NLAS2066USG

NLAS2066 Ultra-Small Dual Single Pole, Single Throw Analog Switch with Over Voltage Tolerance www.onsemi.com The NLAS2066 is a Dual SPST (Single Pole, Single Throw) Analog Switch high performance version of the popular NLAS323. Packaged in the ultra−small US8 package. It is designed as a general analog/digital switch and can also be used to isolate USB ports. Features • • • • • • • • • • • Same Pinout as the Popular NLAS323 Excellent Performance – Maximum RDSON 15  at 3.0 V Matching Between the Switches "1.5  at 3.0 V 1.65 V to 5.5 V Operating Range Lower Threshold Voltages for LVTTL/CMOS Levels Ultra−Low Charge Injection v 4.8 pC at 3.0 V Low Standby Power – ICC = 1.0 nA (max) @ TA = 25°C CMOS Level Compatibility OVT* (Pins 1, 3, 5, and 7) These Pins may be Subjected to 0 to +7.0 V, Regardless of Operating Voltage Allows a Short from USB Line without Damage to the Device These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant Typical Applications • • • • USB Isolation Cell Phones PDAs MP3s Digital Still Cameras 8 US8 US SUFFIX CASE 493 8 1 AH MG G 1 AH = Specific Device Code M = Date Code G = Pb−Free Package (Note: Microdot may be in either location) NO1 1 8 VCC COM1 2 7 IN1 IN2 3 6 COM2 GND 4 5 NO2 PIN ASSIGNMENT Important Information • ESD Protection: • MARKING DIAGRAM Human Body Model; > 1500 V Machine Model; > 200 V Latch−Up Maximum Rating: 200 mA Pin Function OVT 1 NO1 Yes 2 COM1 − 3 IN2 Yes 4 GND − 5 NO2 Yes 6 COM2 − 7 IN1 Yes 8 VCC − FUNCTION TABLE *Over Voltage Tolerance (OVT) enables pins to function outside (higher) of their operating voltages, with no damage to the devices or to signal integrity. © Semiconductor Components Industries, LLC, 2015 July, 2015 − Rev. 9 1 On/Off Enable Input State of Analog Switch L H Off On ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. Publication Order Number: NLAS2066/D NLAS2066 MAXIMUM RATINGS Symbol Rating Value Unit *0.5 to )7.0 V *0.5 to )7.0 −0.5 to VCC V *0.5 to )7.0 V VI < GND *50 mA VO < GND *50 mA VCC DC Supply Voltage VI DC Input Voltage VO DC Output Voltage IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Sink Current $50 mA ICC DC Supply Current per Supply Pin $100 mA IGND DC Ground Current per Ground Pin $100 mA TSTG Storage Temperature Range *65 to )150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature under Bias )150 °C JA Thermal Resistance (Note 1) 250 °C/W PD Power Dissipation in Still Air at 85°C 250 mW MSL Moisture Sensitivity Level 1 − FR Flammability Rating UL 94 V−0 @ 0.125 in − VESD ESD Withstand Voltage > 1500 > 200 N/A V Pins 1, 3, 5, 7 Pins 2, 6 Oxygen Index: 28 to 34 Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2−ounce copper trace with no air flow 2. Tested to EIA/JESD22−A114−A 3. Tested to EIA/JESD22−A115−A 4. Tested to JESD22−C101−A RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit 5.5 V VCC Positive DC Supply Voltage 1.65 VIN Digital Input Voltage (INx) GND 5.5 V VIO Static or Dynamic Voltage Across an Off Switch GND VCC V VIS Analog Input Voltage GND GND 5.5 VCC V TA Operating Temperature Range, All Package Types −55 +125 °C tr, tf Input Rise or Fall Time (Enable Input) 0 0 100 20 ns/V NO COM VCC = 3.3 V + 0.3 V VCC = 5.0 V + 0.5 V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. www.onsemi.com 2 NLAS2066 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80°C 117.8 TJ = 90°C 1,032,200 TJ = 100°C 80 TJ = 110°C Time, Years TJ = 120°C Time, Hours FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 130°C Junction Temperature 5C NORMALIZED FAILURE RATE DEVICE JUNCTION TEMPERATURE VS. TIME TO 0.1% BOND FAILURES 1 1 10 100 1000 TIME, YEARS Figure 1. Failure Rate vs. Time Junction Temperature DC CHARACTERISTICS − Digital Section (Voltages Referenced to GND) Guaranteed Max Limit Symbol Parameter Condition VCC 255C −40 to 855C −55 to