NC7NZ14L8X

DATA SHEET www.onsemi.com TinyLogic UHS Triple Inverter with Schmitt Trigger Input MARKING DIAGRAMS UQFN8 1.6X1.6, 0.5P CASE 523AY NC7NZ14 P6KK XYZ Description The NC7NZ14 is a triple inverter with Schmitt trigger input from onsemi’s Ultra−High Speed (UHS) series of TinyLogic. The device is fabricated with advanced CMOS technology to achieve ultra−high speed with high output drive while maintaining low static power dissipation over a very broad VCC operating range. The device is specified to operate over the 1.65 V to 5.5 V VCC range. The inputs and outputs are high−impedance when VCC is 0 V. Inputs tolerate voltages up to 5.5 V independent of VCC operating voltage. Features • • • • • • • • • Ultra High−Speed: tPD = 3.7 ns (Typical) into 50 pF at 5 V VCC High Output Drive: ±24 mA at 3 V VCC Broad VCC Operating Range: 1.65 V to 5.5 V Power Down High Impedance Inputs / Outputs Over−Voltage Tolerance Inputs Facilitate 5 V to 3 V Translation Proprietary Noise / EMI Reduction Circuitry Ultra−Small MicroPak™ Packages Space−Saving US8 Surface Mount Package These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant US8 CASE 846AN P6, NZ14 KK XY Z A L YW NZ14 ALYW = Specific Device Code = 2−Digit Lot Run Traceability Code = 2−Digit Date Code Format = Assembly Plant Code = Assembly Site = Wafer Lot Number = Assembly Start Week ORDERING INFORMATION See detailed ordering, marking and shipping information on page 6 of this data sheet. IEEC / IEC 1A 2A 3A (1) (7) (3) (5) (6) (2) 1Y 2Y 3Y Figure 1. Logic Symbol VCC 1Y 3A 2Y 8 7 6 5 1 2 3 4 1A 3Y 2A GND Figure 2. Connection Diagram (Top View) © Semiconductor Components Industries, LLC, 2001 June, 2022 − Rev. 4 1 Publication Order Number: NC7NZ14/D NC7NZ14 Pin Configurations 1A 7 AAA 3Y 6 2A 5 VCC 8 Pin One NOTES: 1. AAA represents product code top mark (see ordering table). 2. Orientation of top mark determines pin one location. Reading the top product code mark left to right, pin one is the lower left pin. 4 GND 1 1Y Figure 3. US8 2 3A 3 2Y Figure 4. MicroPak (Top Through View) PIN DEFINITIONS FUNCTION TABLE Pin # US8 Pin # MicroPak Name 1 7 1A 2 6 3 4 Description Input Output Input A Y 3Y Output L H 5 2A Input H L 4 GND Ground 5 3 2Y Output 6 2 3A Input 7 1 1Y Output 8 8 VCC H = HIGH Logic Level L = LOW Logic Level Supply Voltage www.onsemi.com 2 NC7NZ14 ABSOLUTE MAXIMUM RATINGS Symbol Min Max Unit VCC Supply Voltage −0.5 6.5 V VIN DC Input Voltage −0.5 6.5 V DC Output Voltage −0.5 6.5 V VOUT Parameter IIK DC Input Diode Current VIN < 0 V − −50 mA IOK DC Output Diode Current VOUT < 0 V − −50 mA IOUT DC Output Current − ±50 mA DC VCC or Ground Current − ±50 mA −65 +150 °C ICC / IGND TSTG Storage Temperature Range TJ Junction Temperature Under Bias − +150 °C TL Junction Lead Temperature (Soldering, 10 Seconds) − +260 °C PD Power Dissipation in Still Air US8 − 500 mW MicroPak−8 ESD − 539 Human Body Model, JEDEC: JESD22−A114 − 4000 Charge Device Model, JEDEC: JESD22−C101 − 2000 V Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN VOUT Parameter Min Max Unit Supply Voltage Operating 1.65 5.5 V Supply Voltage Data Retention 1.5 5.5 Input Voltage 0 5.5 V Output Voltage 0 VCC V TA Operating Temperature qJA Thermal Resistance Conditions −40 +85 °C US8 − 250 °C/W MicroPak−8 − 232 Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 3. Unused inputs must be held HIGH or LOW. They may not float. www.onsemi.com 3 NC7NZ14 DC ELECTICAL CHARACTERISTICS TA = −40 to +85°C TA = +25°C Typ Max Min Max Unit V Symbol Parameter VCC (V) VP Positive Threshold Voltage 1.65 − 1.10 1.50 − 1.50 2.30 − 1.40 1.80 − 1.80 3.00 − 1.75 2.20 − 2.20 4.50 − 2.45 3.10 − 3.10 5.50 − 2.90 3.60 − 3.60 1.65 0.25 0.55 − 0.25 − 2.30 0.40 0.75 − 0.40 − 3.00 0.60 1.00 − 0.60 − 4.50 1.00 1.43 − 1.00 − 5.50 1.20 1.70 − 1.20 − 1.65 0.15 0.54 1.00 0.15 1.00 2.30 0.25 0.65 1.10 0.25 1.10 3.00 0.40 0.77 1.20 0.40 1.20 4.50 0.60 1.01 1.50 0.60 1.50 5.50 0.70 1.18 1.70 0.70 1.70 1.55 1.65 − 1.55 − VN VH VOH Negative Threshold Voltage Hysteresis Voltage HIGH Level Output Voltage 1.65 2.30 VOL LOW Level Output Voltage Input Leakage Current IOFF Power Off Leakage Current ICC Quiescent Supply Current VIN = VP or VN, IOH = −100 mA 2.20 2.30 − 2.20 − 3.00 2.90 3.00 − 2.90 − 4.50 4.40 4.50 − 4.4 − 1.65 IOH = −4 mA 1.29 1.52 − 1.29 − 2.30 IOH = −8 mA 1.90 2.15 − 1.90 − 3.00 IOH = −16 mA 2.40 2.80 − 2.40 − 3.00 IOH = −24 mA 2.30 2.68 − 2.30 − 4.50 IOH = −32 mA 3.80 4.20 − 3.80 − 1.65 VIN = VP or VN, IOL = 100 mA − 0.00 0.10 − 0.10 − 0.00 0.10 − 0.10 3.00 − 0.00 0.10 − 0.10 4.50 − 0.00 0.10 − 0.10 2.30 IIN Conditions Min V V V V 1.65 IOL = 4 mA − 0.08 0.24 − 0.24 2.30 IOL = 8 mA − 0.10 0.30 − 0.30 3.00 IOL = 16 mA − 0.15 0.40 − 0.40 3.00 IOL = 24 mA − 0.22 0.55 − 0.55 4.50 IOL = 32 mA − 0.22 0.55 − 0.55 VIN = 5.5 V, GND − − ±0.1 − ±1.0 mA VIN or VOUT = 5.5 V − − 1 − 10 mA − − 1.0 − 10 mA 1.65 to 5.5 0 1.65 to 5.50 VIN = 5.5 V, GND www.onsemi.com 4 NC7NZ14 AC ELECTRICAL CHARACTERISTICS TA = +25°C Symbol Parameter tPLH, tPHL Propagation Delay (Figure 5, 6) TA = −40 to +85°C Min Typ Max Min Max Unit − 7.6 12.5 − 13.0 ns − 5.0 9.0 − 9.5 3.30 ±0.30 − 3.7 6.3 − 6.5 5.00 ±0.50 − 3.1 5.2 − 5.5 − 4.4 7.2 − 7.5 − 3.7 5.9 − 6.2 VCC (V) 1.80 ±0.15 2.50 ±0.20 3.30 ±0.30 5.00 ±0.50 Conditions CL = 15 pF, RL = 1 MW, CL = 50 pF, RL = 500 W, CIN Input Capacitance 0.00 − 2.5 − − − pF CPD Power Dissipation Capacitance (Note 4) (Figure 7) 3.30 − 9 − − − pF 5.00 − 11 − − − 4. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression: ICCD = (CPD) (VCC) (fIN) + (ICCstatic). tf = 3 ns tr = 3 ns 90% VCC 50% INPUT 10% INPUT 90% TW 50% 10% OUTPUT CL tPLH RL OUTPUT NOTE: 5. CL includes load and stray capacitance; Input PRR = 1.0 MHz, tW = 500 ns. tPHL 50% VCC GND VOH 50% VOL Figure 5. AC Test Circuit Figure 6. AC Waveforms VCC A INPUT NOTE: 6. Input = AC Waveform; tr = tf = 1.8 ns; PRR = 10 MHz; Duty Cycle = 50%. Figure 7. ICCD Test Circuit www.onsemi.com 5 NC7NZ14 ORDERING INFORMATION Top Mark Package Shipping† NC7NZ14K8X NZ14 8−Lead US8, JEDEC MO−187, Variation CA 3.1 mm Wide 3000 / Tape & Reel NC7NZ14L8X P6 8−Lead MicroPak, 1.6 mm Wide 5000 / Tape & Reel NC7NZ14L8X−L22185 P6 8−Lead MicroPak, 1.6 mm Wide 5000 / Tape & Reel Part Number †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MicroPak is trademark of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. www.onsemi.com 6 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS UQFN8 1.6X1.6, 0.5P CASE 523AY ISSUE O 0.05 C A 1.60 DATE 31 AUG 2016 0.40 (6X) 1.60 B 0.45 (2X) 2X 1.60 TOP VIEW PIN#1 IDENT 0.05 1.61 C 0.50 RECOMMENDED LAND PATTERN 0.50±0.05 0.05 C 0.05 C 0.25 (8X) NOTES: SEATING PLANE 0.025±0.025 A. PACKAGE CONFORMS TO JEDEC MO−255 VARIATION UAAD. C B. DIMENSIONS ARE IN MILLIMETERS. SIDE VIEW C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 2009. 1.60±0.05 (0.10) D. LAND PATTERN RECOMMENDATION IS EXISTING INDUSTRY LAND PATTERN. (0.20)3X DETAIL A 1 2 3 (0.20) (0.09) 4 8 1.60±0.05 0.30±0.05 0.30±0.05 (7X) 7 6 5 0.50 1.00±0.05 (0.15) 0.20±0.05 (8X) BOTTOM VIEW DOCUMENT NUMBER: DESCRIPTION: 98AON13591G UQFN8 1.6X1.6, 0.5P 0.30±0.05 0.10 C 0.05 C A B DETAIL A SCALE : 2X Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS US8 CASE 846AN ISSUE O DOCUMENT NUMBER: DESCRIPTION: 98AON13778G US8 DATE 31 DEC 2016 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative