Intelligent Power Module
(IPM), 650 V, 30 A
NFAM3065L4B
General Description
The NFAM3065L4B is a fully-integrated inverter power module
consisting of an independent High side gate driver, LVIC, six IGBT’s
and a temperature sensor (VTS), suitable for driving permanent
magnet synchronous (PMSM) motors, brushless DC (BLDC) motors
and AC asynchronous motors. The IGBT’s are configured in a
three-phase bridge with separate emitter connections for the lower
legs for maximum flexibility in the choice of control algorithm.
The power stage has under voltage lockout protection (UVP).
Internal boost diodes are provided for high side gate boost drive.
www.onsemi.com
Features
•
•
•
•
•
•
•
•
Three-phase 650 V, 30 A IGBT Module with Independent Drivers
Active Logic Interface
Built-in Undervoltage Protection (UVP)
Integrated Bootstrap Diodes and Resistors
Separate Low-side IGBT Emitter Connections for Individual
Current Sensing of Each Phase
Temperature Sensor (VTS)
UL1557 Certified (File No.339285)
This Device is Pb−Free and RoHS Compliant
DIP39 54.5 x 31.0
CASE MODGX
MARKING DIAGRAM
Typical Applications
•
•
•
•
NFAM3065L4B
ZZZATYWW
Industrial Drives
Industrial Pumps
Industrial Fans
Industrial Automation
Device marking is on package top side
P
VS(U)
VB(U)
VDD(UH)
HIN(U)
VS(V)
VB(V)
VDD(VH)
HIN(V)
VS(W)
VB(W)
VDD(WH)
HIN(W)
VTS
LIN(U)
LIN(V)
LIN(W)
VFO
CFOD
CIN
VSS
VDD(L)
High Side
HVI C1
HS1
High Side
HVI C2
HS2
High Side
HVI C3
HS3
HS1
U
V
HS2
W
NFAM3065L4B
ZZZ
A
T
Y
WW
= Specific Device Code
= Assembly Lot Code
= Assembly Location
= Test Location
= Year
= Work Week
HS3
ORDERING INFORMATION
Device
LS1
Low Side
LVIC
with
Protection
LS2
LS3
NFAM3065L4B
LS1
LS2
Package
Shipping
DIP39
54.5 x 31.0
(Pb-Free)
90 / Box
LS3
NU
NV
NW
Figure 1. Application Schematic
© Semiconductor Components Industries, LLC, 2019
April, 2020 − Rev. 1
1
Publication Order Number:
NFAM3065L4B/D
NFAM3065L4B
APPLICATION SCHEMATIC
VB(U) (3)
N.C (38)
VS(U) (1)
P (37)
CS
HIN(U) (6)
VDD(UH) (4)
HIN
VDD
+
C1
VB
HOUT
HVIC1
VS
VSS
U (36)
VB(V) (9)
VS(V) (7)
HIN(V) (12)
VDD(VH) (10)
VB
HOUT
HIN
HVIC2
VDD
V (35)
VSS
VS
HIN
VB
HOUT
HVIC3
VB(W) (15)
VS(W) (13)
MCU
HIN(W) (18)
VDD(WH) (16)
VDD
VSS
VTS (20)
LIN(U) (21)
LIN(V) (22)
LIN(W) (23)
VS
W (34)
VTS
OUT(U)
LIN(U)
NU (33)
LIN(V)
LIN(W)
5 V line
VFO (24)
CFOD (25)
CIN (26)
15 V line
VDD(L) (28)
VSS (27)
VFO
LVIC
OUT(V)
CFOD
NV (32)
CIN
VDD
OUT(W)
VSS
NW (31)
Signal for over current trip
Phase current
Figure 2. Application Schematic − Adjustable Option
www.onsemi.com
2
Motor
NFAM3065L4B
BLOCK DIAGRAM
N.C (38)
VS(U) (1)
P (37)
VB(U) (3)
VB
VDD(UH) (4)
HIN(U) (6)
HOUT
VDD
HIN
HVIC1
VSS
VS
VDD
HOUT
U (36)
VS(V) (7)
VB(V)(9)
VB
VDD(VH) (10)
HIN(V) (12)
HIN
HVIC2
VSS
VS
VDD
HOUT
V (35)
VS(W) (13)
VB(W) (15)
VB
VDD(WH) (16)
HIN(W) (18)
HIN
HVIC3
VTS (20)
OUT(U)
VTS
LIN(U) (21)
LIN(U)
LIN(V) (22)
LIN(V)
LIN(W) (23)
LIN(W)
NU (33)
LVIC
VFO (24)
CFOD (25)
VFO
W (34)
VS
VSS
OUT(V)
CFOD
NV (32)
CIN (26)
CIN
VSS (27)
VSS
VDD(L) (28)
VDD
OUT(W)
NW (31)
Figure 3. Equivalent Block Diagram
www.onsemi.com
3
NFAM3065L4B
PIN FUNCTION DESCRIPTION
Pin
Name
1
VS(U)
(2)
−
3
VB(U)
Description
High−Side Bias Voltage GND for U phase IGBT Driving
Dummy
High−Side Bias Voltage for U phase IGBT Driving
4
VDD(UH)
(5)
−
High−Side Bias Voltage for U phase IC
6
HIN(U)
Signal Input for High−Side U Phase
7
VS(V)
High−Side Bias Voltage GND for V phase IGBT Driving
(8)
−
9
VB(V)
Dummy
Dummy
High−Side Bias Voltage for V phase IGBT Driving
10
VDD(VH)
(11)
−
High−Side Bias Voltage for V phase IC
12
HIN(V)
Signal Input for High−Side V Phase
13
VS(W)
High−Side Bias Voltage GND for W phase IGBT Driving
(14)
−
15
VB(W)
Dummy
Dummy
High−Side Bias Voltage for W phase IGBT Driving
16
VDD(WH)
(17)
−
High−Side Bias Voltage for W phase IC
18
HIN(W)
(19)
−
20
VTS
21
LIN(U)
Signal Input for Low−Side U Phase
22
LIN(V)
Signal Input for Low−Side V Phase
23
LIN(W)
Signal Input for Low−Side W Phase
24
VFO
25
CFOD
26
CIN
Input for Current Protection
27
VSS
Low−Side Common Supply Ground
Dummy
Signal Input for High−Side W Phase
Dummy
Voltage Output for LVIC Temperature Sensing Unit
Fault Output
Capacitor for Fault Output Duration Selection
28
VDD(L)
(29)
−
Low−Side Bias Voltage for IC and IGBTs Driving
Dummy
(30)
−
Dummy
31
NW
Negative DC−Link Input for U Phase
32
NV
Negative DC−Link Input for V Phase
33
NU
Negative DC−Link Input for W Phase
34
W
Output for U Phase
35
V
Output for V Phase
36
U
Output for W Phase
37
P
Positive DC−Link Input
38
N.C
(39)
−
No Connection
Dummy
1. Pins of () are the dummy for internal connection. These pins should be no connection.
www.onsemi.com
4
NFAM3065L4B
ABSOLUTE MAXIMUM RATINGS (TC = 25°C) (Note 2)
Symbol
Value
Unit
Supply Voltage
P−NU, NV, NW
450
V
VPN(surge)
Supply Voltage (Surge)
P−NU, NV, NW (Note 3)
550
V
VPN(PROT)
Self Protection Supply Voltage Limit
(Short-Circuit Protection Capability)
VDD = VBS = 13.5 V ~ 16.5 V,
Tj = 150°C, VCES < 650 V,
Non-Repetitive, < 2 ms
400
V
Collector−emitter voltage
650
V
Maximum Repetitive Revers Voltage
650
V
±Ic
Each IGBT Collector Current
±30
A
±Icp
Each IGBT Collector Current (Peak)
Under 1 ms Pulse Width
±60
A
VDD
Control Supply Voltage
VDD(UH,VH,WH), VDD(L)−VSS
−0.3 to 20
V
VBS
High−Side Control Bias Voltage
VB(U)−VS(U), VB(V)−VS(V),
VB(W)−VS(W)
−0.3 to 20
V
VIN
Input Signal Voltage
HIN(U), HIN(V), HIN(W), LIN(U), LIN(V),
LIN(W)–VSS
−0.3 to VDD
V
VFO
Fault Output Supply Voltage
VFO–VSS
−0.3 to VDD
V
IFO
Fault Output Current
Sink Current at VFO pin
2
mA
Current Sensing Input Voltage
CIN–VSS
−0.3 to VDD
V
Pc
Corrector Dissipation
Per One Chip
113
W
Tj
Operating Junction Temperature
−40 to +150
°C
Storage temperature
−40 to +125
°C
Module Case Operation Temperature
−40 to +125
°C
2500
V rms
VPN
Vces
VRRM
VCIN
Tstg
Tc
Viso
Rating
Isolation voltage
Conditions
60 Hz, Sinusoidal, AC 1 minute, Connection
Pins to Heat Sink Plate
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
2. Refer to ELECTRICAL CHARACTERISTICS, RECOMMENDED OPERATING RANGES and/or APPLICATION INFORMATION for Safe
Operating parameters.
3. This surge voltage developed by the switching operation due to the wiring inductance between P and NU, NV, NW terminal.
THERMAL CHARACTERISTICS
Symbol
Rth(j-c)Q
Rth(j-c)F
Rating
Junction-to-Case Thermal
Resistance
Conditions
Min
Typ
Max
Unit
Inverter IGBT Part (per 1/6 module)
−
−
1.1
°C/W
Inverter FWD Part (per 1/6 module)
−
−
2.2
°C/W
4. Refer to ELECTRICAL CHARACTERISTICS, RECOMMENDED OPERATING RANGES and/or APPLICATION INFORMATION for Safe
Operating parameters.
www.onsemi.com
5
NFAM3065L4B
RECOMMENDED OPERATING CONDITIONS
Symbol
Rating
Conditions
Min
Typ
Max
Unit
−
300
400
V
VPN
Supply Voltage
P−NU, NV, NW
VDD
Gate Driver Supply
Voltages
VDD(UH,VH,WH), VDD(L)−VSS
13.5
15
16.5
V
VB(U)−VS(U), VB(V)−VS(V),
VB(W)−VS(W)
13.0
15
18.5
V
Supply Voltage Variation
−1
−
1
V/ms
PWM Frequency
1
−
20
kHz
VBS
dVDD / dt,
dVBS / dt
fPWM
DT
Io
PWIN (on)
1.5
−
−
ms
fPWM = 5 kHz
−
−
25.7
A rms
fPWM = 15 kHz
−
−
18.8
200 V ≤ VPN ≤ 400 V
13.5 V ≤ VDD ≤ 16.5 V
13.0 V ≤ VBS ≤ 18.5 V
−20°C ≤ Tc ≤ 100°C
1.0
−
−
1.5
−
−
M3 type screw
0.6
0.7
0.9
Dead Time
Turn-off to Turn-on (external)
Allowable r.m.s. Current
VPN = 300 V,
VDD = 15 V,
P.F. = 0.8
Tc ≤ 125°C,
Tj ≤ 150°C
(Note 5)
Allowable Input Pulse
Width
PWIN (off)
Package Mounting Torque
ms
Nm
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
5. Allowable r.m.s current depends on the actual conditions.
6. Flatness tolerance of the heatsink should be within −50 mm to +100 mm.
ELECTRICAL CHARACTERISTICS (Tc = 25°C, VDD = 15 V, VBS = 15 V, unless otherwise specified.) (Note 7)
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
INVERTER SECTION
Ices
VCE(sat)
VF
ton
Collector−Emitter Leakage
Current
Vce = Vces , Tj = 25°C
−
−
1
mA
Vce = Vces, Tj = 150°C
−
−
10
mA
Collector−Emitter Saturation
Voltage
VDD = VBS = 15 V, IN = 5 V
Ic = 30 A, Tj = 25°C
−
1.60
2.30
V
VDD = VBS = 15 V, IN = 5 V
Ic = 30 A, Tj = 150°C
−
1.80
−
V
IN = 0 V, If = 30 A, Tj = 25°C
−
2.00
2.40
V
IN = 0 V, If = 30 A, Tj = 150°C
−
2.00
−
V
0.80
1.25
1.85
ms
FWDi Forward Voltage
High side
Switching
Times
VPN = 300 V, VDD(H) = VDD(L) = 15 V
Ic = 30 A, Tj = 25°C, IN = 0 ⇔ 5 V
Inductive Load
−
0.25
0.65
ms
toff
−
1.60
2.20
ms
tc (off)
−
0.25
0.75
ms
trr
−
0.15
−
ms
0.80
1.40
2.00
ms
−
0.25
0.55
ms
tc(on)
ton
tc(on)
Low side
Switching
Times
VPN = 300 V, VDD(H) = VDD(L) = 15 V
Ic = 30 A, Tj = 25°C, IN = 0 ⇔ 5 V
Inductive Load
toff
−
1.60
2.20
ms
tc(off)
−
0.25
0.75
ms
trr
−
0.10
−
ms
www.onsemi.com
6
NFAM3065L4B
ELECTRICAL CHARACTERISTICS (Tc = 25°C, VDD = 15 V, VBS = 15 V, unless otherwise specified.) (Note 7) (continued)
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
DRIVER SECTION
IQDDH
Quiescent VDD Supply Current
IQDDL
IPDDH
Operating VDD Supply Current
IPDDL
VDD(UH,VH,WH) = 15 V,
HIN(U,V,W) = 0 V
VDD(UH)−VSS
VDD(VH)−VSS
VDD(WH)−VSS
−
−
0.30
mA
VDD(L) = 15 V,
LIN(U,V,W) = 0 V
VDD(L)–VSS
−
−
3.50
mA
VDD(UH,VH,WH) = 15 V,
VDD(UH)−VSS
fPWM = 20 kHz, Duty = 50%, VDD(VH)−VSS
Applied to one PWM Signal VDD(WH)−VSS
Input for High−Side
−
−
0.40
mA
VDD(L) = 15 V,
VDD(L)−VSS
fPWM = 20 kHz, Duty = 50%,
Applied to one PWM Signal
Input for Low−Side
−
−
6.00
mA
IQBS
Quiescent VBS Supply Current
VBS = 15 V,
HIN(U,V,W) = 0 V
VB(U)−VS(U)
VB(V)−VS(V)
VB(W)−VS(W)
−
−
0.30
mA
IPBS
Operating VBS Supply Current
VDD = VBS = 15 V,
VB(U)−VS(U)
fPWM = 20 kHz, Duty = 50%, VB(V)−VS(V)
Applied to one PWM Signal VB(W)−VS(W)
Input for High−Side
−
−
5.00
mA
VIN(ON)
ON Threshold voltage
HIN(U,V,W)−VSS, LIN(U,V,W)−VSS
−
−
2.6
V
VIN(OFF)
OFF Threshold voltage
0.8
−
−
V
VCIN(ref)
Short Circuit Trip Level
VDD = 15 V, CIN−VSS
0.46
0.48
0.50
V
Supply Circuit
Under-Voltage Protection
Detection Level
10.3
−
12.5
V
Reset Level
10.8
−
13.0
V
UVBSD
Detection Level
10.0
−
12.0
V
UVBSR
Reset Level
10.5
−
12.5
V
Voltage Output for LVIC
Temperature Sensing Unit
VTS−VSS = 10 nF, Temp. = 25°C
0.905
1.030
1.155
V
Fault Output Voltage
VDD = 0 V, CIN = 0 V,
VFO Circuit: 10 kW to 5 V Pull-up
4.9
−
−
V
VDD = 0 V, CIN = 1 V,
VFO Circuit: 10 kW to 5 V Pull-up
−
−
0.95
V
CFOD = 22 nF
1.6
2.4
−
ms
If = 0.1 A
3.4
4.6
5.8
V
30
38
46
W
UVDDD
UVDDR
VTS
VFOH
VFOL
tFOD
Fault-Output Pulse Width
BOOTSTRAP SECTION
VF
RBOOT
Bootstrap Diode Forward
Voltage
Built-in Limiting Resistance
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
7. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25_C. Low
duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
8. The fault-out pulse width tFOD depends on the capacitance value of CFOD according to the following approximate equation:
tFOD = 0.1 × 106 × CFOD (s).
9. Values based on design and/or characterization.
www.onsemi.com
7
NFAM3065L4B
Temperature of LVIC versus VTS Characteristics
4.0
VTS Output Voltage (V)
3.5
3.0
2.5
2.0
1.5
1.0
40
45
50
55
60
65
70
75
80
85
90
95
100 105 110 115 120 125 130
LVIC Temperature (°C)
Figure 4. Temperature of LVIC versus VTS Characteristics
www.onsemi.com
8
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
DIP39, 54.5x31.0 EP−2
CASE MODGX
ISSUE O
DATE 02 APR 2019
GENERIC
MARKING DIAGRAM*
XXXXXXXXXXXXXXXXX
ZZZATYWW
XXXXX = Specific Device Code
ZZZ
= Assembly Lot Code
AT
= Assembly & Test Location
Y
= Year
WW = Work Week
*This information is generic. Please refer to device data
sheet for actual part marking. Pb−Free indicator, “G” or
microdot “ G”, may or may not be present. Some products
may not follow the Generic Marking.
DOCUMENT NUMBER:
DESCRIPTION:
98AON05290H
DIP39, 54.5x31.0 EP−2
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative