NCP171AMX120100TCG

LDO Regulator - Ultra-Low Iq, Dual Power Mode 50nA, 80mA NCP171 The NCP171 is a Dual mode LDO offering up to 80 mA in Active Mode and as low as 50 nA of Iq in Low Power Mode. The Dual Mode function is selectable with the ECO pin allowing for dynamic switching between Active and Low Power Modes, ideal in long life battery powered applications. The output Voltage in Low Power mode can be lowered by an internally factory programmed value ranging 50 mV, 100 mV, 150 mV or 200 mV with respect to the nominal output voltage in Active Mode. This feature further lowers the application consumption in sleep mode. The NCP171 is in the SLIQ (Super Low Iq) LDO family and is available in small XDFN4 1.2 x 1.2 package. Features • • • • • • • • • • • • • Operating Input Voltage Range: 1.7 V to 5.5 V Output Voltage Range: 0.6 V to 3.3 V (50 mV steps) Low Power Mode / Active Mode Externally Controlled by ECO pin Internally Factory Programmable Output Voltage Offset for Low Power/Active Mode to 50 mV, 100 mV, 150 mV, 200 mV Quiescent Current of 50 nA at No Load, (Low Power mode) Maximum Current 80 mA in Active Mode and 5 mA in Low Power Mode Low Dropout: 41 mV Typ. at 80 mA (Vout = 3.3 V) ±2% Output Voltage Accuracy in Active Mode High PSRR: 65 dB at 1 kHz in Active Mode Active Output Discharge for Fast Output Turn−Off Current Limitation, Thermal Shutdown Available in Small XDFN4 1.2x1.2 Package These are Pb−Free Devices www.onsemi.com 1 XDFN4 1.2x1.2 AM SUFFIX CASE 711BC MARKING DIAGRAM XXM 1 XX = Specific Device Code M = Date Code PIN CONNECTIONS ENA 4 3 IN 2 OUT GND ECO 1 (Top View) Typical Applications • • • • IoT RFID Portable Communication Equipment Consumer Electronics ORDERING INFORMATION See detailed ordering, marking and shipping information on page 20 of this data sheet. Figure 1. Typical Application Schematic © Semiconductor Components Industries, LLC, 2018 December, 2019 − Rev. 2 1 Publication Order Number: NCP171/D NCP171 Active Mode part ECO Current Limit & Thermal Shutdown Low Power part Vin Vout Active Discharge Vref Voltage Scaling ENA GND Figure 2. Simplified Schematic Block Diagram Table 1. PIN FUNCTION DESCRIPTION Pin No. XDFN4 Pin Name Description 1 ECO Low Power and Active mode control pin. Pulling this pin to ground switches the device into Low Power mode and pushing this pin to output voltage switches the device into Active mode. 2 OUT Output pin 3 IN 4 ENA Enable pin. Driving ENA above 1.2 V turns on the regulator. Driving ENA below 0.4 V puts the regulator into shutdown mode. 5(EP) GND Ground Input pin www.onsemi.com 2 NCP171 Table 2. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit VIN 6.0 V Output Voltage VOUT −0.3 to VIN V Enable pin VENA −0.3 to VIN V ECO pin VECO −0.3 to VIN V Output Current IOUT 120 mA PD 400 mW TJ(MAX) 85 °C TSTG −55 to 125 °C ESD Capability, Human Body Model (Note 2) ESDHBM 2000 V ESD Capability, Machine Model (Note 2) ESDMM 200 V Input Voltage (Note 1) Power Dissipation XDFN4 Maximum Junction Temperature Storage Temperature Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114) ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115) Latchup Current Maximum Rating tested per JEDEC standard: JESD78 Table 3. THERMAL CHARACTERISTICS (Note 3) Rating Thermal Characteristics, XDFN4 Thermal Resistance, Junction−to−Air Symbol Value Unit RqJA 170 °C/W 3. This data was derived by thermal simulations for a single device mounted on the 40 mm x 40 mm x 1.6 mm FR4 PCB with 2−ounce 800 sq mm copper area on top and bottom. www.onsemi.com 3 NCP171 Table 4. ELECTRICAL CHARACTERISTICS −40°C ≤ TJ ≤ 85°C; VIN = VOUTNOM + 0.5 V or 1.7 V, whichever is greater; IOUT = 100 mA at Low Power Mode / 1 mA at Active Mode, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 4) Parameter Test Conditions Operating Input Voltage Output Voltage Load Regulation Min Max Unit VIN 1.7 Typ 5.5 V VOUTAC = VOUTLP + VOFFSET x0.97 x1.03 V −40°C ≤ TJ ≤ 85°C, IOUT < 5 mA Low Power Mode (LP) ECO = 0 NCP171A3MXxxxyyy −40°C ≤ TJ ≤ 85°C, IOUT < 5 mA Low Power Mode (LP) ECO = 0 NCP171AMXxxxyyy x0.95 x1.05 V TJ = +25°C, 0 ≤ IOUT