NCV8772
LDO Regulator - Ultra
Low Iq, Enable, Reset
350 mA
The NCV8772 is 350 mA LDO regulator with integrated reset
functions dedicated for microprocessor applications. Its robustness allows
NCV8772 to be used in severe automotive environments. Ultra low
quiescent current as low as 24 mA typical makes it suitable for
applications permanently connected to battery requiring ultra low
quiescent current with or without load. This feature is especially critical
when modules remain in active mode when ignition is off. The Enable
function can be used for further decrease of quiescent current in
shutdown mode to 1 mA. The NCV8772 contains protection functions as
current limit, thermal shutdown and reverse output current protection.
http://onsemi.com
MARKING
DIAGRAMS
DPAK−5
DT SUFFIX
CASE 175AA
772yxxG
ALYWW
D2PAK−5
D5S SUFFIX
CASE 936A
NC
V8772yxx
AWLYWWG
D2PAK−7
D7S SUFFIX
CASE 936AB
NC
V8772yxx
AWLYWWG
Features
•
•
•
•
•
•
•
•
•
•
Output Voltage Options: 3.3 V and 5 V
Output Voltage Accuracy: ±1.5% (TJ = 25°C to 125°C)
Output Current up to 350 mA
Ultra Low Quiescent Current: typ 24 mA (max 30 mA)
Very Wide Range of Cout and ESR Values for Stability
Enable Function
− 1 mA Max Quiescent Current when disabled
Microprocessor Compatible Control Functions:
− Reset with Adjustable Power−On Delay
Wide Input Voltage Operation Range: up to 40 V
Protection Features
− Current Limitation
− Thermal Shutdown
− Reverse Output Current Protection
These are Pb−Free Devices
1
1
y
x, xx
A
WL, L
Y
WW
G
Typical Applications
•
•
•
•
Body Control Module
Instruments and Clusters
Occupant Protection and Comfort
Powertrain
VBAT
Cin
0.1 mF
Vout
Vin
Vout
NCV8772
Cout
1 mF
VDD
Microprocessor
DT*
OFF ON
EN
RO
= Timing and Reset Threshold Option
= Voltage Option
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
RESET
GND
* D2PAK−7 ONLY
Figure 1. Typical Application Schematic
© Semiconductor Components Industries, LLC, 2011
September, 2019 − Rev. 3
1
Publication Order Number:
NCV8772/D
NCV8772
Vin
Vout
*
Thermal
Shutdown
RO
Driver
With
Current
Erorr Amplifier
Reset Comparator
Reset Driver
Limit
EN
Enable
Reference
Timing
DT**
Circuit
***
Oscillator
GND
* 5 V OPTION ONLY
** D2PAK−7 ONLY
* ** Pull−Down Resistor (typ 150 kW) active only in Reset State
Figure 2. Simplified Block Diagram
PIN CONNECTIONS
PIN
Tab,
1. Vin
2. RO
3. GND
4. EN
5. Vout
PIN
Tab,
1. Vin
2. RO
3. GND
4. EN
5. Vout
PIN
Tab,
1
1
1
D2PAK−5
DPAK−5
1. Vin
2. RO
3. NC
4. GND
5. EN
6. DT
7. Vout
D2PAK−7
Figure 3. Pin Connections
PIN FUNCTION DESCRIPTION
Pin No.
DPAK−5
D2PAK−5
Pin No.
D2PAK−7
1
1
Vin
Positive Power Supply Input. Connect 0.1 mF capacitor to ground.
2
2
RO
Reset Output. 30 kW internal Pull−up resistor connected to Vout. RO goes Low when Vout
drops by more than 7% (typ) from its nominal value (for NCV8772y devices with y = 1,2,3,...)
or more than 10% (typ) from its nominal value (for NCV8772y devices with y = A, B, C,...).
−
3
NC
Not Connected
3, TAB
4, TAB
GND
4
5
EN
Enable Input. Low level disables the IC.
−
6
DT
Reset Delay Time Select. Short to GND or connected to Vout to select time.
5
7
Vout
Regulated Output Voltage. Connect 1 mF capacitor with ESR < 100 W to ground.
Pin Name
Description
Power Supply Ground.
http://onsemi.com
2
NCV8772
ABSOLUTE MAXIMUM RATINGS
Rating
Input Voltage (Note 1)
Symbol
Min
Max
Unit
Vin
−0.3
−
40
45
V
DC
Transient, t < 100 ms
Input Current
Iin
−5
−
mA
Output Voltage (Note 2)
Vout
−0.3
5.5
V
Output Current
Iout
−3
Current Limited
mA
VEN
−0.3
−
40
45
V
Enable Input Current
IEN
−1
1
mA
DT (Reset Delay Time Select) Voltage
VDT
−0.3
5.5
V
DT (Reset Delay Time Select) Current
IDT
−1
1
mA
Reset Output Voltage
VRO
−0.3
5.5
V
Reset Output Current
IRO
−3
3
mA
Junction Temperature
TJ
−40
150
°C
Storage Temperature
TSTG
−55
150
°C
Enable Input Voltage
DC
Transient, t < 100 ms
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. 5.5 V or (Vin + 0.3 V) (whichever is lower).
ESD CAPABILITY (Note 3)
Rating
Symbol
Min
Max
Unit
ESDHBM
−2
2
kV
ESD Capability, Machine Model
ESDMM
−200
200
V
ESD Capability, Charged Device Model
ESDCDM
−1
1
kV
Max
Unit
ESD Capability, Human Body Model
3. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (JS−001−2010)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
ESD Charge Device Model tested per AEC−Q100−011 (EIA/JESD22−C101)
LEAD SOLDERING TEMPERATURE AND MSL (Note 4)
Rating
Moisture Sensitivity Level
Symbol
DPAK−5
D2PAK−5
D2PAK−7
Min
MSL
Lead Temperature Soldering
Reflow (SMD Styles Only), Pb−Free Versions
TSLD
1
1
3
−
−
265 peak
°C
4. For more information, please refer to our Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
THERMAL CHARACTERISTICS (Note 5)
Rating
Symbol
Value
Thermal Characteristics, DPAK−5
Thermal Resistance, Junction−to−Air (Note 6)
Thermal Reference, Junction−to−Case (Note 6)
RqJA
RYJC
56
8.4
Thermal Characteristics, D2PAK−5
Thermal Resistance, Junction−to−Air (Note 6)
Thermal Reference, Junction−to−Case (Note 6)
RqJA
RYJC
53
8.4
Thermal Characteristics, D2PAK−7
Thermal Resistance, Junction−to−Air (Note 6)
Thermal Reference, Junction−to−Case (Note 6)
RqJA
RYJC
51
8.4
5. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
6. Values based on copper area of 645 mm2 (or 1 in2) of 1 oz copper thickness and FR4 PCB substrate.
http://onsemi.com
3
Unit
°C/W
°C/W
°C/W
NCV8772
RECOMMENDED OPERATING RANGE (Note 7)
Rating
Symbol
Min
Max
Unit
Input Voltage (Note 8)
Vin
4.5
40
V
Junction Temperature
TJ
−40
150
°C
7. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
8. Minimum Vin = 4.5 V or (Vout + VDO), whichever is higher.
ELECTRICAL CHARACTERISTICS Vin = 13.2 V, VEN = 3 V, Cin = 0.1 mF, Cout = 1 mF, for typical values TJ = 25°C, for min/max
values TJ = −40°C to 150°C; unless otherwise noted. (Notes 9 and 10)
Test Conditions
Parameter
Symbol
Min
Typ
Max
Unit
3.2505
4.925
(−1.5 %)
3.3
5.0
3.3495
5.075
(+1.5%)
3.234
3.234
4.9
4.9
(−2 %)
3.3
3.3
5.0
5.0
3.366
3.366
5.1
5.1
(+2%)
3.234
4.9
(−2 %)
3.3
5.0
3.366
5.1
(+2%)
Regline
−20
0
20
mV
Regload
−35
10
35
mV
−
−
250
440
500
875
Cout
ESR
1
0.01
−
−
100
100
mF
W
IDIS
−
−
1
mA
−
−
24
−
29
30
REGULATOR OUTPUT
Output Voltage (Accuracy %)
Output Voltage (Accuracy %)
Output Voltage (Accuracy %)
Line Regulation
TJ = 25 °C to 125 °C
3.3 V Vin = 4.5 V to 16 V, Iout = 0.1 mA to 200 mA
5.0 V Vin = 5.575 V to 16 V, Iout = 0.1 mA to 200 mA
3.3 V Vin = 4.5 V to 40 V, Iout = 0.1 mA to 200 mA
Vin = 4.5 V to 16 V, Iout = 0.1 mA to 350 mA
5.0 V Vin = 5.6 V to 40 V, Iout = 0.1 mA to 200 mA
Vin = 5.975 V to 16 V, Iout = 0.1 mA to 350 mA
TJ = −40°C to 125°C
3.3 V Vin = 4.5 V to 28 V, Iout = 0 mA to 350 mA
5.0 V Vin = 5.975 V to 28 V, Iout = 0 mA to 350 mA
3.3 V Vin = 4.5 V to 28 V, Iout = 5 mA
5.0 V Vin = 6 V to 28 V, Iout = 5 mA
Load Regulation
Dropout Voltage (Note 11)
Iout = 0.1 mA to 350 mA
Vout
Vout
VDO
5.0 V Iout = 200 mA
Iout = 350 mA
Output Capacitor for Stability (Note 12)
Vout
Iout = 0 mA to 350 mA
V
V
V
mV
DISABLE AND QUIESCENT CURRENTS
Disable Current
Quiescent Current (Iq = Iin − Iout)
VEN = 0 V, TJ < 85°C
Iout = 0.1 mA, TJ = 25°C
Iout = 0.1 mA to 350 mA, TJ ≤ 125°C
Iq
mA
CURRENT LIMIT PROTECTION
Current Limit
Vout = 0.96 x Vout_nom
ILIM
400
−
1100
mA
Short Circuit Current Limit
Vout = 0 V
ISC
400
−
1100
mA
Vout_rev
−
2
5.5
V
PSRR
−
60
−
dB
REVERSE OUTPUT CURRENT PROTECTION
Reverse Output Current Protection
VEN = 0 V, Iout = −1 mA
PSRR
Power Supply Ripple Rejection (Note 12) f = 100 Hz, 0.5 Vpp
9. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.
10. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TA [ TJ. Low duty
cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
11. Measured when output voltage falls 100 mV below the regulated voltage at Vin = 13.2 V.
12. Values based on design and/or characterization.
13. See APPLICATION INFORMATION section for Reset Thresholds and Reset Delay Time Options
http://onsemi.com
4
NCV8772
ELECTRICAL CHARACTERISTICS Vin = 13.2 V, VEN = 3 V, Cin = 0.1 mF, Cout = 1 mF, for typical values TJ = 25°C, for min/max
values TJ = −40°C to 150°C; unless otherwise noted. (Notes 9 and 10)
Parameter
Test Conditions
Symbol
Min
Typ
Max
−
2.5
−
−
0.8
−
−
−
3
0.5
5
1
−
2.0
−
−
0.8
−
−
−
1.0
−
3.8
4.2
Unit
ENABLE THRESHOLDS
Vth(EN)
Enable Input Threshold Voltage
Logic Low
Logic High
Enable Input Current
Logic High
Logic Low
VEN = 5 V
VEN = 0 V, TJ < 85°C
IEN_ON
IEN_OFF
V
mA
DT (RESET DELAY TIME SELECT) − D2PAK−7 ONLY
Vth(DT)
DT Threshold Voltage
Logic Low
Logic High
DT Input Current
VDT = 5 V
IDT
V
mA
RESET OUTPUT RO
Input Voltage Reset Threshold
Output Voltage Reset Threshold
(Note 13)
(NCV8772y) where y = 1,2,3,...
3.3 V
Vin decreasing, Vout > VRT
Vin_RT
Vout decreasing
3.3 V
5.0 V
3.3 V
5.0 V
VRT
Vin > 4.5 V
Vin > 5.5 V
Vin > 4.5 V
Vin > 5.5 V
V
%Vout
90
90
87
87
93
93
90
90
96
96
93
93
VRH
−
2.0
−
%Vout
IROmax
1.3
1.75
−
−
−
−
mA
VROL
−
0.15
0.25
V
5.0 V
VROH
4.5
−
−
V
Reset High Level Leakage Current
3.3 V
IROLK
−
−
1.0
Integrated Reset Pull−up Resistor
RRO
15
30
50
(NCV8772y) where y = A,B,C,...
Reset Hysteresis
Maximum Reset Sink Current
3.3 V Vout = 3 V, VRO = 0.25 V
5.0 V Vout = 4.5 V, VRO = 0.25 V
Reset Output Low Voltage
Reset Output High Voltage
Vout > 1 V, IRO < 200 mA
5.0 V
mA
kW
Reset Delay Time (DPAK−5, D2PAK−5) Min Available Time
(Note 13)
Max Available Time
tRD
6.4
102.4
(20%)
8.0
128
9.6
153.6
(20%)
ms
Reset Delay Time (D2PAK−7)
(Note 13)
tRD
3.2
102.4
(20%)
4.0
128
4.8
153.6
(20%)
ms
tRR
16
25
38
ms
Thermal Shutdown Temperature
(Note 12)
TSD
150
175
195
°C
Thermal Shutdown Hysteresis
(Note 12)
TSH
−
25
−
°C
Min Available Time, DT connected to GND
Max Available Time, DT connected to Vout
Reset Reaction Time (see Figure 33)
THERMAL SHUTDOWN
9. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.
10. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TA [ TJ. Low duty
cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
11. Measured when output voltage falls 100 mV below the regulated voltage at Vin = 13.2 V.
12. Values based on design and/or characterization.
13. See APPLICATION INFORMATION section for Reset Thresholds and Reset Delay Time Options
http://onsemi.com
5
NCV8772
TYPICAL CHARACTERISTICS
300
Vin = 13.2 V
Iout = 100 mA
29
28
Iq, QUIESCENT CURRENT (mA)
Iq, QUIESCENT CURRENT (mA)
30
27
26
25
24
23
22
21
20
−40 −20
0
20
40
60
80
Iout = 0 mA
TJ = 25°C
250
200
150
100
50
0
100 120 140 160
0
5
10
TJ, JUNCTION TEMPERATURE (°C)
Figure 4. Quiescent Current vs. Temperature
20
25
30
35
40
Figure 5. Quiescent Current vs. Input Voltage
30
Iq, QUIESCENT CURRENT (mA)
15
Vin, INPUT VOLTAGE (V)
Vin = 13.2 V
29
28
27
TJ = 150°C
26
25
TJ = −40°C
24
TJ = 25°C
23
22
21
20
0
50
100
150
200
250
300
350
IOUT, OUTPUT CURRENT (mA)
Figure 6. Quiescent Current vs. Output Current
3.36
Vin = 13.2 V
Iout = 100 mA
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
5.10
5.05
5.00
4.95
4.90
−40 −20
0
20
40
60
80
100 120 140 160
Vin = 13.2 V
Iout = 100 mA
3.34
3.32
3.30
3.28
3.26
3.24
−40 −20
TJ, JUNCTION TEMPERATURE (°C)
0
20
40
60
80
100 120 140 160
TJ, JUNCTION TEMPERATURE (°C)
Figure 7. Output Voltage vs. Temperature
(5 V Option)
Figure 8. Output Voltage vs. Temperature
(3.3 V Option)
http://onsemi.com
6
NCV8772
TYPICAL CHARACTERISTICS
6
5
Iout = 1 mA
5
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
Iout = 1 mA
4
3
TJ = 25°C
2
TJ = 150°C
1
0
3
2
TJ = 25°C
1
TJ = −40°C
0
1
2
3
4
5
6
7
0
8
0
1
2
3
4
5
6
7
Vin, INPUT VOLTAGE (V)
Figure 9. Output Voltage vs. Input Voltage
(5 V Option)
Figure 10. Output Voltage vs. Input Voltage
(3.3 V Option)
8
800
VDO, DROPOUT VOLTAGE (mV)
700
TJ = 150°C
600
500
TJ = 25°C
400
300
200
TJ = −40°C
100
0
0
TJ = −40°C
TJ = 150°C
Vin, INPUT VOLTAGE (V)
800
VDO, DROPOUT VOLTAGE (mV)
4
50
100
150
200
250
300
700
Iout = 350 mA
600
500
400
Iout = 200 mA
300
200
100
0
−40 −20
350
Iout, OUTPUT CURRENT (mA)
0
20 40 60 80 100 120 140 160
TJ, JUNCTION TEMPERATURE (°C)
Figure 12. Dropout vs. Temperature
(5 V Option)
Figure 11. Dropout vs. Output Current
(5 V Option)
http://onsemi.com
7
NCV8772
TYPICAL CHARACTERISTICS
800
TJ = 25°C
700
ILIM, ISC, CURRENT LIMIT (mA)
ILIM, ISC, CURRENT LIMIT (mA)
800
ISC @ Vout = 0 V
600
ILIM @ Vout = 4.8 V
500
400
300
200
100
0
0
5
10
15
20
25
30
Vin, INPUT VOLTAGE (V)
35
TJ = 25°C
700
ISC @ Vout = 0 V
600
ILIM @ Vout = 3.17 V
500
400
300
200
100
0
40
0
Figure 13. Output Current Limit vs. Input
Voltage (5 V Option)
700
650
ISC @ Vout = 0 V
600
550
ILIM @ Vout = 4.8 V
500
450
400
−40 −20
0
20
40
60
80
15
20
25
30
Vin, INPUT VOLTAGE (V)
35
40
800
ILIM, ISC, CURRENT LIMIT (mA)
750
10
Figure 14. Output Current Limit vs. Input
Voltage (3.3 V Option)
Vin = 13.2 V
Vin = 13.2 V
750
700
650
ISC @ Vout = 0 V
600
550
ILIM @ Vout = 3.17 V
500
450
400
−40 −20
100 120 140 160
0
20
40
60
80
100 120 140 160
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 15. Output Current Limit vs. Temperature
(5 V Option)
Figure 16. Output Current Limit vs. Temperature
(3.3 V Option)
100
ESR, STABILITY REGION (W)
ILIM, ISC, CURRENT LIMIT (mA)
800
5
Vin = 13.2 V
TJ = −40°C to 150°C
Cout = 1 mF − 100 mF
10
1
STABLE REGION
0.1
0.01
0
50
100
150
200
250
300
350
Iout, OUTPUT CURRENT (mA)
Figure 17. Cout ESR Stability Region vs. Output
Current
http://onsemi.com
8
NCV8772
TYPICAL CHARACTERISTICS
TJ = 25°C
Iout = 1 mA
Cout = 10 mF
trise/fall = 1 ms (Vin)
14.2 V
Vin
(1 V/div)
13 V
14.2 V
Vin
(1 V/div)
TJ = 25°C
Iout = 1 mA
Cout = 10 mF
trise/fall = 1 ms (Vin)
12.2 V
13 V
12.2 V
3.42 V
5.11 V
Vout
(50 mV/div)
Vout
(50 mV/div)
5V
3.33 V
4.98 V
3.3 V
TIME (1 ms/div)
TIME (1 ms/div)
Figure 18. Line Transients
(5 V Option)
Figure 19. Line Transients
(3.3 V Option)
TJ = 25°C
Vin = 13.2 V
Cout = 10 mF
trise/fall = 1 ms (Iout)
350 mA
Iout
(200 mA/div)
TJ = 25°C
Vin = 13.2 V
Cout = 10 mF
trise/fall = 1 ms (Iout)
350 mA
Iout
(200 mA/div)
0.1 mA
0.1 mA
5.3 V
3.58 V
3.3 V
5V
Vout
(200 mV/div)
Vout
(200 mV/div)
4.54 V
2.92 V
TIME (20 ms/div)
TIME (20 ms/div)
Figure 20. Load Transients
(5 V Option)
Figure 21. Load Transients
(3.3 V Option)
TJ = 25°C
VEN = Vin
Rout = 5 kW
TJ = 25°C
VEN = Vin
Rout = 3.3 kW
Vin
(5 V/div)
Vin
(5 V/div)
Vout
(5 V/div)
Vout
(5 V/div)
VRO
(5 V/div)
VRO
(5 V/div)
TIME (100 ms/div)
TIME (100 ms/div)
Figure 22. Power Up/Down Response
(5 V Option)
Figure 23. Power Up/Down Response
(3.3 V Option)
http://onsemi.com
9
NCV8772
TYPICAL CHARACTERISTICS
100
80
80
70
PSRR (dB)
60
50
40
60
50
40
30
30
20
20
10
10
0
10
100
1000
10000
TJ = 25°C
Vin = 13.2 V $ 0.5 Vpp
Cout = 1 mF
Iout = 1.0 mA
90
0
10
100000
100
f, FREQUENCY (Hz)
Figure 25. PSRR vs. Frequency
(3.3 V Option)
4000
3500
3000
2500
2000
1500
1000
500
0
10
100
1000
10000
100000
Vin = 13.2 V
VEN = 0 V
4
3
2
1
0
−40 −20
Figure 26. Noise vs. Frequency
50
IEN, ENABLE CURRENT (mA)
IDIS, DISABLE CURRENT (mA)
10
TJ = 150°C
6
4
TJ = 125°C
TJ = 85°C
10
15
20
40
60
80
100 120 140 160
Vin = 13.2 V
VEN = 0 V
5
20
Figure 27. Disable Current vs. Temperature
12
2
0
TJ, JUNCTION TEMPERATURE (°C)
f, FREQUENCY (Hz)
8
100000
5
TJ = 25°C
Vin = 13.2 V
Cout = 1 mF
Iout = 350 mA
0
10000
f, FREQUENCY (Hz)
4500
0
1000
Figure 24. PSRR vs. Frequency
(5 V Option)
IDIS, DISABLE CURRENT (mA)
PSRR (dB)
70
NOISE DENSITY (nV/√Hz)
100
TJ = 25°C
Vin = 13.2 V $ 0.5 Vpp
Cout = 1 mF
Iout = 1.0 mA
90
25
30
35
40
40
TJ = 150°C
30
TJ = 25°C
20
TJ = −40°C
10
0
0
5
10
15
20
25
30
35
VEN, ENABLE VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
Figure 28. Disable Current vs. Input Voltage
Figure 29. Enable Current vs. Enable Voltage
http://onsemi.com
10
40
NCV8772
TYPICAL CHARACTERISTICS
3.18
VRT, RESET THRESHOLD (V)
Vin = 13.2 V
4.75
4.70
4.65
4.60
−40 −20
0
20
40
60
80
100 120 140 160
Vin = 13.2 V
3.16
3.14
3.12
3.10
3.08
3.06
3.04
3.02
−40 −20
0
20
40
60
80
100 120 140 160
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 30. Reset Threshold vs. Temperature
(5 V Option)
Figure 31. Reset Threshold vs. Temperature
(3.3 V Option)
tRD, RESET DELAY TIME (% of tRD_nom)
VRT, RESET THRESHOLD (V)
4.80
120
Vin = 13.2 V
110
100
90
80
−40 −20
0
20
40
60
80
100 120 140 160
TJ, JUNCTION TEMPERATURE (°C)
Figure 32. Reset Delay Time vs. Temperature
Vin
t
Vout
< tRR
VRT + VRH
VRT
VRO
t
tRD
tRR
VROH
VROL
t
Figure 33. Reset Function and Timing Diagram
http://onsemi.com
11
NCV8772
DEFINITIONS
General
Current Limit and Short Circuit Current Limit
All measurements are performed using short pulse low
duty cycle techniques to maintain junction temperature as
close as possible to ambient temperature.
Current Limit is value of output current by which output
voltage drops below 96% of its nominal value. Short Circuit
Current Limit is output current value measured with output
of the regulator shorted to ground.
Output voltage
The output voltage parameter is defined for specific
temperature, input voltage and output current values or
specified over Line, Load and Temperature ranges.
PSRR
Power Supply Rejection Ratio is defined as ratio of output
voltage and input voltage ripple. It is measured in decibels
(dB).
Line Regulation
The change in output voltage for a change in input voltage
measured for specific output current over operating ambient
temperature range.
Line Transient Response
Typical output voltage overshoot and undershoot
response when the input voltage is excited with a given
slope.
Load Regulation
The change in output voltage for a change in output
current measured for specific input voltage over operating
ambient temperature range.
Load Transient Response
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between low−load and high−load conditions.
Dropout Voltage
The input to output differential at which the regulator
output no longer maintains regulation against further
reductions in input voltage. It is measured when the output
drops 100 mV below its nominal value. The junction
temperature, load current, and minimum input supply
requirements affect the dropout level.
Thermal Protection
Quiescent and Disable Currents
Maximum Package Power Dissipation
Quiescent Current (Iq) is the difference between the input
current (measured through the LDO input pin) and the
output load current. If Enable pin is set to LOW the regulator
reduces its internal bias and shuts off the output, this term is
called the disable current (IDIS).
The power dissipation level is maximum allowed power
dissipation for particular package or power dissipation at
which the junction temperature reaches its maximum
operating value, whichever is lower.
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
http://onsemi.com
12
NCV8772
APPLICATIONS INFORMATION
The NCV8772 regulator is self−protected with internal
thermal shutdown and internal current limit. Typical
characteristics are shown in Figure 4 to Figure 33.
RESET DELAY AND RESET THRESHOLD OPTIONS
(DPAK−5 AND D2PAK−5)
Input Decoupling (Cin)
A ceramic or tantalum 0.1 mF capacitor is recommended
and should be connected close to the NCV8772 package.
Higher capacitance and lower ESR will improve the overall
line and load transient response.
If extremely fast input voltage transients are expected then
appropriate input filter must be used in order to decrease
rising and/or falling edges below 50 V/ms for proper
operation. The filter can be composed of several capacitors
in parallel.
Output Decoupling (Cout)
The NCV8772 is a stable component and does not require
a minimum Equivalent Series Resistance (ESR) for the
output capacitor. Stability region of ESR vs Output Current
is shown in Figure 17. The minimum output decoupling
value is 1 mF and can be augmented to fulfill stringent load
transient requirements. The regulator works with ceramic
chip capacitors as well as tantalum devices. Larger values
improve noise rejection and load regulation transient
response.
Reset Delay Time
Reset Threshold
NCV87721DT
NCV87721D5S
8 ms
93%
NCV87722DT
NCV87722D5S
16 ms
93%
NCV87723DT
NCV87723D5S
32 ms
93%
NCV87724DT
NCV87724D5S
64 ms
93%
NCV87725DT
NCV87725D5S
128 ms
93%
NCV8772ADT
NCV8772AD5S
8 ms
90%
NCV8772BDT
NCV8772BD5S
16 ms
90%
NCV8772CDT
NCV8772CD5S
32 ms
90%
NCV8772DDT
NCV8772DD5S
64 ms
90%
NCV8772EDT
NCV8772ED5S
128 ms
90%
Enable Operation
NOTE:
The timing values can be selected from the following list:
8, 16, 32, 64, 128 ms. Contact factory for options not
included in ORDERING INFORMATION table on page 14.
The Enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this datasheet.
Reset Delay Time Select (D2PAK−7 only)
Selection of the NCV8772yD7S devices and the state of
the DT pin determines the available Reset Delay times. The
part is designed for use with DT tied to ground or Vout, but
may be controlled by any logic signal which provides a
threshold between 0.8 V and 2 V. The default condition for
an open DT pin is the slower Reset time (DT = GND
condition). Times are in pairs and are highlighted in the chart
below. Consult factory for availability. The Delay Time
select (DT) pin is logic level controlled and provides Reset
Delay time per the chart. Note the DT pin is sampled only
when RO is low, and changes to the DT pin when RO is high
will not effect the reset delay time.
Reset Operation
A reset signal is provided on the Reset Output (RO) pin to
provide feedback to the microprocessor of an out of
regulation condition. The timing diagram of reset function
is shown in Figure 33. This is in the form of a logic signal on
RO. Output voltage conditions below the RESET threshold
cause RO to go low. The RO integrity is maintained down
to Vout = 1.0 V. For 5 V voltage option, the Reset Output
(RO) circuitry includes internal pull−up (30 kW) connected
to the output (Vout) No external pull−up is necessary.
http://onsemi.com
13
NCV8772
dissipate up to 2.35 W (for D2PAK−5) when the ambient
temperature (TA) is 25°C. See Figure 34 for RqJA versus
PCB area. The power dissipated by the NCV8772 can be
calculated from the following equations:
RESET DELAY AND RESET THRESHOLD OPTIONS
(D2PAK−7)
DT = GND
Reset
Time
DT = Vout
Reset
Time
Reset
Threshold
NCV87721D7S
8 ms
128 ms
93%
NCV87722D7S
8 ms
32 ms
93%
NCV87723D7S
16 ms
64 ms
93%
NCV87724D7S
32 ms
128 ms
93%
NCV87725D7S
4 ms
8 ms
93%
NOTE:
NCV8772AD7S
8 ms
128 ms
90%
100
NCV8772BD7S
8 ms
32 ms
90%
NCV8772CD7S
16 ms
64 ms
90%
NCV8772DD7S
32 ms
128 ms
90%
NCV8772ED7S
4 ms
8 ms
90%
V in(max) +
The timing values can be selected from the following list:
4, 8, 16, 32, 64, 128 ms. Contact factory for options not
included in ORDERING INFORMATION table on page 14.
Thermal Considerations
As power in the NCV8772 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and the ambient temperature
affect the rate of junction temperature rise for the part. When
the NCV8772 has good thermal conductivity through the
PCB, the junction temperature will be relatively low with
high power applications. The maximum dissipation the
NCV8772 can handle is given by:
P D(max) +
ƪTJ(max) * TAƫ
(eq. 2)
or
RqJA, THERMAL RESISTANCE (°C/W)
NOTE:
P D + V inǒI q@I outǓ ) I outǒV in * V outǓ
P D(max) ) ǒV out
I outǓ
(eq. 3)
I out ) I q
Items containing Iq can be neglected if Iout >> Iq.
90
80
70
PCB 1 oz Cu
60
50
40
0
PCB 2 oz Cu
100
200
300
400
500
600
COPPER HEAT SPREADER (mm2)
700
Figure 34. Thermal Resistance vs. PCB Copper Area
(D2PAK−5)
Hints
Vin and GND printed circuit board traces should be as
wide as possible. When the impedance of these traces is
high, there is a chance to pick up noise or cause the regulator
to malfunction. Place external components, especially the
output capacitor, as close as possible to the NCV8772 and
make traces as short as possible.
(eq. 1)
R qJA
Since TJ is not recommended to exceed 150°C, then the
NCV8772 soldered on 645 mm2, 1 oz copper area, FR4 can
ORDERING INFORMATION
Output Voltage
Reset Delay Time
(DT = GND/Vout
for D2PAK−7)
Reset Threshold
Marking
Package
Shipping†
NCV87722DT50RKG
5.0 V
16 ms
93%
772250G
DPAK−5
(Pb−Free)
2500 /
Tape & Reel
NCV87721D5S50R4G
5.0 V
8 ms
93%
NC
V8772150
D2PAK−5
(Pb−Free)
800 /
Tape & Reel
NCV87725D7S50R4G
5.0 V
4/8 ms
93%
NC
V8772550
D2PAK−7
(Pb−Free)
750 /
Tape & Reel
NCV87722DT33RKG
3.3 V
16 ms
93%
772233G
DPAK−5
(Pb−Free)
2500 /
Tape & Reel
NCV87722D5S33R4G
3.3 V
16 ms
93%
NC
V8772233
D2PAK−5
(Pb−Free)
800 /
Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
14
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
DPAK−5, CENTER LEAD CROP
CASE 175AA
ISSUE B
DATE 15 MAY 2014
SCALE 1:1
−T−
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
E
R
R1
Z
A
S
12 3 4 5
U
K
F
J
L
H
D
G
5 PL
0.13 (0.005)
M
T
2.2
0.086
0.34 5.36
0.013 0.217
5.8
0.228
10.6
0.417
0.8
0.031
SCALE 4:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DOCUMENT NUMBER:
DESCRIPTION:
98AON12855D
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.020 0.028
0.018 0.023
0.024 0.032
0.180 BSC
0.034 0.040
0.018 0.023
0.102 0.114
0.045 BSC
0.170 0.190
0.185 0.210
0.025 0.040
0.020
−−−
0.035 0.050
0.155 0.170
MILLIMETERS
MIN
MAX
5.97
6.22
6.35
6.73
2.19
2.38
0.51
0.71
0.46
0.58
0.61
0.81
4.56 BSC
0.87
1.01
0.46
0.58
2.60
2.89
1.14 BSC
4.32
4.83
4.70
5.33
0.63
1.01
0.51
−−−
0.89
1.27
3.93
4.32
GENERIC
MARKING DIAGRAMS*
RECOMMENDED
SOLDERING FOOTPRINT*
6.4
0.252
DIM
A
B
C
D
E
F
G
H
J
K
L
R
R1
S
U
V
Z
XXXXXXG
ALYWW
AYWW
XXX
XXXXXG
IC
Discrete
XXXXXX
A
L
Y
WW
G
= Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DPAK−5 CENTER LEAD CROP
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
D2PAK 5−LEAD
CASE 936A−02
ISSUE E
DATE 28 JUL 2021
SCALE 1:1
GENERIC
MARKING DIAGRAM*
xx
xxxxxxxxx
AWLYWWG
xxxxxx
A
WL
Y
WW
G
= Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
DOCUMENT NUMBER:
DESCRIPTION:
98ASH01006A
D2PAK 5−LEAD
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
D2PAK−7 (SHORT LEAD)
CASE 936AB−01
ISSUE B
DATE 08 SEP 2009
A
1
SCALE 1:1
E
L1
B
A
0.10
A
E/2
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH AND GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.005 MAXIMUM PER SIDE. THESE DIMENSIONS
TO BE MEASURED AT DATUM H.
4. THERMAL PAD CONTOUR OPTIONAL WITHIN
DIMENSIONS E, L1, D1, AND E1. DIMENSIONS
D1 AND E1 ESTABLISH A MINIMUM MOUNTING
SURFACE FOR THE THERMAL PAD.
SEATING
PLANE
M
B A
M
E1
c2
D1
D
7X
H
DETAIL C
e
b
0.13
M
B A
VIEW A−A
c
A
M
B
H
SEATING
PLANE
A1
RECOMMENDED
SOLDERING FOOTPRINT*
L
0.424
INCHES
MIN
MAX
0.170
0.180
0.000
0.010
0.026
0.036
0.017
0.026
0.045
0.055
0.325
0.368
0.270
−−−
0.380
0.420
0.245
−−−
0.050 BSC
0.539
0.579
0.058
0.078
−−−
0.066
0.010 BSC
0°
8°
MILLIMETERS
MIN
MAX
4.32
4.57
0.00
0.25
0.66
0.91
0.43
0.66
1.14
1.40
8.25
9.53
6.86
−−−
9.65
10.67
6.22
−−−
1.27 BSC
13.69
14.71
1.47
1.98
−−−
1.68
0.25 BSC
0°
8°
GENERIC
MARKING DIAGRAM*
M
L3
DIM
A
A1
b
c
c2
D
D1
E
E1
e
H
L
L1
L3
M
GAUGE
PLANE
XX
XXXXXXXXX
AWLYWWG
DETAIL C
0.310
0.584
1
XXXXX
A
WL
Y
WW
G
0.136
7X
0.050
PITCH
0.040
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DOCUMENT NUMBER:
DESCRIPTION:
98AON14119D
D2PAK−7 (SHORT LEAD)
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative