. 4
AAD MG
G
LMV301
M
G
= Specific Device Code
= Date Code
= Pb−Free Package
(Note: Microdot may be in either location)
*Date Code orientation and/or position may
vary depending upon manufacturing location.
PIN CONNECTION
+IN
1
VEE
2
−IN
3
5
VCC
4
OUTPUT
+
−
STYLE 3 PINOUT
ORDERING INFORMATION
See detailed ordering and shipping information in the
dimensions section on page 11 of this data sheet.
1
Publication Order Number:
LMV301/D
LMV301
MAXIMUM RATINGS
Symbol
VS
Rating
Power Supply (Operating Voltage Range VS = 1.8 V to 5.0 V)
Value
Unit
5.5
V
VIDR
Input Differential Voltage
±Supply Voltage
V
VICR
Input Common Mode Voltage Range
−0.5 to (V+) + 0.5
V
10
mA
Maximum Input Current
tSo
Output Short Circuit (Note 1)
Continuous
TJ
Maximum Junction Temperature (Operating Range −40°C to 85°C)
150
°C
JA
Thermal Resistance (5−Pin SC70−5)
280
°C/W
Tstg
Storage Temperature
−65 to 150
°C
VESD
Mounting Temperature (Infrared or Convection (30 sec))
260
ESD Tolerance
Machine Model
Human Body Model
100
1500
V
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Continuous short−circuit to ground operation at elevated ambient temperature can result in exceeding the maximum allowed junction
temperature of 150°C. Output currents in excess of 45 mA over long term may adversely affect reliability. Also, shorting output to V+ will
adversely affect reliability; likewise shorting output to V− will adversely affect reliability.
www.onsemi.com
2
LMV301
1.8 V DC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, VCC = 1.8 V,
RL = 1 MW, VEE = 0 V, VO = VCC/2)
Parameter
Input Offset Voltage
Input Offset Voltage Average Drift
Input Bias Current (Note 2)
Symbol
Condition
VIO
TCVIO
Min
Typ
Max
Unit
TA = −40°C to +85°C
1.7
9
mV
TA = −40°C to +85°C
5
IB
3
TA = −40°C to +85°C
mV/°C
35
pA
50
Common Mode Rejection Ratio
CMRR
0 V v VCM v 0.9 V
50
63
dB
Power Supply Rejection Ratio
PSRR
1.8 V v VCC v 5 V,
VO = 1 V, VCM = 1 V
62
100
dB
Input Common−Mode Voltage
Range
VCM
For CMRR ≥ 50 dB
0 to
0.9
−0.2
to 0.9
V
100
dB
Large Signal Voltage Gain (Note 2)
AV
RL = 600W
83
TA = −40°C to +85°C
80
RL = 2 kW
83
TA = −40°C to +85°C
80
VOH
RL = 600 W to 0.9 V
TA = −40°C to +85°C
1.65
1.63
VOL
RL = 600 W to 0.9 V
TA = −40°C to +85°C
VOH
RL = 2 kW to 0.9 V
TA = −40°C to +85°C
VOL
RL = 2 kW to 0.9 V
TA = −40°C to +85°C
Output Short Circuit Current
(Note 2)
IO
Sourcing = VO = 0 V
Sinking = VO = 1.8 V
Supply Current
ICC
TA = −40°C to +85°C
Output Swing
100
V
75
1.5
1.4
1.76
25
10
20
100
120
mV
V
35
40
60
160
mV
mA
185
mA
1.8 V AC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, VCC = 1.8 V,
RL = 1 MW, VEE = 0 V, VO = VCC/2)
Parameter
Symbol
Gain Bandwidth Product
GBWP
Slew Rate
Condition
SR
CL = 200 pF
Min
Typ
Max
Unit
1
V/ms
1
MHz
Phase Margin
Qm
60
°
Gain Margin
Gm
10
dB
Input−Referred Voltage Noise
en
f = 50 kHz
50
nV/√Hz
THD
AV = +1, V − 1 VPP,
RL = 10 kW, f = 1 kHz
0.01
%
Total Harmonic Distortion
2. Guaranteed by design and/or characterization.
www.onsemi.com
3
LMV301
2.7 V DC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, VCC = 2.7 V,
RL = 1 MW, VEE = 0 V, VO = VCC/2)
Parameter
Input Offset Voltage
Input Offset Voltage Average Drift
Input Bias Current (Note 2)
Symbol
Condition
VIO
TCVIO
Min
Typ
Max
Unit
TA = −40°C to +85°C
1.7
9
mV
TA = −40°C to +85°C
5
IB
3
TA = −40°C to +85°C
mV/°C
35
pA
50
Common Mode Rejection Ratio
CMRR
0 V v VCM v 1.35 V
50
63
dB
Power Supply Rejection Ratio
PSRR
1.8 V v VCC v 5 V,
VO = 1 V, VCM = 1 V
62
100
dB
Input Common−Mode Voltage
Range
VCM
For CMRR ≥ 50 dB
0 to
1.35
−0.2
to1.35
V
100
dB
Large Signal Voltage Gain (Note 2)
AV
RL = 600 W
83
TA = −40°C to +85°C
80
RL = 2 kW
83
TA = −40°C to +85°C
80
VOH
RL = 600 W to 1.35 V
TA = −40°C to +85°C
2.55
2.53
VOL
RL = 600 W to 1.35 V
TA = −40°C to +85°C
VOH
RL = 2 kW to 1.35 V
TA = −40°C to +85°C
VOL
RL = 2 kW to 1.35 V
TA = −40°C to +85°C
Output Short Circuit Current
(Note 2)
IO
Sourcing = VO = 0 V
Sinking = VO = 2.7 V
Supply Current
ICC
TA = −40°C to +85°C
Output Swing
100
2.62
78
2.65
2.64
100
280
2.675
75
10
20
V
mV
V
100
110
60
160
mV
mA
185
mA
2.7 V AC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, VCC = 2.7 V,
RL = 1 MW, VEE = 0 V, VO = VCC/2)
Parameter
Symbol
Gain Bandwidth Product
GBWP
Slew Rate
Condition
SR
CL = 200 pF
Min
Typ
Max
Unit
1
V/ms
1
MHz
Phase Margin
Qm
60
°
Gain Margin
Gm
10
dB
Input−Referred Voltage Noise
en
f = 50 kHz
50
nV/√Hz
THD
AV = +1, V − 1 VPP,
RL = 10 kW, f = 1 kHz
0.01
%
Total Harmonic Distortion
2. Guaranteed by design and/or characterization.
www.onsemi.com
4
LMV301
5.0 V DC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, VCC = 5.0 V,
RL = 1 MW, VEE = 0 V, VO = VCC/2)
Parameter
Input Offset Voltage
Input Offset Voltage Average Drift
Input Bias Current (Note 2)
Symbol
Condition
VIO
TCVIO
Min
Typ
Max
Unit
TA = −40°C to +85°C
1.7
9
mV
TA = −40°C to +85°C
5
IB
3
TA = −40°C to +85°C
mV/°C
35
pA
50
Common Mode Rejection Ratio
CMRR
0 V v VCM v 4 V
50
63
dB
Power Supply Rejection Ratio
PSRR
1.8 V v VCC v 5 V,
VO = 1 V, VCM = 1 V
62
100
dB
Input Common−Mode Voltage
Range
VCM
For CMRR ≥ 50 dB
0 to 4
−0.2
to 4.2
V
100
dB
Large Signal Voltage Gain (Note 2)
AV
RL = 600 W
83
TA = −40°C to +85°C
80
RL = 2 kW
83
TA = −40°C to +85°C
80
VOH
RL = 600 W to 2.5 V
TA = −40°C to +85°C
4.850
4.840
VOL
RL = 600 W to 2.5 V
TA = −40°C to +85°C
VOH
RL = 2 kW to 2.5 V
TA = −40°C to +85°C
VOL
RL = 2 kW to 2.5 V
TA = −40°C to +85°C
Output Short Circuit Current
(Note 2)
IO
Sourcing = VO = 0 V
Sinking = VO = 5 V
Supply Current
ICC
TA = −40°C to +85°C
Output Swing
100
V
150
160
4.935
4.900
V
65
75
10
10
mV
60
160
mV
mA
200
µA
5.0 V AC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, VCC = 5.0 V,
RL = 1 MW, VEE = 0 V, VO = VCC/2)
Parameter
Symbol
Gain Bandwidth Product
GBWP
Slew Rate
Condition
SR
CL = 200 pF
Min
Typ
Max
Unit
1
V/ms
1
MHz
Phase Margin
Qm
60
°
Gain Margin
Gm
10
dB
Input−Referred Voltage Noise
en
f = 50 kHz
50
nV/√Hz
THD
AV = +1, V − 1 VPP,
RL = 10 kW, f = 1 kHz
0.01
%
Total Harmonic Distortion
2. Guaranteed by design and/or characterization.
www.onsemi.com
5
LMV301
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
100
40
90
PHASE MARGIN (°)
50
GAIN (dB)
30
20
10
Over −40°C to +85°C
Same Gain $1.8 dB (Typ)
0
70
60
50
−10
10k
80
100k
1M
FREQUENCY (Hz)
40
10M
10k
90
75
80
70
70
65
60
60
CMRR (dB)
CMRR (dB)
80
50
40
55
45
20
40
10
35
10k
30
−0.5
100k
VS = 2.7 V
f = 10 kHz
50
30
1k
10M
Figure 2. Open Loop Phase Margin
(RL = 2 kW, TA = 255C)
100
100
1M
FREQUENCY (Hz)
Figure 1. Open Loop Frequency Response
(RL = 2 kW, TA = 255C, VS = 5 V)
0
10
100k
0
0.5
1
1.5
2
2.5
FREQUENCY (Hz)
INPUT COMMON MODE VOLTAGE (V)
Figure 3. CMRR vs. Frequency
(RL = 5 kW, VS = 5 V)
Figure 4. CMRR vs. Input Common Mode
Voltage
80
3
100
90
70
80
60
PSRR (dB)
CMRR (dB)
70
VS = 5 V
f = 10 kHz
50
60
50
40
30
20
40
10
30
−1
0
1
2
3
4
0
1k
5
10k
100k
1M
INPUT COMMON MODE VOLTAGE (V)
FREQUENCY (Hz)
Figure 5. CMRR vs. Input Common Mode
Voltage
Figure 6. PSRR vs. Frequency
(RL = 5 kW, VS = 2.7 V, +PSRR)
www.onsemi.com
6
10M
LMV301
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
90
100
80
90
70
80
70
60
PSRR (dB)
PSRR (dB)
60
50
40
30
50
40
30
20
20
10
10
0
1k
10k
100k
1M
0
1k
10M
10k
FREQUENCY (Hz)
90
80
4
70
3.5
60
3
VOS (mV)
PSRR (dB)
5
4.5
50
40
2.5
2
30
1.5
20
1
10
0.5
10k
100k
1M
0
10M
VS = 2.7 V
0
0.5
FREQUENCY (Hz)
100
90
QUIESCENT CURRENT (mA)
5
4
VOS (mV)
3.5
3
2.5
2
1.5
VS = 5.0 V
0.5
0
0.5
1
1.5
2
2.5
3
1.5
2
2.5
3
Figure 10. VOS vs CMR
4.5
0
1
VCM (V)
Figure 9. PSRR vs. Frequency
(RL = 5 kW, VS = 5 V, −PSRR)
1
10M
Figure 8. PSRR vs. Frequency
(RL = 5 kW, VS = 5 V, +PSRR)
100
1k
1M
FREQUENCY (Hz)
Figure 7. PSRR vs. Frequency
(RL = 5 kW, VS = 2.7 V, −PSRR)
0
100k
3.5
4
4.5
80
70
60
50
40
30
20
10
0
5
1.8
2.2
2.6
3
3.4
3.8
4.2
4.6
VCM (V)
SUPPLY VOLTAGE (V)
Figure 11. VOS vs CMR
Figure 12. Supply Current vs. Supply Voltage
www.onsemi.com
7
5
LMV301
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
1
0
VOUT REFERENCED TO V+ (V)
RL = 10 kW
Vout = 1 VPP
Av = +1
(%)
0.1
0.01
100
1k
10k
−0.03
−0.04
−0.05
−0.06
−0.07
−0.08
−0.09
−0.1
2.5
4.5
5
Figure 14. Output Voltage Swing vs Supply
Voltage (RL = 10k)
−20
0.08
0.07
0.06
0.05
0.04
0.03
0.02
3
3.5
4
SUPPLY VOLTAGE (V)
−60
−80
−100
−120
−140
Negative Swing
0.01
−40
4.5
−160
5
0
−20
100
SOURCE CURRENT (mA)
120
−40
−60
−80
−100
2
3
4
1
1.5
2
2.5
Figure 16. Sink Current vs. Output Voltage
VS = 2.7 V
0
1
0.5
VOUT REFERENCED TO V− (V)
Figure 15. Output Voltage Swing vs Supply
Voltage (RL = 10k)
SINK CURRENT (mA)
4
Figure 13. THD+N vs Frequency
0.09
0
3.5
SUPPLY VOLTAGE (V)
0
−120
3
(Hz)
0.1
0
2.5
Positive Swing
−0.02
100k
SINK CURRENT (mA)
VOUT REFERENCED TO V− (V)
0.001
10
−0.01
80
60
40
20
0
5
VOUT REFERENCED TO V− (V)
0
0.5
1.0
1.5
2.0
VOUT REFERENCED TO V+ (V)
Figure 17. Sink Current vs. Output Voltage
VS = 5.0 V
Figure 18. Source Current vs. Output Voltage
VS = 2.7 V
www.onsemi.com
8
2.5
LMV301
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
110
RL = 2 kW
AV = 1
50 mV/div
2 ms/div
SOURCE CURRENT (mA)
100
90
80
70
60
50
40
30
20
10
0
0
1
2
3
4
VOUT REFERENCED TO V+ (V)
5
Figure 19. Source Current vs. Output Voltage
VS = 5.0 V
Figure 20. Settling Time vs. Capacitive Load
50 mV/div
2 ms/div
RL = 1 MW
AV = 1
50 mV/div
2 ms/div
Non−Inverting (G = +1)
Input
Output
Figure 21. Settling Time vs. Capacitive Load
Figure 22. Step Response − Small Signal
50 mV/div
2 ms/div
1 V/div
2 ms/div
Non−Inverting (G = +1)
Inverting (G = −1)
Input
Input
Output
Output
Figure 24. Step Response − Large Signal
Figure 23. Step Response − Small Signal
www.onsemi.com
9
LMV301
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
1 V/div
2 ms/div
Inverting (G = −1)
Input
Output
Figure 25. Step Response − Large Signal
www.onsemi.com
10
LMV301
APPLICATIONS
50 k
R1
5.0 k
VCC
VCC
R2
10 k
MC1403
2.5 V
VO
LMV301
VO
LMV301
VCC
−
Vref
−
+
+
1
V ref + V CC
2
R1
V O + 2.5 V(1 )
)
R2
R
R
Figure 26. Voltage Reference
fO +
For: fo = 1.0 kHz
R = 16 kW
C = 0.01 mF
C
C
1
2pRC
Figure 27. Wien Bridge Oscillator
VCC
C
R1
Vin
R2
C
R3
−
Hysteresis
R1
LMV301
−
Vin
VO
VOL
CO = 10 C
Vref
VO
+
VO
+
R2
VOH
Vref
CO
LMV301
VinL
Given: fo = center frequency
A(fo) = gain at center frequency
VinH
Choose value fo, C
Q
Then : R3 +
pf O C
Vref
R1
(V OL * V ref) ) V ref
R1 ) R2
R1
V inH +
(V OH * V ref) ) V ref
R1 ) R2
R1
H+
(V OH * V OL)
R1 ) R2
V inL +
R1 +
R2 +
R3
2 A(f O)
R1 R3
4Q 2 R1 * R3
Figure 28. Comparator with Hysteresis
For less than 10% error from operational amplifier,
((QO fO)/BW) < 0.1 where fo and BW are expressed in Hz.
If source impedance varies, filter may be preceded with
voltage follower buffer to stabilize filter parameters.
Figure 29. Multiple Feedback Bandpass Filter
ORDERING INFORMATION
Device
LMV301SQ3T2G
Pinout Style
Marking
Package
Shipping†
Style 3
AAD
SC70−5
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
11
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
SCALE 2:1
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
G
5
4
−B−
S
1
2
DATE 17 JAN 2013
DIM
A
B
C
D
G
H
J
K
N
S
3
D 5 PL
0.2 (0.008)
B
M
M
N
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
J
GENERIC MARKING
DIAGRAM*
C
K
H
XXXMG
G
SOLDER FOOTPRINT
0.50
0.0197
XXX = Specific Device Code
M
= Date Code
G
= Pb−Free Package
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
SCALE 20:1
(Note: Microdot may be in either location)
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
mm Ǔ
ǒinches
STYLE 1:
PIN 1. BASE
2. EMITTER
3. BASE
4. COLLECTOR
5. COLLECTOR
STYLE 2:
PIN 1. ANODE
2. EMITTER
3. BASE
4. COLLECTOR
5. CATHODE
STYLE 3:
PIN 1. ANODE 1
2. N/C
3. ANODE 2
4. CATHODE 2
5. CATHODE 1
STYLE 4:
PIN 1. SOURCE 1
2. DRAIN 1/2
3. SOURCE 1
4. GATE 1
5. GATE 2
STYLE 6:
PIN 1. EMITTER 2
2. BASE 2
3. EMITTER 1
4. COLLECTOR
5. COLLECTOR 2/BASE 1
STYLE 7:
PIN 1. BASE
2. EMITTER
3. BASE
4. COLLECTOR
5. COLLECTOR
STYLE 8:
PIN 1. CATHODE
2. COLLECTOR
3. N/C
4. BASE
5. EMITTER
STYLE 9:
PIN 1. ANODE
2. CATHODE
3. ANODE
4. ANODE
5. ANODE
DOCUMENT NUMBER:
DESCRIPTION:
98ASB42984B
STYLE 5:
PIN 1. CATHODE
2. COMMON ANODE
3. CATHODE 2
4. CATHODE 3
5. CATHODE 4
Note: Please refer to datasheet for
style callout. If style type is not called
out in the datasheet refer to the device
datasheet pinout or pin assignment.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
SC−88A (SC−70−5/SOT−353)
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
TSOP−5
CASE 483
ISSUE N
5
1
SCALE 2:1
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
D 5X
NOTE 5
2X
DATE 12 AUG 2020
0.20 C A B
0.10 T
M
2X
0.20 T
5
B
1
4
2
B
S
3
K
DETAIL Z
G
A
A
TOP VIEW
DIM
A
B
C
D
G
H
J
K
M
S
DETAIL Z
J
C
0.05
H
C
SIDE VIEW
SEATING
PLANE
END VIEW
GENERIC
MARKING DIAGRAM*
SOLDERING FOOTPRINT*
0.95
0.037
MILLIMETERS
MIN
MAX
2.85
3.15
1.35
1.65
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
0_
10 _
2.50
3.00
1.9
0.074
5
5
XXXAYWG
G
1
1
Analog
2.4
0.094
XXX = Specific Device Code
A
= Assembly Location
Y
= Year
W = Work Week
G
= Pb−Free Package
1.0
0.039
XXX MG
G
Discrete/Logic
XXX = Specific Device Code
M = Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DOCUMENT NUMBER:
DESCRIPTION:
98ARB18753C
TSOP−5
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative