DATA SHEET
www.onsemi.com
TinyLogic UHS Dual Buffer
with Schmitt Trigger Inputs
MARKING
DIAGRAMS
NC7WZ17
Description
Pin 1
The NC7WZ17 is a dual buffer with Schmitt trigger inputs from
onsemi’s Ultra−High Speed (UHS) series of TinyLogic products. The
device is fabricated with advanced CMOS technology to achieve
ultra−high speed with high output drive, while maintaining low static
power dissipation over a very broad VCC operating range. The device
is specified to operate over the 1.65 V to 5.5 V VCC range. The inputs
and outputs are high−impedance when VCC is 0 V. Inputs tolerate
voltages up to 5.5 V, independent of VCC operating voltage. Schmitt
trigger inputs achieve 1 V typical hysteresis between the positive− and
negative−going input threshold voltage at 5 V.
UDFN6
1.0X1.0, 0.35P
CASE 517DP
A5KK
XYZ
Pin 1
6
SC−88
CASE 419B−02
Z17 M•
•
1
Features
•
•
•
•
•
•
•
•
•
•
A5KK
XYZ
SIP6 1.45x1.0
CASE 127EB
Ultra−High Speed: tPD = 3.6 ns (Typical) into 50 pF at 5 V VCC
High Output Drive: ±24 mA at 3 V VCC
Broad VCC Operating Range: 1.65 V to 5.5 V
Matches Performance of LCX when Operated at 3.3 V VCC
Power Down High−Impedance Inputs / Outputs
Over−Voltage Tolerance Inputs Facilitate 5 V to 3 V Translation
Proprietary Noise / EMI Reduction Circuitry
Ultra−Small MicroPak™ Packages
Space−Saving SC−88 Package
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
A5, Z17
KK
XY
Z
M
•
= Specific Device Code
= 2−Digit Lot Run Traceability Code
= 2−Digit Date Code Format
= Assembly Plant Code
= Date Code
= Pb−Free Package
(Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering, marking and shipping information in the
package dimensions section on page 6 of this data sheet.
IEEC / IEC
A1
1
Y1
A2
1
Y2
Figure 1. Logic Symbol
© Semiconductor Components Industries, LLC, 1999
March, 2022 − Rev. 5
1
Publication Order Number:
NC7WZ17/D
NC7WZ17
Pin Configurations
A1 1
6
Y1
GND 2
5
VCC
A2 3
4
Y2
A1 1
GND 2
A2 3
Figure 2. SC−88 (Top View)
6 Y1
5 VCC
4 Y2
Figure 3. MicroPak (Top Through View)
AAA
Pin One
NOTES:
1. AAA represents Product Code Top Mark (see ordering code).
2. Orientation of Top Mark determines Pin One location. Read the
top product code mark left to right, Pin One is the lower left pin.
Figure 4. SC−88 Pin 1 Orientation
PIN DEFINITIONS
FUNCTION TABLE (Y = A)
Pin # SC70
Pin # MicroPak
Name
1
1
A1
Inputs
Output
Input
2
2
GND
3
3
4
Description
A
Y
Ground
L
L
A2
Input
H
H
4
Y2
Output
5
5
VCC
6
6
Y1
H = HIGH Logic Level
L = LOW Logic Level
Supply Voltage
Output
www.onsemi.com
2
NC7WZ17
ABSOLUTE MAXIMUM RATINGS
Symbol
Min
Max
Unit
VCC
Supply Voltage
Parameter
−0.5
6.5
V
VIN
DC Input Voltage
−0.5
6.5
V
DC Output Voltage
−0.5
6.5
V
VOUT
IIK
DC Input Diode Current
VIN < 0 V
−
−50
mA
IOK
DC Output Diode Current
VOUT < 0 V
−
−50
mA
IOUT
DC Output Current
−
±50
mA
DC VCC or Ground Current
−
±100
mA
−65
+150
°C
ICC or IGND
TSTG
Storage Temperature Range
TJ
Junction Temperature Under Bias
−
+150
°C
TL
Junction Lead Temperature (Soldering, 10 Seconds)
−
+260
°C
PD
Power Dissipation in Still Air
SC−88
−
332
mW
MicroPak−6
−
812
MicroPak2™−6
−
812
Human Body Model, JEDEC: JESD22−A114
−
4000
Charge Device Model, JEDEC: JESD22−C101
−
2000
ESD
V
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
VIN
VOUT
Parameter
Conditions
Min
Max
Unit
Supply Voltage Operating
1.65
5.50
V
Supply Voltage Data Retention
1.50
5.5
0
5.5
Input Voltage
Output Voltage
TA
Operating Temperature
qJA
Thermal Resistance
V
0
VCC
V
−40
+85
°C
SC−88
−
377
°C/W
MicroPak−6
−
154
MicroPak2−6
−
154
°C/W
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
3. Unused inputs must be held HIGH or LOW. They may not float.
DC ELECTICAL CHARACTERISTICS
TA = 25°C
TA = −40 to 85°C
Min
Typ
Max
Min
Max
Unit
1.65
−
1.00
1.40
−
1.40
V
1.80
−
1.07
1.50
−
1.50
2.30
−
1.38
1.80
−
1.80
3.00
−
1.74
2.20
−
2.20
4.50
−
2.43
3.10
−
3.10
5.50
−
2.88
3.60
−
3.60
Symbol
Parameter
VCC (V)
VP
Positive Threshold Voltage
Conditions
www.onsemi.com
3
NC7WZ17
DC ELECTICAL CHARACTERISTICS (continued)
TA = −40 to 85°C
TA = 25°C
Min
Typ
Max
Min
Max
Unit
1.65
0.20
0.50
−
0.20
−
V
1.80
0.25
0.56
−
0.25
−
2.30
0.40
0.75
−
0.40
−
3.00
0.60
0.98
−
0.60
−
4.50
1.00
1.42
−
1.00
−
5.50
1.20
1.68
−
1.20
−
1.65
0.10
0.48
0.90
0.10
0.90
1.80
0.15
0.51
1.00
0.15
1.00
2.30
0.25
0.62
1.10
0.25
1.10
3.00
0.40
0.76
1.20
0.40
1.20
4.50
0.60
1.01
1.50
0.60
1.50
5.50
0.70
1.20
1.70
0.70
1.70
1.55
1.65
−
1.55
−
1.70
1.80
−
1.70
−
2.30
2.20
2.30
−
2.20
−
3.00
2.90
3.00
−
2.90
−
Symbol
Parameter
VCC (V)
VN
Negative Threshold Voltage
VH
VOH
Hysteresis Voltage
HIGH Level Output Voltage
1.65
1.80
Conditions
VIN = VP or VN,
IOH = −100 mA
4.50
VOL
LOW Level Output Voltage
4.40
4.50
−
4.40
−
1.65
IOH= −4 mA
1.29
1.52
−
1.29
−
2.30
IOH= −8 mA
1.90
2.14
−
1.90
−
3.00
IOH= −16 mA
2.40
2.75
−
2.40
−
3.00
IOH= −24 mA
2.30
2.62
−
2.30
−
4.50
IOH= −32 mA
3.80
4.13
−
3.80
−
1.65
VIN = VP or VN,
IOL = 100 mA
−
0.00
0.10
−
0.10
1.80
IIN
Input Leakage Current
IOFF
Power Off Leakage Current
ICC
Quiescent Supply Current
−
0.00
0.10
−
0.10
2.30
−
0.00
0.10
−
0.10
3.00
−
0.00
0.10
−
0.10
4.50
−
0.00
0.10
−
0.10
V
V
V
1.65
IOL = 4 mA
−
0.08
0.24
−
0.24
2.30
IOL = 8 mA
−
0.10
0.30
−
0.30
3.00
IOL = 16 mA
−
0.16
0.40
−
0.40
3.00
IOL = 24 mA
−
0.24
0.55
−
0.55
4.50
IOL = 32 mA
−
0.25
0.550
−
0.55
VIN = 5.5 V, GND
−
−
±0.1
−
±1.0
mA
VIN or VOUT = 5.5 V
−
−
1
−
10
mA
VIN = 5.5 V, GND
−
−
1
−
10
mA
1.65 to 5.5
0
1.65 to 5.50
www.onsemi.com
4
NC7WZ17
AC ELECTRICAL CHARACTERISTICS
TA = 25°C
Symbol
tPLH, tPHL
Parameter
VCC (V)
Propagation Delay
(Figure 5, 6)
Typ
Max
Min
Max
Unit
−
8.3
14.3
−
15.8
ns
−
6.9
11.9
−
13.1
2.50 ±0.20
−
4.8
8.2
−
9.0
3.30 ±0.30
−
3.7
5.6
−
6.2
5.00 ±0.50
−
3.0
4.7
−
5.2
−
4.3
6.6
−
7.3
−
3.6
5.6
−
6.2
0
−
2.5
−
−
−
pF
3.30
−
10.0
−
−
−
pF
5.00
−
12.0
−
−
−
CL = 15 pF,
RL = 1 MW
1.80
3.30 ±0.30
5.00 ±0.50
Input Capacitance
CPD
Power Dissipation Capacitance
(Note 4) (Figure 7)
TA = −40 to 85°C
Min
1.65
CIN
Conditions
CL = 50 pF,
RL = 500 W
4. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at
no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression:
ICCD = (CPD) (VCC) (fIN) + (ICCstatic).
tr = 3 ns
VCC
VCC
90%
OUTPUT
CL
10%
GND
RL
NOTE:
5. CL includes load and stray capacitance;
Input PRR = 1.0 MHz, tW = 500 ns
90%
50%
INPUT
INPUT
tf = 3 ns
VOH
50%
tW
tPLH
tPHL
50%
OUTPUT
VOL
Figure 5. AC Test Circuit
Figure 6. AC Waveforms
VCC
A
INPUT
NOTE:
6. Input = AC Waveform; tr = tf = 1.8 ns;
PRR = 10 MHz; Duty Cycle = 50%.
Figure 7. ICCD Test Circuit
www.onsemi.com
5
10%
50%
NC7WZ17
DEVICE ORDERING INFORMATION
Top Mark
Packages
Shipping†
NC7WZ17P6X
Z17
6−Lead SC70, EIAJ SC−88, 1.25 mm Wide
3000 / Tape & Reel
NC7WZ17P6X−L22347
Z17
6−Lead SC70, EIAJ SC−88, 1.25 mm Wide
3000 / Tape & Reel
NC7WZ17L6X
A5
6−Lead MicroPak, 1.00 mm Wide
5000 / Tape & Reel
NC7WZ17L6X−L22175
A5
6−Lead MicroPak, 1.00 mm Wide
5000 / Tape & Reel
NC7WZ17FHX
A5
6−Lead, MicroPak2, 1x1 mm Body, .35 mm Pitch
5000 / Tape & Reel
NC7WZ17FHX−L22175
A5
6−Lead, MicroPak2, 1x1 mm Body, .35 mm Pitch
5000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MicroPak and MicroPak2 are trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United
States and/or other countries.
www.onsemi.com
6
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SIP6 1.45X1.0
CASE 127EB
ISSUE O
DOCUMENT NUMBER:
DESCRIPTION:
98AON13590G
SIP6 1.45X1.0
DATE 31 AUG 2016
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SC−88 (SC−70 6 Lead), 1.25x2
CASE 419AD
ISSUE A
DATE 07 JUL 2010
1
D
e
e
E1 E
SYMBOL
MIN
A
0.80
MAX
1.10
A1
0.00
0.10
A2
0.80
1.00
b
0.15
0.30
0.18
c
0.10
D
1.80
2.00
2.20
E
1.80
2.10
2.40
E1
1.15
1.25
1.35
0.65 BSC
e
L
0.26
L1
0.36
0.46
0.42 REF
0.15 BSC
L2
TOP VIEW
NOM
θ
0º
8º
θ1
4º
10º
q1
A2 A
q
b
q1
L
L1
A1
SIDE VIEW
c
L2
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-203.
DOCUMENT NUMBER:
DESCRIPTION:
98AON34266E
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
SC−88 (SC−70 6 LEAD), 1.25X2
PAGE 1 OF 1
onsemi and
are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves
the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SC−88/SC70−6/SOT−363
CASE 419B−02
ISSUE Y
1
SCALE 2:1
DATE 11 DEC 2012
2X
aaa H D
D
H
A
D
6
5
GAGE
PLANE
4
1
2
L
L2
E1
E
DETAIL A
3
aaa C
2X
bbb H D
2X 3 TIPS
e
B
6X
b
ddd
TOP VIEW
C A-B D
M
A2
DETAIL A
A
6X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH,
PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.20 PER END.
4. DIMENSIONS D AND E1 AT THE OUTERMOST EXTREMES OF
THE PLASTIC BODY AND DATUM H.
5. DATUMS A AND B ARE DETERMINED AT DATUM H.
6. DIMENSIONS b AND c APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.08 AND 0.15 FROM THE TIP.
7. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 TOTAL IN
EXCESS OF DIMENSION b AT MAXIMUM MATERIAL CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OF THE FOOT.
ccc C
A1
SIDE VIEW
C
SEATING
PLANE
END VIEW
c
RECOMMENDED
SOLDERING FOOTPRINT*
6X
DIM
A
A1
A2
b
C
D
E
E1
e
L
L2
aaa
bbb
ccc
ddd
MILLIMETERS
MIN
NOM MAX
−−−
−−−
1.10
0.00
−−−
0.10
0.70
0.90
1.00
0.15
0.20
0.25
0.08
0.15
0.22
1.80
2.00
2.20
2.00
2.10
2.20
1.15
1.25
1.35
0.65 BSC
0.26
0.36
0.46
0.15 BSC
0.15
0.30
0.10
0.10
GENERIC
MARKING DIAGRAM*
6
XXXMG
G
6X
0.30
INCHES
NOM MAX
−−− 0.043
−−− 0.004
0.035 0.039
0.008 0.010
0.006 0.009
0.078 0.086
0.082 0.086
0.049 0.053
0.026 BSC
0.010 0.014 0.018
0.006 BSC
0.006
0.012
0.004
0.004
MIN
−−−
0.000
0.027
0.006
0.003
0.070
0.078
0.045
0.66
1
2.50
0.65
PITCH
XXX = Specific Device Code
M
= Date Code*
G
= Pb−Free Package
(Note: Microdot may be in either location)
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
*Date Code orientation and/or position may
vary depending upon manufacturing location.
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
STYLES ON PAGE 2
DOCUMENT NUMBER:
DESCRIPTION:
98ASB42985B
SC−88/SC70−6/SOT−363
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 2
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
SC−88/SC70−6/SOT−363
CASE 419B−02
ISSUE Y
DATE 11 DEC 2012
STYLE 1:
PIN 1. EMITTER 2
2. BASE 2
3. COLLECTOR 1
4. EMITTER 1
5. BASE 1
6. COLLECTOR 2
STYLE 2:
CANCELLED
STYLE 3:
CANCELLED
STYLE 4:
PIN 1. CATHODE
2. CATHODE
3. COLLECTOR
4. EMITTER
5. BASE
6. ANODE
STYLE 5:
PIN 1. ANODE
2. ANODE
3. COLLECTOR
4. EMITTER
5. BASE
6. CATHODE
STYLE 6:
PIN 1. ANODE 2
2. N/C
3. CATHODE 1
4. ANODE 1
5. N/C
6. CATHODE 2
STYLE 7:
PIN 1. SOURCE 2
2. DRAIN 2
3. GATE 1
4. SOURCE 1
5. DRAIN 1
6. GATE 2
STYLE 8:
CANCELLED
STYLE 9:
PIN 1. EMITTER 2
2. EMITTER 1
3. COLLECTOR 1
4. BASE 1
5. BASE 2
6. COLLECTOR 2
STYLE 10:
PIN 1. SOURCE 2
2. SOURCE 1
3. GATE 1
4. DRAIN 1
5. DRAIN 2
6. GATE 2
STYLE 11:
PIN 1. CATHODE 2
2. CATHODE 2
3. ANODE 1
4. CATHODE 1
5. CATHODE 1
6. ANODE 2
STYLE 12:
PIN 1. ANODE 2
2. ANODE 2
3. CATHODE 1
4. ANODE 1
5. ANODE 1
6. CATHODE 2
STYLE 13:
PIN 1. ANODE
2. N/C
3. COLLECTOR
4. EMITTER
5. BASE
6. CATHODE
STYLE 14:
PIN 1. VREF
2. GND
3. GND
4. IOUT
5. VEN
6. VCC
STYLE 15:
PIN 1. ANODE 1
2. ANODE 2
3. ANODE 3
4. CATHODE 3
5. CATHODE 2
6. CATHODE 1
STYLE 16:
PIN 1. BASE 1
2. EMITTER 2
3. COLLECTOR 2
4. BASE 2
5. EMITTER 1
6. COLLECTOR 1
STYLE 17:
PIN 1. BASE 1
2. EMITTER 1
3. COLLECTOR 2
4. BASE 2
5. EMITTER 2
6. COLLECTOR 1
STYLE 18:
PIN 1. VIN1
2. VCC
3. VOUT2
4. VIN2
5. GND
6. VOUT1
STYLE 19:
PIN 1. I OUT
2. GND
3. GND
4. V CC
5. V EN
6. V REF
STYLE 20:
PIN 1. COLLECTOR
2. COLLECTOR
3. BASE
4. EMITTER
5. COLLECTOR
6. COLLECTOR
STYLE 21:
PIN 1. ANODE 1
2. N/C
3. ANODE 2
4. CATHODE 2
5. N/C
6. CATHODE 1
STYLE 22:
PIN 1. D1 (i)
2. GND
3. D2 (i)
4. D2 (c)
5. VBUS
6. D1 (c)
STYLE 23:
PIN 1. Vn
2. CH1
3. Vp
4. N/C
5. CH2
6. N/C
STYLE 24:
PIN 1. CATHODE
2. ANODE
3. CATHODE
4. CATHODE
5. CATHODE
6. CATHODE
STYLE 25:
PIN 1. BASE 1
2. CATHODE
3. COLLECTOR 2
4. BASE 2
5. EMITTER
6. COLLECTOR 1
STYLE 26:
PIN 1. SOURCE 1
2. GATE 1
3. DRAIN 2
4. SOURCE 2
5. GATE 2
6. DRAIN 1
STYLE 27:
PIN 1. BASE 2
2. BASE 1
3. COLLECTOR 1
4. EMITTER 1
5. EMITTER 2
6. COLLECTOR 2
STYLE 28:
PIN 1. DRAIN
2. DRAIN
3. GATE
4. SOURCE
5. DRAIN
6. DRAIN
STYLE 29:
PIN 1. ANODE
2. ANODE
3. COLLECTOR
4. EMITTER
5. BASE/ANODE
6. CATHODE
STYLE 30:
PIN 1. SOURCE 1
2. DRAIN 2
3. DRAIN 2
4. SOURCE 2
5. GATE 1
6. DRAIN 1
Note: Please refer to datasheet for
style callout. If style type is not called
out in the datasheet refer to the device
datasheet pinout or pin assignment.
DOCUMENT NUMBER:
DESCRIPTION:
98ASB42985B
SC−88/SC70−6/SOT−363
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 2 OF 2
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
UDFN6 1.0X1.0, 0.35P
CASE 517DP
ISSUE O
DOCUMENT NUMBER:
DESCRIPTION:
98AON13593G
UDFN6 1.0X1.0, 0.35P
DATE 31 AUG 2016
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
工商网监
湘ICP备2023018690号
