MC100E431FNR2

5 V ECL 3‐Bit Differential Flip‐Flop MC10E431 Description The MC10E431 is a 3-bit flip-flop with differential clock, data input and data output. The asynchronous Set and Reset controls are edge-triggered rather than level controlled. This allows the user to rapidly set or reset the flip-flop and then continue clocking at the next clock edge, without the necessity of de-asserting the set/reset signal (as would be the case with a level controlled set/reset). The E431 is also designed with larger internal swings, an approach intended to minimize the time spent crossing the threshold region and thus reduce the metastability susceptibility window. The differential input structures are clamped so that the inputs of unused registers can be left open without upsetting the bias network of the device. The clamping action will assert the D and the CLK sides of the inputs. Because of the edge triggered flip-flop nature of the device simultaneously opening both the clock and data inputs will result in an output which reaches an unidentified but valid state. Note that the input clamps only operate when both inputs fall to 2.5 V below VCC. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. Features • • • • • • • • • • • • Edge-Triggered Asynchronous Set and Reset Differential D, CLK and Q; VBB Reference Available 1100 MHz Min. Toggle Frequency PECL Mode Operating Range: VCC = 4.2 V to 5.7 V with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = −4.2 V to −5.7 V Internal Input 50 kW Pulldown Resistors ESD Protection: ♦ > 2 kV Human Body Model ♦ > 200 V Machine Model ♦ > 2 kV Charged Device Model Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test Moisture Sensitivity: Level 3 (Pb-Free) (For Additional Information, see Application Note AND8003/D) Flammability Rating: UL 94 V−0 @ 0.125 in, Oxygen Index: 28 to 34 Transistor Count = 348 Devices These Devices are Pb-Free, Halogen Free and are RoHS Compliant © Semiconductor Components Industries, LLC, 2016 April, 2021 − Rev. 12 1 www.onsemi.com PLCC−28 FN SUFFIX CASE 776−02 MARKING DIAGRAM* 1 28 MC10E431FNG AWLYYWW A WL YY WW G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION Device Package Shipping† MC10E431FNG PLCC−28 (Pb-Free) 37 Units / Tube MC10E431FNR2G PLCC−28 (Pb-Free) 500 Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Publication Order Number: MC10E431/D MC10E431 VBB CLK2 CLK2 25 24 23 D2 D2 R2 S2 22 21 20 19 Table 1. PIN DESCRIPTION PIN FUNCTION CLK1 26 18 Q2 D[0:2], D[0:2] ECL Differential Data Inputs CLK1 27 17 Q2 CLK[0:2], CLK[0:2] ECL Differential Clock R1 16 VCC S[0:2] ECL Edge Triggered Set Inputs 28 R[0:2] ECL Edge Triggered Reset Input 1 15 Q1 Q[0:2], Q[0:2] ECL Differential Data Outputs Q1 VBB Reference Voltage Output VCC, VCCO Positive Supply VEE Negative Supply VEE MC10E431 S1 2 14 D1 3 13 Q0 D1 4 12 Q0 5 6 7 CLK0 CLK0 D0 8 9 10 D0 R0 S0 11 VCCO * All VCC and VCCO pins are tied together on the die. Warning: All VCC, VCCO, and VEE pins must be externally connected to Power Supply to guarantee proper operation. Figure 1. Pinout: PLCC-28 (Top View) S0 D0 D0 D CLK0 CLK0 R0 S1 D1 D1 S R D CLK1 CLK1 S R Q Q0 Q Q0 Q Q1 Q Q1 Q Q2 Q Q2 Table 2. FUNCTION TABLE Dn CLKn Rn Sn L Z L L L H Z L L H X X Z L L X X L Z H Z = Low to high transition X = Don’t Care R1 S2 D2 D2 D CLK2 CLK2 S R R2 VBB Figure 2. Logic Diagram www.onsemi.com 2 Qn MC10E431 Table 3. MAXIMUM RATINGS Symbol Parameter Condition 1 VCC PECL Mode Power Supply VEE = 0 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V Iout Output Current Continuous Surge IBB VBB Sink/Source TA Operating Temperature Range Tstg Storage Temperature Range qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm qJC Thermal Resistance (Junction-to-Case) Standard Board Tsol Wave Solder (Pb-Free) Condition 2 Rating Unit 8 V 6 −6 V 50 100 mA ±0.5 mA 0 to +85 °C −65 to +150 °C PLCC−28 PLCC−28 63.5 43.5 °C/W PLCC−28 22 to 26 °C/W 265 °C VI v VCC VI w VEE Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Table 4. 10E SERIES PECL DC CHARACTERISTICS (VCCx= 5.0 V; VEE= 0.0 V (Note 1)) 0°C Symbol Characteristic Min 25°C Typ Max 110 132 Min 85°C Typ Max 110 132 Min Typ Max Unit 110 132 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 2) 3980 4070 4160 4020 4105 4190 4090 4185 4280 mV VOL Output LOW Voltage (Note 2) 3050 3210 3370 3050 3210 3370 3050 3227 3405 mV VIH Input HIGH Voltage (Single-Ended) 3830 3995 4160 3870 4030 4190 3940 4110 4280 mV VIL Input LOW Voltage (Single-Ended) 3050 3285 3520 3050 3285 3520 3050 3302 3555 mV VBB Output Voltage Reference 3.62 3.74 3.65 3.75 3.69 3.81 V Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) 2.7 5.0 2.7 5.0 2.7 5.0 V 150 mA VIHCMR IIH Input HIGH Current IIL Input LOW Current 150 0.5 0.3 150 0.5 0.25 0.3 0.2 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. 1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V. 2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. 3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. www.onsemi.com 3 MC10E431 Table 5. 10E SERIES NECL DC CHARACTERISTICS (VCCx= 0.0 V; VEE= −5.0 V (Note 1) 0°C Symbol Characteristic Min 25°C Typ Max 110 132 Min 85°C Typ Max 110 132 Min Typ Max Unit 110 132 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 2) −1020 −930 −840 −980 −895 −810 −910 −815 −720 mV VOL Output LOW Voltage (Note 2) −1950 −1790 −1630 −1950 −1790 −1630 −1950 −1773 −1595 mV VIH Input HIGH Voltage (Single-Ended) −1170 −1005 −840 −1130 −970 −810 −1060 −890 −720 mV VIL Input LOW Voltage (Single-Ended) −1950 −1715 −1480 −1950 −1715 −1480 −1950 −1698 −1445 mV VBB Output Voltage Reference −1.38 −1.27 −1.35 −1.25 −1.31 −1.19 V Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) −2.3 0.0 −2.3 0.0 −2.3 0.0 V 150 mA VIHCMR IIH Input HIGH Current IIL Input LOW Current 150 0.5 0.3 150 0.5 0.065 0.3 0.2 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. 1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V. 2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. 3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. Table 6. AC CHARACTERISTICS (VCCx= 5.0 V; VEE= 0.0 V or VCCx= 0.0 V; VEE= −5.0 V (Note 1)) −40°C Min Characteristic Symbol Typ fMAX Maximum Toggle Frequency tPLH tPHL Propagation Delay to Output CLK R S 550 500 500 700 725 725 tS Setup Time D R (Note 2) S (Note 2) 250 1100 1100 tH Hold Time D 250 CLK 400 tPW Minimum Pulse Width tskew 25°C Max Min Typ 85°C Max Min Typ Max 1.1 850 975 975 550 550 550 700 725 725 0 700 700 200 1000 1000 0 200 GHz 850 925 925 550 550 550 700 725 725 0 700 700 200 1000 1000 0 700 700 0 200 0 400 Within-Device Skew (Note 3) 50 tJITTER Random Clock Jitter (RMS)