NCV7601

NCV7601 Quad Driver This automotive grade product provides a versatile interface between control logic and many types of loads. The inputs accept a wide range of control signal levels while the open−collector outputs feature independent thermal and current limiting. Integral transient suppression diodes are provided at all inputs and outputs. http://onsemi.com Features • • • • • • • • • • • • • Operation in −40°C − 125°C Environment TTL/DTL/CMOS Compatible Inputs NAND Logic with Common Enable VCEX ≥ 60 V, VCE(SUS) ≥ 40 V VCE(SAT) ≤ 650 mV @ IC = 600 mA Thermally Efficient Fused−Lead Package Pin Compatible with: − CA3242/CA3262 − UDx2543/UDx2549/UDx2559 − L6220/L6221/L9222 Pb−Free Package is Available* 1 PDIP−16 P SUFFIX CASE 648 MARKING DIAGRAM Typical Applications Body and Drivetrain Electronics Incandescent Lamp/LED Loads Solenoid/Relay/Inductor Loads Heater/Resistor Loads Stepper/DC Motor Loads 16 NCV7601P AWLYYWWG 1 ABSOLUTE MAXIMUM RATINGS Rating VCC Logic Input Voltage (INA, INB, INC, IND, ENABLE) Power Output (OUTA, OUTB, OUTC, OUTD) Junction Temperature Range, TJ Storage Temperature Range ESD Susceptibility (Human Body Model) Package Thermal Resistance Junction−to−Case, RqJC Junction−to−Ambient, RqJA Lead Temperature Soldering: Wave Solder (through hole styles only) (Note 1) Value −0.3 to 7.0 −0.3 to 15 −0.3 to 60 −40 to 150 −55 to 150 2.0 15 50 260 peak Unit V V V °C °C kV °C/W °C/W °C A WL YY WW G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package PIN CONNECTIONS 1 OUTA CLAMPAB OUTB GND GND OUTC CLAMPCD OUTD 16 INA INB ENABLE GND GND VCC INC IND Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. 10 second maximum. ORDERING INFORMATION Device NCV7601P Package PDIP−16 PDIP−16 (Pb−Free) Shipping 25 Units/Rail 25 Units/Rail *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 NCV7601PG 1 April, 2006 − Rev. 4 Publication Order Number: NCV7601/D NCV7601 +14 V NCV7601 1 16 A 2 15 Heater 3 B ENA 14 4 13 Controller 5 12 VCC Solenoid or Relay 30 V 7 6 +5.0 V 11 C 10 194 Lamp 8 D 9 Figure 1. Typical Driver Applications ELECTRICAL CHARACTERISTICS (4.0 V ≤ VCC ≤ 5.5 V, −40°C ≤ TJ ≤ 125°C, unless otherwise specified.) Note 2 Characteristic GENERAL VCC Supply Current Outputs Off, VCC = 5.5 V Note 3 IOUT = 600 mA, VCC = VIN = 5.5 V (four outputs on) (one output on) − − − − − − 5.0 65 20 mA mA mA Test Conditions Min Typ Max Unit OUTPUT DRIVERS Saturation Voltage Leakage Current Current Limit Thermal Shutdown Sustaining Voltage, VCE(SUS) CLAMP DIODES Forward Voltage Leakage Current INPUT Input Current Input High Voltage Input Low Voltage AC CHARACTERISTICS (Note 4) Turn−On Delay, Turn−Off Delay IOUT = 500 mA − − 10 ms 2. Designed to meet these characteristics over the stated temperature range, though may not be 100% parametrically tested in production. 3. Pulse test. 4. Input rise time ≤ 10 ns, falltime ≤ 10 ns, measured at 50% points. 0 V ≤ VIN ≤ VCC IOUT = 600 mA IOUT = 600 mA −2.0 2.0 − − − − 10 − 0.8 mA V V IF = 1.5 A, VCC = 5.5 V VR = 60 V, VCC = 5.5 V − − − − 2.0 100 V mA IOUT = 600 mA, VIN = 2.0 V, VCC = 4.0 V VOUT = 60 V, VIN = 0.8 V, VCC = 5.5 V 4.5 V < VOUT < 16 V, VCC = 5.0 V − VCC = 5.5 V − − − 150 40 − − − 180 − 650 50 1.8 210 − mV mA A °C V http://onsemi.com 2 NCV7601 PACKAGE PIN DESCRIPTION PACKAGE PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PIN SYMBOL OUTA CLAMPAB OUTB GND GND OUTC CLAMPCD OUTD IND INC VCC GND GND ENABLE INB INA Driver A Output Diode Clamp to Driver A and Driver B Driver B Output Ground Ground Driver C Output Diode Clamp to Driver C and Driver D Driver D Output Driver D Input Driver C Input 5.0 V Input Supply Voltage Ground Ground ENABLE Input to all Drivers Driver B Input Driver A Input FUNCTION VCC OUTX = INX • ENA Thermal Limit + − Predriver DT J CLAMP OUTx INx Current Limit ENABLE + 18 V 18 V V 1.35 V − D I