MC74VHC1G03DFT2G

DATA SHEET www.onsemi.com Single 2-Input NOR Gate with Open Drain Output MARKING DIAGRAMS MC74VHC1G03, MC74VHC1GT03 The MC74VHC1G03 / MC74VHC1GT03 is a 2−input NOR Gate with an open drain output in tiny footprint packages. The input structures provide protection when voltages up to 5.5 V are applied, regardless of the supply voltage. This allows the device to be used to interface 5 V circuits to 3 V circuits. Some output structures also provide protection when VCC = 0 V and when the output voltage exceeds VCC. These input and output structures help prevent device destruction caused by supply voltage − input/output voltage mismatch, battery backup, hot insertion, etc. SC−88A DF SUFFIX CASE 419A XX MG G SC−74A DBV SUFFIX CASE 318BQ XXX MG G 5 TSOP−5 DT SUFFIX CASE 483 5 1 1 Features • • • • • • • • • Designed for 2.0 V to 5.5 V VCC Operation 3.5 ns tPD at 5 V (typ) Inputs/Outputs Over−Voltage Tolerant up to 5.5 V IOFF Supports Partial Power Down Protection Source/Sink 8 mA at 3.0 V Available in SC−88A, SC−74A, TSOP−5, SOT−553, SOT−953 and UDFN6 Packages Chip Complexity < 100 FETs NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant A ≥1 B Y SOT−553 XV5 SUFFIX CASE 463B SOT−953 P5 SUFFIX CASE 527AE XX MG G XM 1 UDFN6 1.45 x 1.0 CASE 517AQ 1 UDFN6 1.0 x 1.0 CASE 517BX XX M G Figure 1. Logic Symbol XX MG G XM XM 1 = Specific Device Code = Date Code* = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. ORDERING INFORMATION See detailed ordering, marking and shipping information in the package dimensions section on page 7 of this data sheet. © Semiconductor Components Industries, LLC, 2007 April, 2022 − Rev. 17 1 Publication Order Number: MC74VHC1G03/D MC74VHC1G03, MC74VHC1GT03 B VCC 1 5 OVT A VCC A 5 1 GND GND 4 3 6 VCC OVT A 2 5 NC GND 3 4 Y Y B Y 1 OVT 2 2 B 4 3 SOT−953 (SC−88A/SOT−553/ TSOP−5/ SC−74A) UDFN6 Figure 2. Pinout (Top View) PIN ASSIGNMENT (SC−88A/SOT−553/ TSOP−5/SC−74A) PIN ASSIGNMENT (SOT−953) PIN ASSIGNMENT (UDFN) Pin Function Pin Function Pin Function 1 B 1 A 1 B 2 A 2 GND 2 A 3 GND 3 B 3 GND 4 Y 4 Y 4 Y 5 VCC 5 VCC 5 NC 6 VCC FUNCTION TABLE Input Output A B Y L L Z L H L H L L H H L www.onsemi.com 2 MC74VHC1G03, MC74VHC1GT03 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage TSOP−5, SC−88A (NLV) SC−74A, SC−88A, UDFN6, SOT−553, SOT−953 −0.5 to +7.0 −0.5 to +6.5 V VIN DC Input Voltage TSOP−5, SC−88A (NLV) SC−74A, SC−88A, UDFN6, SOT−553, SOT−953 −0.5 to +7.0 −0.5 to +6.5 V −0.5 to VCC + 0.5 V VOUT Characteristics DC Output Voltage (NLV) 1Gxx 1GTxx Active−Mode (High or Low State) Tri−State Mode (Note 1) Power−Down Mode (VCC = 0 V) −0.5 to VCC + 0.5 −0.5 to +7.0 −0.5 to +7.0 Active−Mode (High or Low State) Tri−State Mode (Note 1) Power−Down Mode (VCC = 0 V) −0.5 to VCC + 0.5 −0.5 to +6.5 −0.5 to +6.5 V VIN < GND −20 mA VOUT > VCC, VOUT < GND ±20 mA VOUT < GND −20 VOUT < GND −20 mA DC Output Source/Sink Current ±25 mA DC Supply Current per Supply Pin or Ground Pin ±50 mA −65 to +150 °C 260 °C DC Output Voltage IIK DC Input Diode Current IOK DC Output Diode Current (NLV) 1Gxx 1GTxx DC Output Diode Current IOUT ICC or IGND TSTG Storage Temperature Range TL Lead Temperature, 1 mm from Case for 10 secs TJ Junction Temperature Under Bias +150 °C qJA Thermal Resistance (Note 2) SC−88A SC−74A SOT−553 SOT−953 UDFN6 377 320 324 254 154 °C/W PD Power Dissipation in Still Air SC−88A SC−74A SOT−553 SOT−953 UDFN6 332 390 386 491 812 mW Level 1 − MSL Moisture Sensitivity FR Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in − ESD Withstand Voltage (Note 3) Human Body Model Charged Device Model 2000 1000 V $100 mA VESD ILatchup Latchup Performance (Note 4) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Applicable to devices with outputs that may be tri−stated. 2. Measured with minimum pad spacing on an FR4 board, using 10mm−by−1inch, 2 ounce copper trace no air flow per JESD51−7. 3. HBM tested to ANSI/ESDA/JEDEC JS−001−2017. CDM tested to EIA/JESD22−C101−F. JEDEC recommends that ESD qualification to EIA/JESD22−A115−A (Machine Model) be discontinued per JEDEC/JEP172A. 4. Tested to EIA/JESD78 Class II. www.onsemi.com 3 MC74VHC1G03, MC74VHC1GT03 RECOMMENDED OPERATING CONDITIONS Symbol Characteristics VCC Positive DC Supply Voltage VIN DC Input Voltage VOUT DC Output Voltage (NLV) DC Output Voltage TA Max Unit 2.0 5.5 V 0 5.5 V 0 VCC V Active−Mode (High or Low State) Tri−State Mode (Note 1) Power−Down Mode (VCC = 0 V) 0 0 0 VCC 5.5 5.5 Active−Mode (High or Low State) Tri−State Mode (Note 1) Power−Down Mode (VCC = 0 V) 0 0 0 VCC 5.5 5.5 −55 +125 1Gxx 1GTxx tr , tf Min Operating Temperature Range Input Rise and Fall Time TSOP−5, SC−88A (NLV) VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 0 0 100 20 Input Rise and Fall Time SC−74A, SC−88A, UDFN6, SOT−553, SOT−953 VCC = 2.0 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 0 0 0 0 20 20 10 5 V °C ns/V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. DC ELECTRICAL CHARACTERISTICS (MC74VHC1G03) Symbol VIH VIL VOL Parameter Test Conditions High−Level Input Voltage Low−Level Input Voltage TA = 25°C −40°C ≤ TA ≤ 85°C −55°C ≤ TA ≤ 125°C VCC (V) Min Typ Max Min Max Min Max Unit 2.0 1.5 − − 1.5 − 1.5 − V 3.0 2.1 − − 2.1 − 2.1 − 4.5 3.15 − − 3.15 − 3.15 − 5.5 3.85 − − 3.85 − 3.85 − 2.0 − − 0.5 − 0.5 − 0.5 3.0 − − 0.9 − 0.9 − 0.9 4.5 − − 1.35 − 1.35 − 1.35 5.5 − − 1.65 − 1.65 − 1.65 2.0 3.0 4.5 3.0 4.5 − − − − − 0.0 0.0 0.0 − − 0.1 0.1 0.1 0.36 0.36 − − − − − 0.1 0.1 0.1 0.44 0.44 − − − − − 0.1 0.1 0.1 0.52 0.52 V Low−Level Output Voltage VIN = VIH or VIL IOL = 50 mA IOL = 50 mA IOL = 50 mA IOL = 4 mA IOL = 8 mA IIN Input Leakage Current VIN = 5.5 V or GND 2.0 to 5.5 − − ±0.1 − ±1.0 − $1.0 mA IOZ 3−State Output Leakage Current VOUT = 0 V to 5.5 V 5.5 − − ±0.25 − $2.5 − $2.5 mA IOFF Power Off Leakage Current (NLV) VIN = 5.5 V 0.0 − − 1.0 − 10 − 10 mA Power Off Leakage Current VIN = 5.5 V or VOUT = 5.5 V 0.0 − − 1.0 − 10 − 10 mA Quiescent Supply Current VIN = VCC or GND 5.5 − − 1.0 − 20 − 40 mA ICC www.onsemi.com 4 V MC74VHC1G03, MC74VHC1GT03 DC ELECTRICAL CHARACTERISTICS (MC74VHC1GT03) Symbol VIH VIL Parameter Test Conditions High−Level Input Voltage Low−Level Input Voltage TA = 25°C −40°C ≤ TA ≤ 85°C −55°C ≤ TA ≤ 125°C VCC (V) Min Typ Max Min Max Min Max Unit 2.0 1.0 − − 1.0 − 1.0 − V 3.0 1.4 − − 1.4 − 1.4 − 4.5 2.0 − − 2.0 − 2.0 − 5.5 2.0 − − 2.0 − 2.0 − 2.0 − − 0.28 − 0.28 − 0.28 3.0 − − 0.45 − 0.45 − 0.45 4.5 − − 0.8 − 0.8 − 0.8 5.5 − − 0.8 − 0.8 − 0.8 2.0 3.0 4.5 3.0 4.5 − − − − − 0.0 0.0 0.0 − − 0.1 0.1 0.1 0.36 0.36 − − − − − 0.1 0.1 0.1 0.44 0.44 − − − − − 0.1 0.1 0.1 0.52 0.52 V VOL Low−Level Output Voltage VIN = VIH or VIL IOL = 50 mA IOL = 50 mA IOL = 50 mA IOL = 4 mA IOL = 8 mA V IIN Input Leakage Current VIN = 5.5 V or GND 2.0 to 5.5 − − ±0.1 − ±1.0 − $1.0 mA IOZ 3−State Output Leakage Current VOUT = 0 V to 5.5 V 5.5 − − ±0.25 − $2.5 − $2.5 mA IOFF Power Off Leakage Current VIN = 5.5 V or VOUT = 5.5 V 0 − − 1.0 − 10 − 10 mA ICC Quiescent Supply Current VIN = VCC or GND 5.5 − − 1.0 − 20 − 40 mA ICCT Increase in Quiescent Supply Current per Input Pin One Input: VIN = 3.4 V; Other Input at VCC or GND 5.5 − − 1.35 − 1.5 − 1.65 mA AC ELECTRICAL CHARACTERISTICS TA = 25°C −40°C ≤ TA ≤ 85°C −55°C ≤ TA ≤ 125°C Symbol Parameter Conditions VCC (V) Min tPZL Propagation Delay, (A or B) to Y (Figures 3 and 4) CL = 15 pF 3.0 to 3.6 − 5.6 7.9 − 9.5 − 11.0 − 8.1 11.4 − 13.0 − 15.5 − 3.6 5.5 − 6.5 − 8.0 − 5.1 7.5 − 8.5 − 10.0 − 6.5 9.7 − 11.5 − 14.5 − 8.1 11.4 − 13.0 − 15.5 − 4.8 6.8 − 8.0 − 10.0 − 5.1 7.5 − 8.5 − 10.0 − 4.0 10 − 10 − 10 pF − 6.0 − − − − − pF CL = 50 pF CL = 15 pF 4.5 to 5.5 CL = 50 pF tPLZ Propagation Delay, (A or B) to Y (Figures 3 and 4) CL = 15 pF 3.0 to 3.6 CL = 50 pF CL = 15 pF 4.5 to 5.5 CL = 50 pF CIN COUT Input Capacitance Output Capacitance Output in High Impedance State Typ Max Min Max Min Max Unit ns ns Typical @ 25°C, VCC = 5.0 V CPD 8.0 Power Dissipation Capacitance (Note 5) pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD  VCC  fin + ICC. CPD is used to determine the no−load dynamic power consumption; PD = CPD  VCC2  fin + ICC  VCC. www.onsemi.com 5 MC74VHC1G03, MC74VHC1GT03 OPEN VCC Test Switch Position CL, pF RL, W tPLH / tPHL Open See AC Characteristics Table X tPLZ / tPZL VCC 1k tPHZ / tPZH GND 1k GND RL OUTPUT DUT RT X = Don’t Care CL * CL includes probe and jig capacitance RT is ZOUT of pulse generator (typically 50 W) f = 1 MHz Figure 3. Test Circuit tr = 3 ns tf = 3 ns 90% 90% Vmi INPUT Vmi INPUT Vmi 10% 10% tPHL Vmi GND GND tPZL tPLH Vmo OUTPUT VCC VCC tPLZ Vmo OUTPUT Vmo VOL + VY VOL VOL tPLH OUTPUT tPHL Vmo ~VCC VOH tPZH VOH Vmo tPHZ VOH VOH − VY Vmo OUTPUT VOL ~0 V Figure 4. Switching Waveforms Vmo, V VCC, V Vmi, V tPLH, tPHL 3.0 to 3.6 VCC/2 VCC/2 VCC/2 0.3 4.5 to 5.5 VCC/2 VCC/2 VCC/2 0.3 www.onsemi.com 6 tPZL, tPLZ, tPZH, tPHZ VY, V MC74VHC1G03, MC74VHC1GT03 ORDERING INFORMATION Packages Specific Device Code Pin 1 Orientation (See below) Shipping† MC74VHC1G03DFT1G SC−88A VP Q2 3000 / Tape & Reel MC74VHC1G03DFT2G SC−88A VP Q4 3000 / Tape & Reel MC74VHC1G03DFT2G−L22038** SC−88A VP Q4 3000 / Tape & Reel NLVVHC1G03DFT1G* SC−88A VP Q2 3000 / Tape & Reel MC74VHC1GT03DFT1G (In Development) SC−88A TBD Q2 3000 / Tape & Reel MC74VHC1GT03DFT2G (In Development) SC−88A TBD Q4 3000 / Tape & Reel MC74VHC1G03DBVT1G SC−74A VP Q4 3000 / Tape & Reel MC74VHC1GT03DBVT1G (In Development) SC−74A TBD Q4 3000 / Tape & Reel MC74VHC1G03DTT1G** TSOP−5 VP Q4 3000 / Tape & Reel MC74VHC1GT03DTT1G (In Development) TSOP−5 TBD Q4 3000 / Tape & Reel MC74VHC1G03XV5T2G (In Development) SOT−553 TBD Q4 4000 / Tape & Reel MC74VHC1GT03XV5T2G (In Development) SOT−553 TBD Q4 4000 / Tape & Reel MC74VHC1G03P5T5G (In Development) SOT−953 TBD Q2 8000 / Tape & Reel MC74VHC1GT03P5T5G (In Development) SOT−953 TBD Q2 8000 / Tape & Reel MC74VHC1G03MU1TCG (In Development) UDFN6, 1.45 x 1.0, 0.5P TBD Q4 3000 / Tape & Reel MC74VHC1GT03MU1TCG (In Development) UDFN6, 1.45 x 1.0, 0.5P TBD Q4 3000 / Tape & Reel MC74VHC1G03MU3TCG (In Development) UDFN6, 1.0 x 1.0, 0.35P TBD Q4 3000 / Tape & Reel MC74VHC1GT03MU3TCG (In Development) UDFN6, 1.0 x 1.0, 0.35P TBD Q4 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. ** Please refer to NLV specifications for this device. Pin 1 Orientation in Tape and Reel www.onsemi.com 7 MC74VHC1G03, MC74VHC1GT03 PACKAGE DIMENSIONS SC−88A (SC−70−5/SOT−353) CASE 419A−02 ISSUE L A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 −B− S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) M B M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 J C K H SOLDER FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 8 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 MC74VHC1G03, MC74VHC1GT03 PACKAGE DIMENSIONS SC−74A CASE 318BQ ISSUE B 5X b 0.20 C A B E1 5 M 4 1 2 E 3 B 0.05 A1 L DETAIL A e A D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. TOP VIEW A SIDE VIEW C DETAIL A c SEATING PLANE END VIEW DIM A A1 b c D E E1 e L M MILLIMETERS MIN MAX 0.90 1.10 0.01 0.10 0.25 0.50 0.10 0.26 2.85 3.15 2.50 3.00 1.35 1.65 0.95 BSC 0.20 0.60 0_ 10 _ RECOMMENDED SOLDERING FOOTPRINT* 0.95 PITCH 2.40 5X 1.00 5X 0.70 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 9 MC74VHC1G03, MC74VHC1GT03 PACKAGE DIMENSIONS TSOP−5 CASE 483 ISSUE N 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSION A. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. D 5X NOTE 5 0.20 C A B 0.10 T M 2X 0.20 T B 5 1 4 2 B S 3 K DETAIL Z G A A TOP VIEW DIM A B C D G H J K M S DETAIL Z J C 0.05 H SIDE VIEW C SEATING PLANE END VIEW MILLIMETERS MIN MAX 2.85 3.15 1.35 1.65 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 10 MC74VHC1G03, MC74VHC1GT03 PACKAGE DIMENSIONS SOT−553, 5 LEAD CASE 463B ISSUE C D −X− 5 A 4 1 e 2 L E −Y− 3 b HE DIM A b c D E e L HE c 5 PL 0.08 (0.003) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. M X Y MILLIMETERS NOM MAX 0.55 0.60 0.22 0.27 0.13 0.18 1.60 1.65 1.20 1.25 0.50 BSC 0.10 0.20 0.30 1.55 1.60 1.65 MIN 0.50 0.17 0.08 1.55 1.15 SOLDERING FOOTPRINT* 0.3 0.0118 0.45 0.0177 1.35 0.0531 1.0 0.0394 0.5 0.5 0.0197 0.0197 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 11 INCHES NOM 0.022 0.009 0.005 0.063 0.047 0.020 BSC 0.004 0.008 0.061 0.063 MIN 0.020 0.007 0.003 0.061 0.045 MAX 0.024 0.011 0.007 0.065 0.049 0.012 0.065 MC74VHC1G03, MC74VHC1GT03 PACKAGE DIMENSIONS SOT−953 CASE 527AE ISSUE E X D PIN ONE INDICATOR 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF THE BASE MATERIAL. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. A Y 4 HE E 1 2 3 DIM A b C D E e HE L L2 L3 C TOP VIEW SIDE VIEW e L 5X 5X L3 MILLIMETERS MIN NOM MAX 0.34 0.37 0.40 0.10 0.15 0.20 0.07 0.12 0.17 0.95 1.00 1.05 0.75 0.80 0.85 0.35 BSC 0.95 1.00 1.05 0.175 REF 0.05 0.10 0.15 −−− −−− 0.15 SOLDERING FOOTPRINT* 5X 0.35 5X 0.20 5X L2 5X BOTTOM VIEW b PACKAGE OUTLINE 0.08 X Y 1.20 1 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 12 MC74VHC1G03, MC74VHC1GT03 PACKAGE DIMENSIONS UDFN6, 1.45x1.0, 0.5P CASE 517AQ ISSUE O A B D L L NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. L1 PIN ONE REFERENCE 0.10 C ÉÉÉ ÉÉÉ DETAIL A E OPTIONAL CONSTRUCTIONS ÉÉÉ ÉÉÉ EXPOSED Cu TOP VIEW 0.10 C DETAIL B MOLD CMPD DETAIL B 0.05 C 6X DIM A A1 A2 b D E e L L1 OPTIONAL CONSTRUCTIONS A MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.07 REF 0.20 0.30 1.45 BSC 1.00 BSC 0.50 BSC 0.30 0.40 −−− 0.15 MOUNTING FOOTPRINT 0.05 C A1 SIDE VIEW A2 e 6X C 6X SEATING PLANE L 1.24 3 1 DETAIL A 6X 0.53 6 0.30 PACKAGE OUTLINE 4 BOTTOM VIEW 6X 0.50 PITCH DIMENSIONS: MILLIMETERS b 0.10 C A B 0.05 C 1 *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 www.onsemi.com 13 MC74VHC1G03, MC74VHC1GT03 PACKAGE DIMENSIONS UDFN6, 1x1, 0.35P CASE 517BX ISSUE O PIN ONE REFERENCE 2X 0.08 C 2X ÉÉÉ ÉÉÉ 0.08 C 0.05 C L1 A B D L NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. L3 E DETAIL A ALTERNATE TERMINAL CONSTRUCTION ÉÉ ÉÉ ÇÇ TOP VIEW EXPOSED Cu DETAIL B A3 A1 MOLD CMPD DETAIL B A ALTERNATE CONSTRUCTION 0.05 C SIDE VIEW C SEATING PLANE 3 1 6X MILLIMETERS MIN MAX 0.50 0.65 0.00 0.05 0.13 REF 0.17 0.23 1.00 BSC 1.00 BSC 0.35 0.20 0.40 −−− 0.15 0.26 0.33 RECOMMENDED SOLDERING FOOTPRINT* e DETAIL A DIM A A1 A3 b D E e L L1 L3 L 6X 0.25 6X 0.52 1.20 6 4 BOTTOM VIEW 6X PACKAGE OUTLINE b 0.07 M C A B 0.05 M C 1 0.35 PITCH NOTE 3 DIMENSION: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 14 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative