MC100EP16VTMNR4G

MC100EP16VT 3.3V / 5VECL Differential Receiver/Driver with Variable Output Swing and Internal Input Termination The MC100EP16VT is a differential receiver functionally equivalent to the 100EP16 with input pins controlling the amplitude of the outputs (pin 1) and providing an internal termination network (pin 4). The VCTRL input pin controls the output amplitude of the EP16VT and is referenced to VCC. (See Figure 4.) The operational range of the VCTRL input is from
VBB (a supply at VCC–1.42 V, maximum output amplitude) to VCC (minimum output amplitude). VBB is an externally supplied voltage equal to VCC–1.42 V (See Figures 2 and 3). A variable resistor between VCC and VBB, with the wiper driving VCTRL, can control the output amplitude. Typical application circuits and a VCTRL Voltage vs. Output Amplitude graph are described in this data sheet. When left open, the VCTRL pin will be internally pulled down to VEE and operate as a standard EP16, with 100% output amplitude. The VTT input pin offers an internal termination network for a 50 ohm line impedance environment, shown in Figure 1. For further reference, see Application Note AND8020, Termination of ECL Logic Devices. Input considerations are required for D and D under no signal conditions to prevent instability. Special considerations are required for differential inputs under No Signal conditions to prevent instability. • • • • • http://onsemi.com MARKING DIAGRAMS* 8 SO–8 D SUFFIX CASE 751 8 1 KEP63 ALYW 1 8 TSSOP–8 DT SUFFIX CASE 948R 8 1 KP63 ALYW 1 K A L Y W = MC100 = Assembly Location = Wafer Lot = Year = Work Week *For additional information, see Application Note AND8002/D 220 ps Propagation Delay Maximum Frequency > 4 GHz Typical (See Graph) The 100 Series Contains Temperature Compensation PECL Mode Operating Range: VCC = 3.0 V to 5.5 V with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = –3.0 V to –5.5 V Open Input Default State ORDERING INFORMATION • • 50
Internal Termination Resistor Device Package Shipping MC100EP16VTD SO–8 98 Units/Rail MC100EP16VTDR2 SO–8 2500 Tape & Reel MC100EP16VTDT TSSOP–8 100 Units/Rail MC100EP16VTDTR2 TSSOP–8 2500 Tape & Reel  Semiconductor Components Industries, LLC, 2001 April, 2001 – Rev. 1 1 Publication Order Number: MC100EP16VT/D MC100EP16VT VCTRL D 1 8 2 7 PIN DESCRIPTION VCC Q 50
D 3 6 Q 50
VTT 4 5 VEE PIN FUNCTION D, D ECL Data Inputs Q, Q ECL Data Outputs VCTRL* Output Swing Control VTT Termination Supply VCC Positive Supply VEE Negative Supply * Pin will default LOW when left open. Figure 1. 8–Lead Pinout (Top View) and Logic Diagram ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 k
Internal Input Pullup Resistor ESD Protection N/A Human Body Model Machine Model Charged Device Model > 4 kV > 200 V > 2 kV Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1.) Level 1 Flammability Rating Oxygen Index UL–94 code V–0 A 1/8” 28 to 34 Transistor Count 140 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. MAXIMUM RATINGS (Note 2.) Symbol Parameter Condition 1 Condition 2 Rating Units VCC PECL Mode Power Supply VEE = 0 V 6 V VEE NECL Mode Power Supply VCC = 0 V –6 V VI PECL Mode In Input ut Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 –6 V V Iout Output Current Continuous Surge 50 100 mA mA TA Operating Temperature Range –40 to +85 °C Tstg Storage Temperature Range –65 to +150 °C θJA Thermal Resistance (Junction to Ambient) 0 LFPM 500 LFPM 8 SOIC 8 SOIC 190 130 °C/W °C/W θJC Thermal Resistance (Junction to Case) std bd 8 SOIC 41 to 44 °C/W θJA Thermal Resistance (Junction to Ambient) 0 LFPM 500 LFPM 8 TSSOP 8 TSSOP 185 140 °C/W °C/W θJC Thermal Resistance (Junction to Case) std bd 8 TSSOP 41 to 44 ± 5% °C/W Tsol Wave Solder VBB VCTRL = VCC (Min Swing) 25°C 1490 See Fig.2 2105 2230 1520 See Fig.2 2355 2095 2220 1520 1605 See Fig.2 2345 2065 2190 2315 VIH D, D Input HIGH Voltage (Single Ended) 2075 2420 2075 2420 2075 2420 mV VIL D, D Input LOW Voltage (Single Ended) 1490 1675 1490 1675 1490 1675 mV VCTRL Input Voltage (VCTRL) VEE VCC VEE VCC VEE VCC mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 5.) 2.0 2.9 2.0 2.9 2.0 2.9 V IIH Input HIGH Current (VTT Open) 150 µA IIL Input LOW Current (VTT Open) 150 –150 150 –150 µA –150 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 3. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to –2.2 V. 4. All loading with 50 ohms to VCC–2.0 volts. VOH does not change with VCTRL. VOL changes with VCTRL. VCTRL is referenced to VCC. 5. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 6.) –40°C Symbol Characteristic IEE Power Supply Current VOH Output HIGH Voltage (Note 7.) VCC > VCTRL > VEE VOL Output LOW Voltage (Max Swing) (Note 7.) VCTRL
VBB 85°C Min Typ Max Min Typ Max Min Typ Max Unit 30 36 42 31 38 44 32 40 48 mA 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV 3055 3190 3305 3055 3220 3305 3055 3220 3305 mV VCC  VCTRL > VBB VCTRL = VCC (Min Swing) 25°C See Fig.2 3805 3930 See Fig.2 4055 3795 3920 See Fig.2 4045 3765 3890 4015 VIH D, D Input HIGH Voltage (Single Ended) 3775 4120 3775 4120 3775 4120 mV VIL D, D Input LOW Voltage (Single Ended) 3190 3375 3190 3375 3190 3375 mV VCTRL Input Voltage (VCTRL) VEE VCC VEE VCC VEE VCC mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 8.) 2.0 4.6 2.0 4.6 2.0 4.6 V IIH Input HIGH Current (VTT Open) 150 µA IIL Input LOW Current (VTT Open) 150 –150 150 –150 –150 µA NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 6. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to –0.5 V. 7. All loading with 50 ohms to VCC–2.0 volts. VOH does not change with VCTRL. VOL changes with VCTRL. VCTRL is referenced to VCC. 8. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 3 MC100EP16VT DC CHARACTERISTICS, NECL VCC = 0 V; VEE = –5.5 V to –3.0 V (Note 9.) –40°C Symbol Characteristic IEE Power Supply Current VOH Output HIGH Voltage (Note 10.) VCC > VCTRL > VEE VOL Output LOW Voltage (Max Swing) (Note 10.) VCTRL
VBB 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 30 36 42 31 38 44 32 40 48 mA –1145 –1020 –895 –1145 –1020 –895 –1145 –1020 –895 mV –1945 –1810 –1695 –1945 –1780 –1695 –1945 –1780 –1695 mV VCC  VCTRL > VBB See Fig.2 VCTRL = VCC (Min Swing) –1195 VIH D, D Input HIGH Voltage (Single Ended) VIL D, D Input LOW Voltage (Single Ended) VCTRL Input Voltage (VCTRL) VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 11.) IIH Input HIGH Current (VTT Open) IIL Input LOW Current (VTT Open) See Fig.2 –1070 –945 –1205 –1225 –880 –1810 –1625 VEE VCC VEE+2.0 –955 –1235 –1225 –880 –1225 –880 mV –1810 –1625 –1810 –1625 mV VEE VCC VEE VCC mV –0.4 V 150 µA –0.4 –1080 See Fig.2 VEE+2.0 –0.4 150 –1110 VEE+2.0 150 –150 –150 –985 µA –150 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 9. Input and output parameters vary 1:1 with VCC. 10. All loading with 50 ohms to VCC–2.0 volts. VOH does not change with VCTRL. VOL changes with VCTRL. VCTRL is referenced to VCC. 11. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. AC CHARACTERISTICS VCC = 0 V; VEE = –3.0 V to –5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 12.) –40°C Symbol Characteristic Min fmax Maximum Toggle Frequency (See Figure 8. Fmax/JITTER) tPLH, tPHL Propagation Delay to Output Differential Max Swing Min Swing tSKEW Typ 25°C Max Min >4 85°C Max Min >4 Typ Max >4 Unit GHz ps 300 250 350 300 Duty Cycle Skew (Note 13.) 5.0 tJITTER Cycle–to–Cycle Jitter (See Figure 8. Fmax/JITTER) VPP Input Voltage Swing (Differential) (Note 14.) tr, tf Output Rise/Fall Times (20% – 80%) Max Swing Q Min Swing Typ 250 200 250 200 300 250 350 300 20 5.0 0.2