NCV8606

NCV8605, NCV8606 500 mA, Low IGND, CMOS LDO Regulator with/without Enable and with Enhanced ESD Protection The NCV8605/NCV8606 provide in excess of 500 mA of output current at fixed voltage options or an adjustable output voltage from 5.0 V down to 1.25 V. These devices are designed for space constrained and portable battery powered applications and offer additional features such as high PSRR, low noise operation, short circuit and thermal protection. The devices are designed to be used with low cost ceramic capacitors and are packaged in the DFN6 3x3.3. NCV8605 is designed without enable pin, NCV8606 is designed with enable pin. Features http://onsemi.com MARKING DIAGRAM 1 DFN6, 3x3.3 MN SUFFIX CASE 506AX x zzz A Y WW G V860x zzz AYWWG G • Output Voltage Options: • • • • • • • • • • • • • • Adjustable, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V Adjustable Output by External Resistors from 5.0 V down to 1.25 V Current Limit 675 mA Low IGND (Independent of Load) $1.5% Output Voltage Tolerance Over All Operating Conditions (Adjustable) $2% Output Voltage Tolerance Over All Operating Conditions (Fixed) NCV8605 Fixed is Direct Replacement LP8345 Typical Noise Voltage of 50 mVrms without a Bypass Capacitor Enhanced ESD Ratings: 4 kV Human Body Mode (HBM) 400 V Machine Model (MM) NCV Prefix for Automotive and Other Applications Requiring Site and Change Controls These are Pb−Free Devices Hard Disk Drivers Notebook Computers Battery Power Electronics Portable Instrumentation = 5 or 6 = ADJ, 150, 180, 250, 280, 300, 330, 500 = Assembly Location = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) NCV8605 PIN CONNECTIONS DFN6 3x3.3mm Vin GND NC 1 2 3 (Top View) GND 6 5 4 Vin SENSE/ADJ Vout Typical Applications NCV8606 PIN CONNECTIONS DFN6 3x3.3mm Vin GND Vin Cin Vin NCV8605 (Fixed) SENSE GND Vout Cout Vout EN 1 2 3 (Top View) GND 6 5 4 Vin SENSE/ADJ Vout ORDERING INFORMATION Figure 1. NCV8605 Typical Application Circuit for Fixed Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V) See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. © Semiconductor Components Industries, LLC, 2010 May, 2010 − Rev. 0 1 Publication Order Number: NCV8605/D NCV8605, NCV8606 Vin Cin Vin NCV8606 (Fixed) EN SENSE GND Vout Cout Vout Figure 2. NCV8606 Typical Application Circuit for Fixed Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V) Vin Cin Vin Vout NCV8605 (Adjustable) GND ADJ Vout R1 Cout Vin Cin Vin Vout NCV8606 (Adjustable) GND ADJ Vout Cout EN R1 R2 R2 Figure 3. NCV8605 Typical Application Circuit for Adjustable Version (1.25 V < Vout v 5.0 V) Figure 4. NCV8606 Typical Application Circuit for Adjustable Version (1.25 V < Vout v 5.0 V) Vin Cin Vin Vout Cout Vout Vin Cin Vin Vout Cout Vout NCV8605 (Adjustable) GND ADJ NCV8606 (Adjustable) EN GND ADJ Figure 5. NCV8605 Typical Application Circuit for Adjustable Version (Vout = 1.25 V) Figure 6. NCV8606 Typical Application Circuit for Adjustable Version (Vout = 1.25 V) Vin Adjustable Version Only Driver with Current Limit Thermal Shutdown + − Vref Vout Vin Adjustable Version Only Driver with Current Limit Thermal Shutdown EN + − Vref Vout SENSE/ADJ SENSE/ADJ GND Fixed Version Only GND Fixed Version Only Figure 7. NCV8605 Simplified Block Diagram Figure 8. NCV8606 Simplified Block Diagram http://onsemi.com 2 NCV8605, NCV8606 PIN FUNCTION DESCRIPTION Pin No. 1 2 3 4 5 Pin Name Vin GND NC/EN Vout SENSE/ADJ Positive Power Supply Input* Power Supply Ground NCV8605: This Pin is Not Connected NCV8606: This Pin is Enable Input, Active HIGH Regulated Output Voltage Output Voltage Sense Input Fixed Version: Connect Directly to Output Capacitor Adjustable Version: Connect to Middle Point of External Resistor Divider Positive Power Supply Input* Exposed Pad is Connected to Ground Description 6 EPAD Vin GND *Pins 1 and 6 must be connected together externally for output current full range operation ABSOLUTE MAXIMUM RATINGS Rating Input Voltage Range (Note 1) Chip Enable Voltage Range (NCV8606 only) Output Voltage Range Output Voltage/Sense Input Range, SENSE/ADJ ESD Capability Maximum Junction Temperature Storage Temperature Range Human Body Model Machine Model Symbol Vin VEN Vout VADJ ESD TJ(MAX) TSTG Value −0.3 to 6.5 −0.3 to 6.5 −0.3 to 6.5 −0.3 to 6.5 4000 400 150 −65 to 150 Unit V V V V V °C °C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. NOTE: This device series contains ESD Protection and exceeds the following tests: ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114) ESD Machine Model tested per AEC− 150 mA per JEDEC standard: JESD78Q100−003 (EIA/JESD22−A115) Latchup Current Maximum Rating: v 150 mA per JEDEC standard: JESD78. 1. Minimum Vin = (Vout + VDO) or 1.5 V, whichever is higher. THERMAL CHARACTERISTICS Rating Thermal Resistance, Junction−to−Ambient (Note 2) Thermal Resistance, Junction−to−Case Symbol RqJA RYJC Value 75 18 Unit °C/W °C/W 2. Soldered on 645 mm2, 1 oz copper area, FR4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. OPERATING RANGES (Note 3) Rating Input Voltage (Note 4) Output Current (Notes 5 and 6) Junction Temperature Ambient Temperature 3. 4. 5. 6. Symbol Vin Iout TJ TA Value 1.5 to 6.0 0 to 675 −40 to 150 −40 to 125 Unit V mA °C °C Refer to Electrical Characteristics and Application Information for Safe Operating Area. Minimum Vin = (Vout + VDO) or 1.5 V, whichever is higher. Minimum limit valid for fixed versions only. For more details refer to Application Information Section. Maximum limit for Vout = Vout(nom) − 10%. http://onsemi.com 3 NCV8605, NCV8606 ELECTRICAL CHARACTERISTICS Vin = (Vout + 0.5 V) or 1.5 V, whichever is higher, Cin = 1 mF, Cout = 1 mF, for typical values TA = 25°C, for min/max values TA = −40°C to 85°C; unless otherwise noted. (Notes 9 and 10) Parameter Output voltage (Adjustable Version) Output voltage (Fixed Versions) Test Conditions Vin = 1.75 V to 6 V Iout = 1 mA to 500 mA 1.5 V Vin = (Vout + 0.5 V) to 6 V 1.8 V Iout = 1 mA to 500 mA 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V Vin = (Vout + 0.5 V) to 6 V, Iout = 1 mA Iout = 1 mA to 500 mA VDO = Vin − Vout Vout = 1.25 V Iout = 500 mA VDO = Vin − (Vout − 0.1 V) 1.5 V Iout = 500 mA 1.8 V Vout = 0 V to 90% Vout(nom) 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V VEN = 0 V Iout = 1 mA to 500 mA Vout = Vout(nom) − 10 % Vout = 0 V Symbol Vout Vout Min 1.231 (−1.5%) 1.470 1.764 2.450 2.744 2.940 3.234 4.900 (−2%) − − − Typ 1.250 1.5 1.8 2.5 2.8 3.0 3.3 5.0 4 10 450 Max 1.269 (+1.5%) 1.530 1.836 2.550 2.856 3.060 3.366 5.100 (+2%) 10 30 470 Unit V V Line regulation Load regulation Dropout voltage (Adjustable Version) (Note 9) Dropout voltage (Fixed Version) Regline Regload VDO mV mV mV VDO − − − − − − − − − 675 700 290 250 200 190 180 170 150 0.1 145 − 1000 360 300 250 240 230 220 200 1 180 − 1350 mV Disable Current (NCV8606 Only) (Note 10) Ground Current Current Limit (Note 11) Output Short Circuit Current Enable Input Threshold Voltage (NCV8606 Only) Voltage Increasing, Logic High Voltage Decreasing, Logic Low Turn−on Time (Note 11) IDIS IGND ILIM ISC Vth(EN) mA mA mA mA V High Low Vin = 0 V to (Vout + 0.5 V) or 1.75 V, 1.25 V whichever is higher 1.5 V Vout = 0 V to 90% of Vout(nom) 1.8 V 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V ton 0.9 − − − − − − − − − − − − − − − − − − − 6 6 7 8 10 12 15 30 12 12 13 16 18 19 20 30 − 0.4 − − − − − − − − − − − − − − − − ms Enable Time (NCV8606 Only) (Note 11) VEN = From 0 V to Vin 1.25 V 1.5 V 1.8 V 2.5 V 2.8 V 3.0 V 3.3 V 5.0 V tEN ms 7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area. 8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. Maximum dropout voltage is limited to minimum input voltage Vin = 1.7 V recommended for guaranteed operation at maximum output current. 10. Refer to application information section. 11. Values based on design and/or characterization. http://onsemi.com 4 NCV8605, NCV8606 ELECTRICAL CHARACTERISTICS Vin = (Vout + 0.5 V) or 1.5 V, whichever is higher, Cin = 1 mF, Cout = 1 mF, for typical values TA = 25°C, for min/max values TA = −40°C to 85°C; unless otherwise noted. (Notes 9 and 10) Parameter Power Supply Ripple Rejection (Note 11) Test Conditions Iout = 500 mA Vout = 1.25 V Vin − Vout = 1 V f = 120 Hz, 0.5 VPP f = 1 kHz, 0.5 VPP f = 10 kHz, 0.5 VPP f = 10 Hz to 100 kHz, Vout = 1.25 V Symbol PSRR − − − Vn TSD TSH − − − 62 55 40 50 175 10 − − − − − − mVrms °C °C Min Typ Max Unit dB Output Noise Voltage (Note 11) Thermal Shutdown Temperature (Note 11) Thermal Shutdown Hysteresis (Note 11) 7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area. 8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. Maximum dropout voltage is limited to minimum input voltage Vin = 1.7 V recommended for guaranteed operation at maximum output current. 10. Refer to application information section. 11. Values based on design and/or characterization. http://onsemi.com 5 NCV8605, NCV8606 TYPICAL CHARACTERISTICS 1.267 1.264 1.261 1.258 1.255 1.252 1.249 1.246 1.243 1.240 1.237 1.234 1.231 −40 Vin = Vout + 0.5 V = 1.75 V Vin = 6.0 V 2.55 Vout, OUTPUT VOLTAGE (V) Vout = 1.25 V Iout = 1 mA 2.54 2.53 2.52 2.51 2.50 2.49 2.48 2.47 2.46 2.45 −40 −20 0 20 40 60 80 100 120 140 Vin = Vout + 0.5 V = 3.0 V Vin = 6.0 V Vout = 2.5 V Iout = 1 mA Vout, OUTPUT VOLTAGE (V) −20 0 20 40 60 80 100 120 140 TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C) Figure 9. Output Voltage vs. Temperature (Vout = 1.25 V) 5.10 VDO, DROPOUT VOLTAGE (mV) 5.08 Vout, OUTPUT VOLTAGE (V) 5.06 5.04 5.02 5.00 4.98 4.96 4.94 4.92 4.90 −40 −20 0 20 40 60 80 100 120 140 Vin = 6.0 V Vout = 5.0 V Iout = 1 mA Vin = Vout + 0.5 V = 5.5 V 300 270 240 210 180 150 120 90 60 30 0 −40 Figure 10. Output Voltage vs. Temperature (Vout = 2.5 V) Vout = 2.5 V Iout = 500 mA Iout = 300 mA Iout = 150 mA −20 0 20 40 60 80 100 120 140 TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C) Figure 11. Output Voltage vs. Temperature (Vout = 5.0 V) 200 VDO, DROPOUT VOLTAGE (mV) IGND, GROUND CURRENT (mA) 180 160 140 120 100 80 60 40 20 0 −40 −20 0 20 40 60 80 100 120 140 Iout = 500 mA Iout = 300 mA Iout = 150 mA Vout = 5.0 V 180 170 160 150 140 130 120 110 100 90 80 −40 Figure 12. Dropout Voltage vs. Temperature (Vout = 2.5 V) Vin = Vout + 0.5 V Iout = 500 mA Vout = 5.0 V Vout = 2.5 V Vout = 1.25 V −20 0 20 40 60 80 100 120 140 TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C) Figure 13. Dropout Voltage vs. Temperature (Vout = 5.0 V) Figure 14. Ground Current vs. Temperature http://onsemi.com 6 NCV8605, NCV8606 TYPICAL CHARACTERISTICS 1600 ISC, SHORT CIRCUIT CURRENT LIMIT (mA) 1400 1200 1000 800 600 400 200 −40 −20 0 20 40 60 80 100 120 140 Vin = 1.75 V Vout = 1.25 V Vin = 6.0 V PSRR (dB) 80 70 60 50 40 30 Vout = 1.25 V 20 Vin = 2.25 V Cout = 1.0 mF 10 T = 25°C A 0 10 100 1000 f, FREQUENCY (Hz) 10000 100000 Iout = 500 mA Iout = 1mA TA, AMBIENT TEMPERATURE (°C) Figure 15. Short Circuit Current Limit vs. Temperature (Vout = 1.25 V) 80 70 60 PSRR (dB) 50 40 30 20 10 0 10 Vout = 2.5 V Vin = 3.5 V Cout = 1.0 mF TA = 25°C 100 1000 f, FREQUENCY (Hz) 10000 Iout = 500 mA Iout = 1mA 1600 Vn, NOISE DENSITY (nV/√/HZ) 1400 1200 1000 800 600 400 200 0 10 Figure 16. PSRR vs. Frequency (Vout = 1.25 V) Vn = 47 mVrms Vin = Vout + 0.5 V = 1.75 V Cin = Cout = 1.0 mF Iout = 500 mA TA = 25°C 100000 100 1000 10000 100000 f, FREQUENCY (Hz) Figure 17. PSRR vs. Frequency (Vout = 2.5 V) 2500 Vn, NOISE DENSITY (nV/√/HZ) Vn = 70 mVrms 2000 1500 1000 500 0 10 Iout 500 mA/div Figure 18. Noise Density vs. Frequency (Vout = 1.25 V) Vin = Vout + 0.5 V = 3.0 V Cin = Cout = 1.0 mF Iout = 500 mA TA = 25°C Vout 200 mV/div Vin = 3.0 V Vout = 2.5 V Cout = 10 mF trise = tfall = 1 ms TA = 25°C 100 1000 f, FREQUENCY (Hz) 10000 100000 TIME (40 ms/div) Figure 19. Noise Density vs. Frequency (Vout = 2.5 V) Figure 20. Load Transient (Vout = 2.5 V) http://onsemi.com 7 NCV8605, NCV8606 TYPICAL CHARACTERISTICS Vout 100 mV/div Vout 1 V/div 4.0 V Vin = 2.5 V Iout = 500 mA Cout = 10 mF trise = tfall = 1 ms TA = 25°C Vin 1 V/div Vout = 2.5 V Iout = 0 mA Cout = 10 mF Vin 500 mV/div 3.0 V TIME (20 ms/div) Vin = 3.0 V trise = 1 ms TA = 25°C TIME (10 ms/div) Figure 21. Line Transient (Vout = 2.5 V) Figure 22. Startup Transient (Vout = 2.5 V) http://onsemi.com 8 NCV8605, NCV8606 DEFINITIONS General All measurements are performed using short pulse low duty cycle techniques to maintain junction temperature as close as possible to ambient temperature. Line Regulation current are kept constant during the measurement. Results are expressed in mVrms or nV / √Hz. Turn−on and Turn−off Times The change in output voltage for a change in input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average junction temperature is not significantly affected. Load Regulation The change in output voltage for a change in output load current at a constant temperature. Dropout Voltage Turn−on Time is time difference measured during power−up of the device from the moment when input voltage reaches 90% of its operating value to the moment when output voltage reaches 90% of its nominal value at specific output current or resistive load. Turn−off Time is time difference measured during power−down of the device from the moment when input voltage drops to 10% of its operating value to the moment when output voltage drops to 10% of its nominal value at specific output current or resistive load. Enable and Disable Times The input to output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. Measured when the output drops 100 mV below its nominal value. The junction temperature, load current, and minimum input supply requirements affect the dropout level. Ground and Disable Currents Ground Current is the current that flows through the ground pin when the regulator operates without a load on its output (IGND). This consists of internal IC operation, bias, etc. It is actually the difference between the input current (measured through the LDO input pin) and the output load current. If the regulator has an input pin that reduces its internal bias and shuts off the output (enable/disable function), this term is called the disable current (IDIS). Current Limit and Short Circuit Current Limit Enable Time is time difference measured during power−up of the device from the moment when enable voltage reaches 90% of input voltage operating value to the moment when output voltage reaches 90% of its nominal value at specific output current or resistive load. Disable Time is time difference measured during power−down of the device from the moment when enable voltage drops to 10% of input voltage operating value to the moment when output voltage drops to 10% of its nominal value at specific output current or resistive load. Line Transient Response Typical output voltage overshoot and undershoot response when the input voltage is excited with a given slope. Load Transient Response Current Limit is value of output current by which output voltage drops by 10% with respect to its nominal value. Short Circuit Current Limit is output current value measured with output of the regulator shorted to ground. PSRR Typical output voltage overshoot and undershoot response when the output current is excited with a given slope between no−load and full−load conditions. Thermal Protection Power Supply Rejection Ratio is defined as ratio of output voltage and input voltage ripple. It is measured in decibels (dB). Output Noise Voltage Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated at typically 175°C, the regulator turns off. This feature is provided to prevent failures from accidental overheating. Maximum Package Power Dissipation This is the integrated value of the output noise over a specified frequency range. Input voltage and output load The power dissipation level at which the junction temperature reaches its maximum operating value. http://onsemi.com 9 NCV8605, NCV8606 APPLICATIONS INFORMATION The NCV8605/NCV8606 regulator is self*protected with internal thermal shutdown and internal current limit. Typical application circuits are shown in Figures 1 to 4. Input Decoupling (Cin) Noise Decoupling A ceramic or tantalum 1.0 mF capacitor is recommended and should be connected close to the NCV8605/NCV8606 package. Higher capacitance and lower ESR will improve the overall line transient response. The NCV8605/NCV8606 is a low noise regulator and needs no external noise reduction capacitor. Unlike other low noise regulators which require an external capacitor and have slow startup times, the NCV8605/NCV8606 operates without a noise reduction capacitor, has a typical 8 ms turn−on time and achieves a 50 mVrms overall noise level between 10 Hz and 100 kHz. Enable Operation (NCV8606 Only) Output Decoupling (Cout) The NCV8605/NCV8606 is a stable component and does not require a minimum Equivalent Series Resistance (ESR) for the output capacitor. The minimum output decoupling value is 1.0 mF and can be augmented to fulfill stringent load transient requirements. The regulator works with ceramic chip capacitors as well as tantalum devices. Larger values improve noise rejection and load regulation transient response. Typical characteristics were measured with Murata ceramic capacitors. GRM219R71E105K (1 mF, 25 V, X7R, 0805) and GRM21BR71A106K (10 mF, 10 V, X7R, 0805). The enable pin will turn the regulator on or off. The threshold limits are covered in the electrical characteristics table in this data sheet. The turn−on/turn−off transient voltage being supplied to the enable pin should exceed a slew rate of 10 mV/ms to ensure correct operation. If the enable function is not to be used then the pin should be connected to Vin. Output Voltage Adjust No−Load Regulation Considerations The NCV8605/NCV8606 adjustable regulator will operate properly under conditions where the only load current is through the resistor divider that sets the output voltage. However, in the case where the NCV8605/NCV8606 is configured to provide a 1.250 V output, there is no resistor divider. If the part is enabled under no−load conditions, leakage current through the pass transistor at junction temperatures above 85°C can approach several microamps, especially as junction temperature approaches 150°C. If this leakage current is not directed into a load, the output voltage will rise up to a level approximately 20 mV above nominal. The NCV8605/ NCV8606 contains an overshoot clamp circuit to improve transient response during a load current step release. When output voltage exceeds the nominal by approximately 20 mV, this circuit becomes active and clamps the output from further voltage increase. Tying the ENABLE pin to Vin (NCV8606 only) will ensure that the part is active whenever the supply voltage is present, thus guaranteeing that the clamp circuit is active whenever leakage current is present. When the NCV8606 adjustable regulator is disabled, the overshoot clamp circuit becomes inactive and the pass transistor leakage will charge any capacitance on Vout. If no load is present, the output can charge up to within a few millivolts of Vin. In most applications, the load will present some impedance to Vout such that the output voltage will be inherently clamped at a safe level. A minimum load of 10 mA is recommended. Unlike LP8345, for NCV8605/606 fixed voltage versions there is no limitation for minimum load current. The output voltage can be adjusted from 1 times (Figure 4) to 4 times (Figure 3) the typical 1.250 V regulation voltage via the use of resistors between the output and the ADJ input. The output voltage and resistors are chosen using Equation 1 and Equation 2. V out + 1.250 1 ) R1 R2 R1 V ) I ADJ R1 (eq. 1) R2 ^ out 1.25 *1 (eq. 2) Input bias current IADJ is typically less than 150 nA. Choose R1 arbitrarily to minimize errors due to the bias current and to minimize noise contribution to the output voltage. Use Equation 2 to find the required value for R2. Thermal As power in the NCV8605/NCV8606 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. When the NCV8605/NCV8606 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power applications. The maximum dissipation the NCV8605/NCV8606 can handle is given by: P D(MAX) + T J(MAX) * T A R QJA (eq. 3) Since TJ is not recommended to exceed 125°C (TJ(MAX)), then the NCV8605/NCV8606 soldered on 645 mm2, 1 oz copper area, FR4 can dissipate up to 1.3 W when the ambient http://onsemi.com 10 NCV8605, NCV8606 temperature (TA) is 25°C. See Figure 23 for RqJA versus PCB area. The power dissipated by the NCV8605/NCV8606 can be calculated from the following equations: P D [ V in I GND@I OUT ) I out V in * V out (eq. 4) Hints or V in(MAX) [ 250 200 RqJA, (°C/W) 150 100 50 0 FR4 = 1.0 oz FR4 = 2.0 oz P D(MAX) ) V out I out ) I GND I out (eq. 5) Vin and GND printed circuit board traces should be as wide as possible. When the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. Place external components, especially the output capacitor, as close as possible to the NCV8605/NCV8606, and make traces as short as possible. 0 200 400 COPPER AREA 600 (mm2) 800 Figure 23. Thermal Resistance vs. Copper Area http://onsemi.com 11 NCV8605, NCV8606 ORDERING INFORMATION Device NCV8605MNADJT2G NCV8605MN15T2G NCV8605MN18T2G NCV8605MN25T2G NCV8605MN28T2G NCV8605MN30T2G NCV8605MN33T2G NCV8605MN50T2G NCV8606MNADJT2G NCV8606MN15T2G NCV8606MN18T2G NCV8606MN25T2G NCV8606MN28T2G NCV8606MN30T2G NCV8606MN33T2G NCV8606MN50T2G Nominal Output Voltage (V) ADJ 1.5 1.8 2.5 2.8 3.0 3.3 5.0 ADJ 1.5 1.8 2.5 2.8 3.0 3.3 5.0 Marking V8605 ADJ V8605 150 V8605 180 V8605 250 V8605 280 V8605 300 V8605 330 V8605 500 V8606 ADJ V8606 150 V8606 180 V8606 250 V8606 280 V8606 300 V8606 330 V8606 500 Package DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) DFN6 (Pb−Free) Shipping† 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 12 NCV8605, NCV8606 PACKAGE DIMENSIONS DFN6 3x3.3 MM, 0.95 PITCH CASE 506AX−01 ISSUE O DATE 20 JAN 2006 NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. DIM A A1 A3 b D D2 E E2 e K L L1 MILLIMETERS MIN NOM MAX 0.80 −−− 0.90 0.00 −−− 0.05 0.20 REF 0.30 −−− 0.40 3.00 BSC 1.90 −−− 2.10 3.30 BSC 1.10 −−− 1.30 0.95 BSC 0.20 −−− −−− 0.40 −−− 0.60 0.00 −−− 0.15 D A B 2X 0.15 C 2X 0.15 C 0.10 C 6X 0.08 C SIDE VIEW D2 6X L 1 3 6X L1 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/ Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative ÇÇÇ ÇÇÇ ÇÇÇ ÇÇÇ 6 PIN 1 REFERENCE E TOP VIEW A (A3) A1 4X C SEATING PLANE SOLDERING FOOTPRINT* 3.60 e K 1 1.35 0.50 6X E2 2.15 4 6X 0.95 PITCH b (NOTE 3) BOTTOM VIEW 0.10 C A B 0.05 C 0.83 6X DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 13 NCV8605/D