DATA SHEET
www.onsemi.com
TinyLogic ULP-A Buffer
with Three-State Output
NC7SP126
MARKING
DIAGRAMS
SIP6 1.45X1.0
MicroPak
CASE 127EB
The NC7SP126 is a single non−inverting 3−state buffer in tiny
footprint packages. The device is designed to operate for VCC = 0.9 V
to 3.6 V.
Pin 1
UDFN6
MicroPak2
CASE 517DP
Features
•
•
•
•
•
•
•
Designed for 0.9 V to 3.6 V VCC Operation
2.6 ns tPD at 3.3 V (Typ)
Inputs/Outputs Over−Voltage Tolerant up to 3.6 V
IOFF Supports Partial Power Down Protection
Source/Sink 2.6 mA at 3.3 V
Available in SC−88A and MicroPak™ Packages
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
OE
5
1
VCC
A 2
OE
1
GND 3
4
Y
GND
CCKK
XYZ
Pin 1
CC
KK
XY
Z
= Specific Device Code
= 2−Digit Lot Run Traceability Code
= 2−Digit Date Code
= Assembly Plant Code
SC−88A
CASE 419A−02
XXXMG
G
XXX = Specific Device Code
M
= Date Code
G
= Pb−Free Package
6 VCC
A 2
CCKK
XYZ
5 NC
3
4 Y
SC−88A
ORDERING INFORMATION
MicroPak
See detailed ordering, marking and shipping information on
page 7 of this data sheet.
Figure 1. Pinout Diagrams (Top Views)
OE
EN
Y
A
Figure 2. Logic Symbol
PIN ASSIGNMENT
FUNCTION TABLE
Pin
SC88A
MicroPak
Input
Output
1
OE
OE
OE
A
Y
2
A
A
L
X
Z
3
GND
GND
H
L
L
4
Y
Y
H
H
H
5
VCC
N.C.
6
−
VCC
X = Don’t Care
Z = High Impedance State
N.C. = No Connect
© Semiconductor Components Industries, LLC, 2002
May, 2022 − Rev. 4
1
Publication Order Number:
NC7SP126/D
NC7SP126
MAXIMUM RATINGS
Symbol
Value
Unit
VCC
DC Supply Voltage
−0.5 to +4.3
V
VIN
DC Input Voltage
−0.5 to +4.3
V
−0.5 to VCC + 0.5
−0.5 to +4.3
−0.5 to +4.3
V
VIN < GND
−50
mA
VOUT < GND
−50
mA
VOUT
Characteristics
DC Output Voltage
Active−Mode (High or Low State)
Tri−State Mode (Note 1)
Power−Down Mode (VCC = 0 V)
IIK
DC Input Diode Current
IOK
DC Output Diode Current
IOUT
DC Output Source/Sink Current
±50
mA
DC Supply Current per Supply Pin or Ground Pin
±50
mA
ICC or IGND
TSTG
−65 to +150
°C
TL
Storage Temperature Range
Lead Temperature, 1 mm from Case for 10 Seconds
260
°C
TJ
Junction Temperature Under Bias
+150
°C
qJA
Thermal Resistance (Note 2)
SC−88A
MicroPak
377
154
°C/W
PD
Power Dissipation in Still Air
SC−88A
MicroPak
332
812
mW
Level 1
−
MSL
Moisture Sensitivity
FR
Flammability Rating
Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
−
ESD Withstand Voltage (Note 3)
Human Body Model
Charged Device Model
4000
2000
V
±100
mA
VESD
ILatchup
Latchup Performance (Note 4)
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Applicable to devices with outputs that may be tri−stated.
2. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow per JESD51−7.
3. HBM tested to EIA / JESD22−A114−A. CDM tested to JESD22−C101−A. JEDEC recommends that ESD qualification to EIA/JESD22−A115A
(Machine Model) be discontinued.
4. Tested to EIA/JESD78 Class II.
www.onsemi.com
2
NC7SP126
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
VCC
Positive DC Supply Voltage
VIN
DC Input Voltage
VOUT
TA
tr , tf
DC Output Voltage
Min
Max
Unit
0.9
3.6
V
0
3.6
V
0
0
0
VCC
3.6
3.6
−40
+85
°C
0
10
ns/V
Active−Mode (High or Low State)
Tri−State Mode (Note 1)
Power−Down Mode (VCC = 0 V)
Operating Temperature Range
Input Transition Rise and Fall Time
VCC = 3.3 V ± 0.3 V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
TA = 255C
Symbol
VIH
VIL
VOH
Parameter
Condition
High−Level Input
Voltage
Low−Level Input
Voltage
High−Level Output
Voltage
VCC (V)
TA = −405C to +855C
Min
Typ
Max
Min
Max
Unit
V
0.9
−
0.5
−
−
−
1.1 to 1.3
0.65 x VCC
−
−
0.65 x VCC
−
1.4 to 1.6
0.65 x VCC
−
−
0.65 x VCC
−
1.65 to 1.95 0.65 x VCC
−
−
0.65 x VCC
−
2.3 to 2.7
1.6
−
−
1.6
−
3.0 to 3.6
2.1
−
−
2.1
−
0.9
−
0.5
−
−
−
1.1 to 1.3
−
−
0.35 x VCC
−
0.35 x VCC
1.4 to 1.6
−
−
0.35 x VCC
−
0.35 x VCC
1.65 to 1.95
−
−
0.35 x VCC
−
0.35 x VCC
2.3 to 2.7
−
−
0.7
−
0.7
3.0 to 3.6
−
−
0.9
−
0.9
VIN = VIH or VIL
V
0.9
−
VCC −
0.1
−
−
−
1.1 to 1.3
VCC − 0.1
−
−
VCC − 0.1
−
1.4 to 1.6
VCC − 0.1
−
−
VCC − 0.1
−
1.65 to 1.95
VCC − 0.1
−
−
VCC − 0.1
−
2.3 to 2.7
VCC − 0.1
−
−
VCC − 0.1
−
3.0 to 3.6
VCC − 0.1
−
−
VCC − 0.1
−
IOH = −0.5 mA
1.1 to 1.3
0.75 x VCC
−
−
0.70 x VCC
−
IOH = −1 mA
1.4 to 1.6
1.07
−
−
0.99
−
IOH = −1.5 mA
1.65 to 1.95
1.24
−
−
1.22
−
IOH = −2.1 mA
2.3 to 2.7
1.95
−
−
1.87
−
IOH = −2.6 mA
3.0 to 3.6
2.61
−
−
2.55
−
IOH = −20 mA
V
www.onsemi.com
3
NC7SP126
DC ELECTRICAL CHARACTERISTICS (continued)
TA = −405C to +855C
TA = 255C
Symbol
Parameter
VOL
Low−Level Output
Voltage
Condition
Min
VCC (V)
Typ
Max
Min
Max
VIN = VIH or VIL
Unit
V
0.9
−
0.1
−
−
−
1.1 to 1.3
−
−
0.1
−
0.1
1.4 to 1.6
−
−
0.1
−
0.1
1.65 to 1.95
−
−
0.1
−
0.1
2.3 to 2.7
−
−
0.1
−
0.1
3.0 to 3.6
−
−
0.1
−
0.1
IOL = 0.5 mA
1.1 to 1.3
−
−
0.3 x VCC
−
0.3 x VCC
IOL = 1 mA
1.4 to 1.6
−
−
0.31
−
0.37
IOL = 1.5 mA
1.65 to 1.95
−
−
0.31
−
0.35
IOL = 2.1 mA
2.3 to 2.7
−
−
0.31
−
0.33
IOL = 2.6 mA
3.0 to 3.6
−
−
0.31
−
0.33
IOL = 20 mA
IIN
Input Leakage
Current
VIN = 0 V to 3.6 V
0.9 to 3.6
−
−
±0.1
−
±0.5
mA
IOZ
3−State Output
Leakage Current
VIN = VIH or VIL
VOUT = 0 V to 3.6 V
0.9 to 3.6
−
−
±0.5
−
±0.5
mA
IOFF
Power Off Leakage
Current
VIN = 0 V to 3.6 V or
VOUT = 0 V to 3.6 V
0
−
−
0.5
−
0.5
mA
ICC
Quiescent Supply
Current
VIN = VCC or GND
0.9 to 3.6
−
−
0.9
−
0.9
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
AC ELECTRICAL CHARACTERISTICS
TA = 25°C
Symbol
Parameter
tPLH, tPHL Propagation Delay,
A to Y (Figures 3 and 4)
tPZH, tPZL Output Enable Time,
OE to Y
(Figures 3 and 4)
tPHZ, tPLZ Output Disable Time,
OE to Y
(Figures 3 and 4)
TA = −405C to +855C
Condition
VCC (V)
Min
Typ
Max
Min
Max
Unit
RL = 1 MW, CL = 10 pF
0.9
−
50.7
−
−
−
ns
1.10 to 1.30
−
13.4
27.6
−
39.6
1.40 to 1.60
−
6.8
11.2
−
14.5
1.65 to 1.95
−
4.8
8.6
−
11.6
2.3 to 2.7
−
3.1
6.3
−
8.2
3.0 to 3.6
−
2.6
5.3
−
7.2
0.9
−
50.6
−
−
−
1.10 to 1.30
−
13.2
26.7
−
40.4
1.40 to 1.60
−
6.7
11.9
−
14.8
1.65 to 1.95
−
4.7
9.7
−
12.3
2.3 to 2.7
−
3.0
7.7
−
10.5
3.0 to 3.6
−
2.5
6.9
−
8.6
R1 = RL = 5 kW
CL = 10 pF
R1 = RL = 5 kW
CL = 10 pF
0.9
−
14.6
−
−
−
1.10 to 1.30
−
8.2
20.5
−
42.0
1.40 to 1.60
−
6.3
15.3
−
18.0
1.65 to 1.95
−
6.1
14.7
−
17.8
2.3 to 2.7
−
5.8
13.7
−
15.0
3.0 to 3.6
−
5.7
13.5
−
14.8
www.onsemi.com
4
ns
ns
NC7SP126
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎ
AC ELECTRICAL CHARACTERISTICS (continued)
TA = 25°C
Symbol
Parameter
tPLH, tPHL Propagation Delay,
A to Y (Figures 3 and 4)
tPZH, tPZL Output Enable Time,
OE to Y
(Figures 3 and 4)
tPHZ, tPLZ Output Disable Time,
OE to Y
(Figures 3 and 4)
tPLH, tPHL Propagation Delay,
A to Y (Figures 3 and 4)
tPZH, tPZL Output Enable Time,
OE to Y
(Figures 3 and 4)
tPHZ, tPLZ Output Disable Time,
OE to Y
(Figures 3 and 4)
Condition
VCC (V)
Min
Typ
RL = 1 MW, CL = 15 pF
R1 = RL = 5 kW
CL = 15 pF
R1 = RL = 5 kW
CL = 15 pF
R1 = RL = 5 kW
CL = 30 pF
Min
Max
Unit
ns
0.9
−
52.3
−
−
−
1.10 to 1.30
−
14.0
28.6
−
42.5
1.40 to 1.60
−
7.2
11.8
−
15.4
1.65 to 1.95
−
5.2
9.1
−
12.2
2.3 to 2.7
−
3.4
6.6
−
8.6
3.0 to 3.6
−
2.8
5.6
−
7.5
0.9
−
52.2
−
−
−
1.10 to 1.30
−
13.7
27.9
−
43.3
1.40 to 1.60
−
7.1
12.5
−
15.5
1.65 to 1.95
−
5.1
10.2
−
12.9
2.3 to 2.7
−
3.2
8.0
−
9.9
3.0 to 3.6
−
2.7
7.2
−
8.9
0.9
−
16.1
−
−
−
1.10 to 1.30
−
9.3
21.6
−
44.9
1.40 to 1.60
−
7.1
15.9
−
18.8
1.65 to 1.95
−
7.1
15.2
−
18.2
2.3 to 2.7
−
6.8
14.1
−
15.4
3.0 to 3.6
−
6.5
13.9
−
15.1
RL = 1 MW, CL = 30 pF
R1 = RL = 5 kW
CL = 30 pF
TA = −405C to +855C
Max
0.9
−
56.9
−
−
−
1.10 to 1.30
−
15.6
32.0
−
51.1
1.40 to 1.60
−
8.6
13.8
−
17.7
1.65 to 1.95
−
6.3
10.6
−
14.0
2.3 to 2.7
−
4.1
7.6
−
9.9
3.0 to 3.6
−
3.4
6.4
−
8.9
0.9
−
56.8
−
−
−
1.10 to 1.30
−
15.4
31.6
−
51.9
1.40 to 1.60
−
8.5
14.5
−
17.9
1.65 to 1.95
−
6.2
11.7
−
14.7
2.3 to 2.7
−
3.9
9.1
−
11.1
3.0 to 3.6
−
3.3
8.1
−
10.1
0.9
−
20.3
−
−
−
1.10 to 1.30
−
12.3
24.8
−
53.5
1.40 to 1.60
−
10.2
20.5
−
21.1
1.65 to 1.95
−
10.2
19.5
−
20.5
2.3 to 2.7
−
9.5
18.5
−
19.5
3.0 to 3.6
−
8.6
14.8
−
16.3
ns
ns
ns
ns
ns
CAPACITIVE CHARACTERISTICS
Symbol
CIN
Parameter
Test Condition
Typical (TA = 25°C)
Unit
Input Capacitance
VCC = 0 V
2.0
pF
COUT
Output Capacitance
VCC = 0 V
4.0
pF
CPD
Power Dissipation Capacitance (Note 5)
f = 10 MHz, VCC = 0.9 to 3.6 V, VIN = 0 V or VCC
8.0
pF
5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic
power consumption: PD = CPD VCC2 fin + ICC VCC.
www.onsemi.com
5
NC7SP126
OPEN
2 x VCC
GND
R1
INPUT
OUTPUT
DUT
RL
RT
Test
Switch Position
tPLH / tPHL
Open
tPLZ / tPZL
2 x VCC
tPHZ / tPZH
GND
CL *
CL includes probe and jig capacitance
RT is ZOUT of pulse generator (typically 50 W)
f = 1 MHz
Figure 3. Test Circuit
tr = 3 ns
tf = 3 ns
90%
90%
Vmi
INPUT
Vmi
INPUT
Vmi
10%
10%
tPHL
Vmi
GND
GND
tPZL
tPLH
Vmo
OUTPUT
VCC
VCC
tPLZ
VOH
Vmo
OUTPUT
Vmo
VOL + VY
VOL
VOL
tPLH
tPHL
Vmo
OUTPUT
tPZH
VOH
Vmo
~VCC
tPHZ
VOH
VOH − VY
Vmo
OUTPUT
VOL
~0 V
VCC, V
Vmi, V
Vmo, V
VY, V
0.9
VCC / 2
VCC / 2
0.1
1.1 to 1.3
VCC / 2
VCC / 2
0.1
1.4 to 1.6
VCC / 2
VCC / 2
0.1
1.65 to 1.95
VCC / 2
VCC / 2
0.15
2.3 to 2.7
VCC / 2
VCC / 2
0.15
3.0 to 3.6
1.5
1.5
0.3
Figure 4. Switching Waveforms
www.onsemi.com
6
NC7SP126
ORDERING INFORMATION
Package
Marking
Pin 1 Orientation
(See below)
Shipping†
SC−88A
P26
Q4
3000 / Tape & Reel
NC7SP126P5X−L22735
SC−88A
P26
Q4
3000 / Tape & Reel
NC7SP126L6X
MicroPak
L6
Q4
5000 / Tape & Reel
NC7SP126FHX
MicroPak2
L6
Q4
5000 / Tape & Reel
NC7SP126FHX−L22780
MicroPak2
L6
Q4
5000 / Tape & Reel
Device
NC7SP126P5X
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Pin 1 Orientation in Tape and Reel
MicroPak is trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
www.onsemi.com
7
NC7SP126
PACKAGE DIMENSIONS
SIP6 1.45X1.0
CASE 127EB
ISSUE O
www.onsemi.com
8
NC7SP126
PACKAGE DIMENSIONS
UDFN6 1.0X1.0, 0.35P
CASE 517DP
ISSUE O
www.onsemi.com
9
NC7SP126
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
G
5
4
−B−
S
1
2
DIM
A
B
C
D
G
H
J
K
N
S
3
D 5 PL
0.2 (0.008)
B
M
M
N
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
J
C
K
H
SOLDER FOOTPRINT
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
SCALE 20:1
mm Ǔ
ǒinches
STYLE 1:
PIN 1. BASE
2. EMITTER
3. BASE
4. COLLECTOR
5. COLLECTOR
STYLE 2:
PIN 1. ANODE
2. EMITTER
3. BASE
4. COLLECTOR
5. CATHODE
STYLE 3:
PIN 1. ANODE 1
2. N/C
3. ANODE 2
4. CATHODE 2
5. CATHODE 1
STYLE 4:
PIN 1. SOURCE 1
2. DRAIN 1/2
3. SOURCE 1
4. GATE 1
5. GATE 2
STYLE 6:
PIN 1. EMITTER 2
2. BASE 2
3. EMITTER 1
4. COLLECTOR
5. COLLECTOR 2/BASE 1
STYLE 7:
PIN 1. BASE
2. EMITTER
3. BASE
4. COLLECTOR
5. COLLECTOR
STYLE 8:
PIN 1. CATHODE
2. COLLECTOR
3. N/C
4. BASE
5. EMITTER
STYLE 9:
PIN 1. ANODE
2. CATHODE
3. ANODE
4. ANODE
5. ANODE
www.onsemi.com
10
STYLE 5:
PIN 1. CATHODE
2. COMMON ANODE
3. CATHODE 2
4. CATHODE 3
5. CATHODE 4
Note: Please refer to datasheet for
style callout. If style type is not called
out in the datasheet refer to the device
datasheet pinout or pin assignment.
NC7SP126
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
www.onsemi.com
11
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
工商网监
湘ICP备2023018690号
