LV5680NPVC
Linear Voltage Regulator, Multiple-Output,
System Power Supply IC,
for Automotive Infotainment System
Overview
The LV5680NPVC is a multi-power supply system IC that provides four
regulator outputs and two high side switches as well as a number of protection
functions including overcurrent protection, overvoltage protection and
overheat protection. It is an optimal power supply IC for car audio and car
entertainment systems and similar products.
Features
• Four regulator output systems
For microcontroller: 5.0V output voltage, 200mA maximum output
current
For CD drive: 8.0V output voltage, 1300mA maximum output current
For illumination: 8 to 12V output voltage (output can be set with external
resistors), 300mA maximum output current
For audio systems: 8 to 9V output voltage (output voltage can be set with
external resistors), 300mA maximum output current
• Two VCC-linked high side switch systems
EXT: 350mA maximum output current, 0.5V voltage difference between
input and output.
ANT: 300mA maximum output current, 0.5V voltage difference between
input and output.
• Two VDD 5V-linked high side switch systems
SW5V: 200mA maximum output current, 0.2V voltage difference between
input and output.
ACC (accessory voltage detection output): 100mA maximum output
current, 0.2V voltage
difference between input and
output.
• Overcurrent protection function
• Overvoltage protection function, typ 21V (excluding VDD 5V output)
• Overheat protection function, typ 175ºC
• On-chip accessory voltage detection circuit
• P-channel LDMOS used for power output block
(Warning) The protector functions only improve the IC’s tolerance and they do not
guarantee the safety of the IC if used under the conditions out of safety range or ratings.
Use of the IC such as use under over current protection range or thermal shutdown state
may degrade the IC’s reliability and eventually damage the IC.
www.onsemi.com
HZIP15J
GENERIC
MARKING DIAGRAM
XXXXXXXXXX
YMDDD
XXXXX = Specific Device Code
Y = Year
M = Month
DDD = Additional Traceability Data
ORDERING INFORMATION
Ordering Code:
LV5680NPVC-XH
Package
HZIP15J
(Pb-Free / Halogen Free)
Shipping (Qty / packing)
20 / Fan-Fold
Typical Applications
• Automotive infotainment
© Semiconductor Components Industries, LLC, 2017
February 2017- Rev. 1
1
Publication Order Number:
LV5680NPVC/D
LV5680NPVC
Specifications
Absolute Maximum Ratings at Ta = 25C
Parameter
(Note 1)
Conditions
Conditions
Ratings
Supply voltage
VCC max
Peak supply voltage
VCC peak
See below for the waveform applied.
Allowable Power dissipation
Pd max
Independent IC
Unit
36
Ta 25C
Al heat sink (Note 2)
With an infinity heat sink
V
50
V
1.5
W
5.6
W
32.5
W
150
C
Junction temperature
Tj max
Operating ambient temperature
Topr
-40 to +85
C
Storage temperature
Tstg
-55 to +150
C
1. Stresses exceeding those listed in the Maximum Rating table may damage the device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
2. When the Aluminum heat sink (50mm 50mm 1.5mm) is used
Recommended Operating Ranges at Ta = 25C
Parameter
Operating supply voltage 1
Operating supply voltage 2
(Note 3)
Conditions
Ratings
VDD output, SW output, ACC output
Unit
7.5 to 16
V
ILM output at 10V
12 to 16
V
ILM output at 8V
10 to 16
V
Operating supply voltage 3
Audio output at 9V
10 to 16
V
Operating supply voltage 4
CD output (CD output current = 1.3A)
CD output (CD output current 1A)
10.5 to 16
V
10 to 16
V
3. Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the
Recommended Operating Ranges limits may affect device reliability.
Electrical Characteristics at VCC = 14.4V, Ta = 25°C
Parameter
Current drain
Symbol
ICC
(Note 4,10)
Conditions
Ratings
min
typ
VDD no load, CTRL1/2 = L/L, ACC = 0V
Unit
max
400
800
A
0.5
V
CTRL1 Input
Low input voltage
VIL1
0
M1 input voltage
VIM11
0.8
1.1
1.4
V
M2 input voltage
VIM21
1.9
2.2
2.5
V
High input voltage
VIH1
2.9
3.3
5.5
V
Input impedance
RIH1
350
500
650
k
0.5
V
1.65
2.1
V
CTRL2 Input
Low input voltage
VIL2
0
M input voltage
VIM2
1.1
High input voltage
VIH2
2.5
3.3
5.5
V
Input impedance
RIH2
350
500
650
k
VDD 5V Output (Note 5)
The VDD 5V output supplies the output currents of SW 5V and ACC 5V.
Output voltage 1
VO1
IO1 = 200mA, IO7, IO8 = 0A
4.75
5.0
5.25
Output voltage 2
VO1’
IO1 = 200mA, IO7 = 200mA, IO8 = 100mA
4.75
5.0
5.25
Output total current
Ito1
VO1 4.75V, Ito1 = IO1+IO7+IO8
500
Line regulation
VOLN1
7.5V VCC 16V, IO1 = 200mA (Note 6)
30
90
mV
Load regulation
VOLD1
1mA IO1 200mA (Note 6)
70
150
mV
Dropout voltage 1
VDROP1
IO1 = 200mA (Note 6)
1.0
1.5
V
Dropout voltage 2
VDROP1’
IO1 = 100mA (Note 6)
0.7
1.05
V
Dropout voltage 3
VDROP1”
IO1+IO7+IO8 = 500mA
2.5
3.75
V
Ripple rejection
RREJ1
f = 120Hz, IO1 = 200mA (Note 6)
40
V
V
mA
50
dB
Continued on next page.
www.onsemi.com
2
LV5680NPVC
Continued from preceding page.
Parameter
Symbol
Conditions
Ratings
min
typ
Unit
max
CD Output ; CTRL2 = H
Output voltage
VO2
IO2 = 1000mA
Output current
IO2
VO2 7.6V
Line regulation
VOLN2
10.5V VCC 16V, IO2 = 1000mA
Load regulation
VOLD2
Dropout voltage 1
VDROP2
Dropout voltage 2
VDROP2’
IO2 = 500mA
Ripple rejection
RREJ2
f = 120Hz, IO2 = 1000mA
7.6
8.0
8.4
1300
V
mA
50
100
mV
10mA IO2 1000mA
100
200
mV
IO2 = 1000mA
1.0
1.5
V
0.5
0.75
V
40
50
dB
1.222
1.260
1.298
V
AUDIO (8-9V) Output ; CTRL2 = M
AUDIO_F pin voltage
VI 3
AUDIO_F pin inflow current
IIN3
1
A
AUDIO output voltage 1
VO3
IO3 = 200mA, R2 = 30k, R3 = 5.6k (Note 7)
7.65
8.0
8.35
V
AUDIO output voltage 2
VO3’
IO3 = 200mA, R2 = 27k, R3 = 4.7k (Note 7)
8.13
8.5
8.87
V
AUDIO output voltage 3
VO3”
IO3 = 200mA, R2 = 24k, R3 = 3.9k (Note 7)
8.6
9.0
9.4
AUDIO output current
IO3
Line regulation
VOLN3
10V VCC 16V, IO3 = 200mA
30
90
mV
Load regulation
VOLD3
1mA IO3 200mA
70
150
mV
Dropout voltage 1
VDROP3
IO3 = 200mA
0.3
0.45
V
Dropout voltage 2
VDROP3’
IO3 = 100mA
0.15
0.23
Ripple rejection
RREJ3
f = 120Hz, IO3 = 200mA
-1
300
V
mA
V
40
50
dB
1.222
1.260
1.298
V
11.4
12.0
12.6
V
ILM (8-12V) Output ; CTRL1 = M1
ILM_F pin voltage
VI4
ILM output voltage 1
VO4
IO4 = 200mA
ILM output voltage 2
VO4’
IO4 = 200mA, R1 = 270k (Note 8)
8.5
10.0
11.5
V
ILM output voltage 3
VO4”
IO4 = 200mA, R1 = 100k (Note 8)
6.8
8.0
9.2
V
ILM output current
IO4
R1 = 270k
300
Line regulation
VOLN4
12V VCC 16V, IO4 = 200mA, R1 = 270k
30
90
mV
Load regulation
VOLD4
1mA IO4 200mA
70
150
mV
Dropout voltage 1
VDROP4
IO4 = 200mA
0.7
1.05
V
0.35
0.53
mA
Dropout voltage 2
VDROP4’
IO4 = 100mA
Ripple rejection
RREJ4
f = 120Hz, IO4 = 200mA
Output voltage
VO5
IO5 = 350mA
Output current
IO5
VO5 VCC-1.0
Output voltage
VO6
IO6 = 300mA
Output current
IO6
VO6 VCC-1.0
VO7
IO7 = 1mA, IO1, IO8 = 0A (Note 9)
VO1-0.25
VO1
VO1-0.45
VO1-0.2
V
40
50
dB
VCC-1.0
VCC-0.5
V
Remoto (EXT) ; CTRL1 = M2
350
mA
ANT remoto ; CTRL1 = H
VCC-1.0
VCC-0.5
V
300
mA
SW 5V Output ; CTRL2 = M
Output voltage 1
Output voltage 2
VO7’
IO7 = 200mA, IO1, IO8 = 0A (Note 9)
Output current
IO7
VO7 4.55
V
V
200
mA
ACC Detection ; ACC Integration 5V output
ACC detection voltage
VTH8
2.8
3.0
3.2
Hysteresis width
VHIS8
0.2
0.3
0.4
V
V
Input impedance
ZI8
(Pull-down resistance internal)
42
60
78
k
ACC output voltage 1
VO8
IO8 = 0.5mA, IO1, IO7 = 0A (Note 9)
VO1-0.25
VO1
V
ACC output voltage 2
VO8’
IO8 = 100mA, IO1, IO7 = 0A (Note 9)
VO1-0.45
VO1-0.2
V
VO8 4.55
100
mA
4. Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the
Recommended Operating Ranges limits may affect device reliability.
ACC output voltage
IO8
www.onsemi.com
3
LV5680NPVC
5. The VDD 5V output also supplies the output currents of SW 5V and ACC 5V. Therefore, the current supply capability of the VDD 5V output and its other
electrical characteristics are affected by the output statuses of SW 5V and ACC 5V.
6. SW 5V and ACC 5V are not subject to a load.
7. When a component with a resistance accuracy of 1% is used
When a component with a resistance accuracy of 0.5% is used, VO3” is 8.67V 9.0V 9.33V
8. When a component with a resistance accuracy of 1% is used
The absolute accuracy of the internal resistance is 15%
9. Since the SW 5V and ACC 5V are output from VDD 5V through the SW, the voltage drops by an amount equivalent to the ON resistance of the SW.
10. The entire specification has been defined based on the tests performed under the conditions where Tj and Ta (=25C) are almost equal. There tests were
performed with pulse load to minimize the increase of junction temperature (Tj).
• Allowable power dissipation derating curve
Pd max -- Ta
Allowable power dissipation, Pd max -- W
8
Aluminum heat sink mounting conditions
tightening torque : 39N⋅cm, using silicone grease
7
Aluminum heat sink (50 × 50 × 1.5mm3) when using
6
5.6
5
4
3
2
Independent IC
1.5
1
0
0
20
40
60
80
100
120
140 150 160
Ambient temperature, Ta -- °C
• Waveform applied during surge test
50V
90%
10%
16V
5msec
100msec
www.onsemi.com
4
LV5680NPVC
Package Dimensions
unit : mm
HZIP15J
CASE 945AC
ISSUE A
SOLDERING FOOTPRINT*
Through Hole Area
(Unit: mm)
Package name
HZIP15J
2.54
1.2
2.54
(1.91)
2.54
2.54
NOTE: The measurements are not to guarantee but for reference only.
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
5
LV5680NPVC
Block Diagram
+B
VCC
+
C1
7
C2
EXT
out
15
ANT
out
Over
Voltage
Protection
Start
up
+
Vref
CTRL1
8
(four-value control)
CTRL2
6
(three-value control)
+
C3
D2
ANT Remote (VCC-0.5V)
D3 300mA
14
+
D4
C4
1
2
+
Remote EXT (VCC-0.5V)
D1 350mA
5
4
OUTPUT
ILM output (8V to 12V)
300mA
+
R1 C6
C7
ILM_F
AUDIO output (8V to 9V)
300mA
+
R2 C9
C10
AUDIO_F
R3
Control
+
3
+
Thermal
Shut Down
CD output (8V)
1300mA
+
C11
C12
VDD output (5.0V)
200mA
12
+
C13
C14
GND
9
13
ACC
SW output (5V)
200mA
10
Output Current Limit Circuit
www.onsemi.com
6
11
ACC output (5V)
100mA
LV5680NPVC
Pin Function
Pin No.
1
Pin name
ILM
Description
Equivalent Circuit
ILM output pin
VCC
7
ON when CTRL1 = M1, M2, H
12.0V/300mA
1
2
ILM_F
59.67kΩ
ILM output voltage adjustment pin
2
7kΩ
3
CD
CD output pin
ON when CTRL2 = M, H
9
GND
7
VCC
8.0V/1.3A
3
214kΩ
40kΩ
4
AUDIO_F
AUIDO output voltage adjustment pin
9
GND
7
VCC
5
5
AUDIO
AUDIO output pin
ON when CTRL2 = M, H
4
9
6
CTRL2
CTRL2 input pin
three-value input
GND
VCC
7
6
7
VCC
500kΩ
9
GND
Supply terminal
Continued on next page.
www.onsemi.com
7
LV5680NPVC
Continued from preceding page.
Pin No.
8
Pin name
CTRL1
Description
CTRL1 input pin
four-value input
Equivalent Circuit
VCC
7
8
500kΩ
9
9
GND
GND pin
10
ACC
Accessory input
GND
VCC
7
10
45kΩ
15kΩ
9
11
ACC5V
Accessory detection output
ON when ACC 3V
12
VDD5V
VDD5V output pin
5.0V/200mA
GND
VCC
7
12
371kΩ
11
13
SW5V
SW5V output pin
13
ON when CTRL2 = M, H
50kΩ 50kΩ
9
14
ANT
ANT output pin
GND
7
ON when CTRL1 = H
125kΩ
VCC
VCC-0.5V/300mA
14
9
GND
Continued on next page
www.onsemi.com
8
LV5680NPVC
Continued from preceding page.
Pin No.
15
Pin name
EXT
Description
Equivalent Circuit
EXT output pin
7
ON when CTRL1 = M2, H
VCC
VCC-0.5V/350mA
15
9
www.onsemi.com
9
GND
LV5680NPVC
CTRL Pin Output Truth Table
CTRL1
ANT
EXT
ILM
CTRL2
CD
AUDIO
SW5
OFF
L
OFF
OFF
OFF
L
OFF
OFF
M1
OFF
OFF
ON
M
OFF
ON
ON
M2
OFF
ON
ON
H
ON
ON
ON
H
ON
ON
ON
Timing Chart
21V
VCC
(Pin 7)
VDD5V output
(Pin 12)
CTRL1 input
(Pin 8)
CTRL2 input
(Pin 6)
CD output
(Pin 3)
AUDIO output
(Pin 5)
ILM output
(Pin 1)
EXT output
(Pin 15)
ANT output
(Pin 14)
SW5V output
(Pin 13)
ACC input
(Pin 10)
3.0V
2.7V
ACC output
(Pin 11)
www.onsemi.com
10
LV5680NPVC
R1
R3
C9 + C10
ILM
12
11
CD
EXT
ANT
SW5V
VDD5V
CTRL1
ACC
10
9
14
13
R2
15
+
C4
CTRL2
C5 + C6
8
7
ACC5V
6
5
GND
4
3
VCC
CTRL2
AUDIO
2
1
CD
ILM
ILM_F
AUDIO_F
Recommended Operation Circuit
C7 + C8
AUDIO
CTRL1
ACC ACC5V
C1 + C2
SW5V
C11 + C12
VCC
VDD5V
+
C3
D3
D1
D4
D2
ANT
EXT
Peripheral parts list
Name of part
Description
Recommended value
Remarks
C1
Power supply bypass capacitor
100F or more
These capacitors must be placed near the
C2
Oscillation prevention capacitor
0.22F or more
VCC and GND pins.
C3
EXT output stabilization capacitor
2.2F or more
C4
ANT output stabilization capacitor
2.2F or more
C5, C7, C9, C11
Output stabilization capacitor
4.7F or more
Electrolytic capacitor *
C6, C8, C10, C12
Output stabilization capacitor
0.22F or more
Ceramic capacitor *
R1
Resistor for ILM voltage adjustment
ILM output voltage
A resistor with resistance accuracy as low
R1:without = 12.0V
as less than 1% must be used.
:270k = 10.0V
:100k = 8.0V
AUDIO output voltage
R2, R3
R2/R3:30k/5.6k = 8.0V
Resistor for AUDIO voltage setting
:27k/4.7k = 8.5V
A resistor with resistance accuracy as low
as less than 1% must be used.
:24k/3.9k = 9.0V
D1, D2, D3, D4
Diode for internal device breakdown protection
* : In order to stabilize the regulator outputs, it is recommended that the electrolytic capacitor and ceramic capacitor be connected in parallel.
Furthermore, the values listed above do not guarantee stabilization during the overcurrent protection operations of the regulator, so oscillation may occur during
an overcurrent protection operation.
www.onsemi.com
11
LV5680NPVC
• ILM output voltage setting method
Formula for ILM voltage calculation
Z1 R2 //R3
1
ILM
R2 59.67kΩ
ILM
R3
Z1=R2/R3
1.26V
2
ILM_F
Z1
R2 R3
R2 R3
1.26[V ]
Z1 1.26[V ]
R1
ILM 1.26 R1
1.26
R3
R2 Z 1
R2 Z 1
Example : ILM = 9V setting method
R1 7kΩ
Z1
The ILM_F voltage is determined by the
internal band gap voltage of the IC (typ = 1.26V).
R3
9V 1.26V 7kΩ 43kΩ
1.26V
59.67 k 43k
153.9k 150k
59.67k 43k
When R3 = 150k, the ILM output voltage will be as follows:
59.67 kΩ 150kΩ
Z1
42.69kΩ
59.67 kΩ 150kΩ
ILM
1.26V
42.69kΩ 1.26V 8.94V
7 kΩ
• AUDIO output voltage setting method
Formula for AUDIO voltage calculation
AUDIO
5
1.26[V ]
R1 1.26[V ]
R2
R1 AUDIO 1.26
1.26
R2
AUDIO
R1
1.26V
4
The circuit must be designed in such a way that the R1:R2 ratio
satisfies the formula given above for the AUDIO voltage that has
been set.
AUDIO_F
R2
Example : AUDIO = 8.5V setting method
The AUDIO_F voltage is determined by the
internal band gap voltage of the IC (typ = 1.26V).
R1 8.5 1.26
5.75
R2
1.26
R1 27 kΩ
5.74
R2 4.7 kΩ
AUDIO 1.26V 5.74 1.26V 8.49V
Note : In the above, the typical values are given in all instances for the values used and, as such, they will vary due to the
effects of production-related variations of the IC and external resistors.
www.onsemi.com
12
LV5680NPVC
• CTRL1 Application Circuit Example
(1) 3.3V input: R1 = 4.7k, R2 = 10k
A
B
R1
R2
CTRL1
500kΩ
A
B
CTRL1
0V
0V
0V
0V
3.3V
1.05V
3.3V
0V
2.23V
3.3V
3.3V
3.20V
• CTRL2 Application Circuit Example
(1) 3.3V input: R3 = R4 = 4.7k
C
D
R3
R4
CTRL2
500kΩ
A
B
0V
0V
CTRL2
0V
0V
3.3V
1.61V
3.3V
0V
1.61V
3.3V
3.3V
3.29V
www.onsemi.com
13
LV5680NPVC
HZIP15J Heat sink attachment
Heat sinks are used to lower the semiconductor device junction temperature by leading the head generated by the device to
the outer environment and dissipating that heat.
a.Unless otherwise specified, for power ICs with tabs and power ICs with attached heat sinks, solder must not be applied to
the heat sink or tabs.
b. Heat sink attachment
· Use flat-head screws to attach heat sinks.
· Use also washer to protect the package.
· Use tightening torques in the ranges 39-59Ncm(4-6kgcm) .
· If tapping screws are used, do not use screws with a diameter larger than the
holes in the semiconductor device itself.
· Do not make gap, dust, or other contaminants to get between the
semiconductor device and the tab or heat sink.
· Take care a position of via hole .
· Do not allow dirt, dust, or other contaminants to get between the
semiconductor device and the tab or heat sink.
· Verify that there are no press burrs or screw-hole burrs on the heat sink.
· Warping in heat sinks and printed circuit boards must be no more than 0.05
mm between screw holes, for either concave or convex warping.
· Twisting must be limited to under 0.05 mm.
· Heat sink and semiconductor device are mounted in parallel.
Take care of electric or compressed air drivers
· The speed of these torque wrenches should never exceed 700 rpm, and
should typically be about 400 rpm.
Binding head
machine screw
Countersunk head
mashine screw
Heat sink
gap
Via hole
c.Silicone grease
· Spread the silicone grease evenly when mounting heat sinks.
· Our company recommends YG-6260 (Momentive Performance Materials Japan LLC)
d. Mount
· First mount the heat sink on the semiconductor device, and then mount that assembly on the printed circuit board.
· When attaching a heat sink after mounting a semiconductor device into the printed circuit board, when tightening up a
heat sink with the screw, the mechanical stress which is impossible to the semiconductor device and the pin doesn't
hang.
e.When mounting the semiconductor device to the heat sink using jigs, etc.,
· Take care not to allow the device to ride onto the jig or positioning dowel.
· Design the jig so that no unreasonable mechanical stress is not applied to the semiconductor device.
f. Heat sink screw holes
· Be sure that chamfering and shear drop of heat sinks must not be larger than the diameter of screw head used.
· When using nuts, do not make the heat sink hole diameters larger than the diameter of the head of the screws used. A
hole diameter about 15% larger than the diameter of the screw is desirable.
· When tap screws are used, be sure that the diameter of the holes in the heat sink are not too small. A diameter about
15% smaller than the diameter of the screw is desirable.
g. There is a method to mount the semiconductor device to the heat sink by using a spring band. But this method is not
recommended because of possible displacement due to fluctuation of the spring force with time or vibration.
www.onsemi.com
14
LV5680NPVC
Caution for implementing LV5680P to a system board
The package of LV5680P is HZIP15J which has some metal exposures other than connection pins and heatsink as shown in the diagram
below. The electrical potentials of (2) and (3) are the same as those of pin 15 and pin 1, respectively. (2) (=pin 15) is the VCC pin and (3)
(=pin 1) is the ILM (regulator) output pin. When you implement the IC to the set board, make sure that the bolts and the heatsink are out of
touch from (2) and (3). If the metal exposures touch the bolts which has the same electrical potential with GND, GND short occurs in ILM
output and VCC. The exposures of (1) are connected to heatsink which has the same electrical potential with substrate of the IC chip
(GND). Therefore, (1) and GND electrical potential of the set board can connect each other.
• HZIP15J outline
Heat-sink
1 Same potential
2 15PIN
Same potential
1PIN
3 Same potential
Heat-sink
1 Same potential
Heat-sink side
1
Heat-sink
Same potential
:Metal exposure
Heat-sink side
:Metal exposure
• Frame diagram (LV5680NPVC) *In the system power supply other than LV5680NPVC, pin assignment may differ.
Metal exposure 1
Metal exposure 3
Metal exposure 2
LV5680NPVC
Metal exposure 1
Metal exposure 1
Metal exposure 1
15PIN
1PIN
www.onsemi.com
15
LV5680NPVC
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries
in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other
intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON
Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or
use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is
responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or
standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters,
including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its
patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support
systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for
implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall
indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an
Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
www.onsemi.com
16
工商网监
湘ICP备2023018690号
