MC100EP90DTG

MC10EP90, MC100EP90 Translator, Triple ECL Input to LVPECL / PECL Output Description The MC10/100EP90 is a TRIPLE ECL TO LVPECL/PECL translator. The device receives differential LVECL or ECL signals and translates them to differential LVPECL or PECL output signals. A VBB output is provided for interfacing with Single−Ended LVECL or ECL signals at the input. If a Single−Ended input is to be used the VBB output should be connected to the D input. The active signal would then drive the D input. When used the VBB output should be bypassed to ground by a 0.01 mF capacitor. The VBB output is designed to act as the switching reference for the EP90 under Single−Ended input switching conditions, as a result this pin can only source/sink up to 0.5 mA of current. To accomplish the level translation the EP90 requires three power rails. The VCC supply should be connected to the positive supply, and the VEE connected to the negative supply. The 100 Series contains temperature compensation. http://onsemi.com TSSOP−20 DT SUFFIX CASE 948E MARKING DIAGRAM* 20 xxxx EP90 ALYWG G Features • 260 ps Typical Propagation Delay • Maximum Frequency > 3 GHz Typical • Voltage Supplies VCC = 3.0 V to 5.5 V, VEE = −3.0 V to −5.5 V, • • • • • • GND = 0 V Open Input Default State Safety Clamp on Inputs Fully Differential Design Q Output Will Default LOW with Inputs Open or at VEE VBB Output These are Pb−Free Devices* 1 xxxx = MC10 or 100 A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2014 May, 2014 − Rev. 7 1 Publication Order Number: MC10EP90/D MC10EP90, MC100EP90 VCC Q0 Q0 GND Q1 Q1 GND Q2 Q2 VCC 20 19 18 17 16 15 14 13 12 11 Table 1. PIN DESCRIPTION PIN FUNCTION Q(0:2), Q(0:2) Differential LVPECL or PECL Outputs D(0:2)*, D(0:2)* Differential LVECL or ECL Inputs LVPECL/ PECL LVPECL/ PECL ECL LVPECL/ PECL ECL ECL VCC Positive Supply GND Ground VEE Negative Supply VBB Output Reference Supply * Pins will default LOW when left open. Table 2. FUNCTION TABLE 1 2 3 4 5 6 7 8 9 10 VCC D0 D0 VBB D1 D1 VBB D2 D2 VEE Warning: All VCC, VEE and GND pins must be externally connected to Power Supply to guarantee proper operation. Figure 1. TSSOP−20 (Top View) and Logic Diagram Function VCC 5V 0V −5 V −5V ECL to 3.3V PECL 3.3 V 0V −5 V −3.3V ECL to 5V PECL 5V 0V −3.3 V −3.3V ECL to 3.3V PECL 3.3 V 0V −3.3 V Characteristics Value Internal Input Pulldown Resistor 75 kW Internal Input Pullup Resistor N/A Human Body Model Machine Model Charged Device Model Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) TSSOP−20 Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 2 kV > 200 V > 2 kV Pb Pkg Pb−Free Pkg Level 1 Level 1 UL 94 V−0 @ 0.125 in 350 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, refer to Application Note AND8003/D. http://onsemi.com 2 VEE −5V ECL to 5V PECL Table 3. ATTRIBUTES ESD Protection GND MC10EP90, MC100EP90 Table 4. MAXIMUM RATINGS Rating Unit VCC Symbol PECL Mode Power Supply Parameter GND = 0 V Condition 1 6 V VEE NECL Mode Power Supply GND = 0 V −6 V VI PECL Mode Input Voltage NECL Mode Input Voltage GND = 0 V GND = 0 V 6 −6 V V Iout Output Current Continuous Surge 50 100 mA mA IBB VBB Sink/Source ± 0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm TSSOP−20 TSSOP−20 140 100 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board TSSOP−20 23 to 41 °C/W Tsol Wave Solder 3 240 Within Device Skew Q, Q Device to Device Skew (Note 15) Typ 230 300 370 ps 5.0 20 ps 80 140 0.2