NLU3G16FMUTCG

NLU3G16 Triple Non-Inverting Buffer The NLU3G16 MiniGatet is an advanced high−speed CMOS triple non−inverting buffer in ultra−small footprint. The NLU3G16 input and output structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. www.onsemi.com Features • • • • • • • High Speed: tPD = 3.5 ns (Typ) @ VCC = 5.0 V Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C Power Down Protection Provided on inputs Balanced Propagation Delays Overvoltage Tolerant (OVT) Input and Output Pins Ultra−Small Packages These are Pb−Free Devices 1 IN A1 OUT Y3 8 MARKING DIAGRAMS UDFN8 1.8 x 1.2 CASE 517AJ UYM G 1 ULLGA8 1.95 x 1.0 CASE 613AC LRM G 1 UDFN8 1.45x1, 0.35P CASE 517BZ 8 1 VCC 2 7 OUT Y1 3 6 IN A3 UDFN8 1.6x1, 0.4P CASE 517BY IN A2 1 4 GND 5 DM 1 AD M 1 OUT Y2 Figure 1. Pinout (Top View) UDFN8 1.95x1, 0.5P CASE 517CA 1 IN A1 1 OUT Y2 IN A2 1 OUT Y2 IN A3 1 OUT Y3 AA M 1 UY, R or LR = Specific Device Code M = Date Code G = Pb−Free Package FUNCTION TABLE Figure 2. Logic Symbol A Y L H L H PIN ASSIGNMENT 1 IN A1 2 OUT Y3 3 IN A2 4 GND 5 OUT Y2 6 IN A3 7 OUT Y1 8 VCC © Semiconductor Components Industries, LLC, 2016 July, 2016 − Rev. 5 ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. 1 Publication Order Number: NLU3G16/D NLU3G16 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage −0.5 to +7.0 V VIN DC Input Voltage −0.5 to +7.0 V DC Output Voltage −0.5 to +7.0 V VIN < GND −20 mA VOUT < GND ±20 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current ±12.5 mA ICC DC Supply Current Per Supply Pin ±25 mA IGND DC Ground Current per Ground Pin ±25 mA TSTG Storage Temperature Range −65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C MSL FR ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 Latchup Performance Above VCC and Below GND at 125°C (Note 2) UL 94 V−0 @ 0.125 in ±500 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V −55 +125 °C 0 0 100 20 ns/V VOUT TA Operating Free−Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V www.onsemi.com 2 NLU3G16 DC ELECTRICAL CHARACTERISTICS Symbol VIH VIL VOH VOL Parameter VCC (V) Conditions Low−Level Input Voltage Low−Level Input Voltage High−Level Output Voltage Low−Level Output Voltage TA = 25 5C Min Typ TA = +855C Max Min 1.65 0.75 x VCC 0.75 x VCC 2.3 to 5.5 0.70 x VCC 0.70 x VCC Max TA = −555C to +1255C Min Max V 1.65 0.25 x VCC 0.25 x VCC 0.25 x VCC 2.3 to 5.5 0.30 x VCC 0.30 x VCC 0.30 x VCC VIN = VIH or VIL IOH = −50 mA 2.0 3.0 4.5 1.9 2.9 4.4 VIN = VIH or VIL IOH = −4 mA IOH = −8 mA 3.0 4.5 2.58 3.94 VIN = VIH or VIL IOL = 50 mA 2.0 3.0 4.5 VIN = VIH or VIL IOL = 4 mA IOL = 8 mA 2.0 3.0 4.5 Unit 1.9 2.9 4.4 1.9 2.9 4.4 2.48 3.80 2.34 3.66 V V V 0 0 0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V IIN Input Leakage Current 0 v VIN v 5.5 V 0 to 5.5 ±0.1 ±1.0 ±1.0 mA ICC Quiescent Supply Current VIN = VCC or GND 5.5 1.0 10 40 mA AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) Symbol Parameter VCC (V) Test Condition tPLH, tPHL Propagation Delay, Input A to Output Y 3.0 to 3.6 4.5 to 5.5 CIN Input Capacitance CPD Power Dissipation Capacitance (Note 3) TA = 25 5C Min TA = +855C Typ Max CL = 15 pF 4.5 7.1 CL = 50 pF 6.4 CL = 15 pF CL = 50 pF 5.0 Max Unit 8.5 10 ns 10.6 12 14.5 3.5 5.5 6.5 8.0 4.5 7.5 8.5 10 4.0 10 10 10 8.0 Min Max TA = −555C to +1255C Min pF pF 3. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD • VCC • fin + ICC. CPD is used to determine the no−load dynamic power consumption: PD = CPD • VCC2 • fin + ICC • VCC. www.onsemi.com 3 NLU3G16 SWITCHING WAVEFORMS TEST POINT VCC 50% OUTPUT A GND DEVICE UNDER TEST tPHL tPLH 50% VCC CL * Y *Includes all probe and jig capacitance Figure 3. Switching Waveforms Figure 4. Test Circuit ORDERING INFORMATION Package Shipping† UDFN8 (Pb−Free) 3000 / Tape & Reel NLU3G16AMX1TCG ULLGA8, 1.95 x 1.0, 0.5P (Pb−Free) 3000 / Tape & Reel NLU3G16DMUTCG UDFN8, 1.95 x 1 (Pb−Free) 3000 / Tape & Reel NLU3G16EMUTCG UDFN8, 1.6 x 1 (Pb−Free) 3000 / Tape & Reel NLU3G16FMUTCG UDFN8, 1.45 x 1 (Pb−Free) 3000 / Tape & Reel Device NLU3G16MUTAG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 4 NLU3G16 PACKAGE DIMENSIONS UDFN8 1.8x1.2, 0.4P CASE 517AJ ISSUE O PIN ONE REFERENCE NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM TERMINAL TIP. 4. MOLD FLASH ALLOWED ON TERMINALS ALONG EDGE OF PACKAGE. FLASH MAY NOT EXCEED 0.03 ONTO BOTTOM SURFACE OF TERMINALS. 5. DETAIL A SHOWS OPTIONAL CONSTRUCTION FOR TERMINALS. A B D 0.10 C ÉÉÉ ÉÉÉ L1 E DETAIL A NOTE 5 0.10 C TOP VIEW (A3) 0.05 C DIM A A1 A3 b b2 D E e L L1 L2 A 0.05 C SIDE VIEW A1 e/2 e (b2) C DETAIL A 8X 1 SEATING PLANE L 4 MOUNTING FOOTPRINT SOLDERMASK DEFINED (L2) 8 5 BOTTOM VIEW MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.127 REF 0.15 0.25 0.30 REF 1.80 BSC 1.20 BSC 0.40 BSC 0.45 0.55 0.00 0.03 0.40 REF 8X b 8X 0.10 M C A B 0.05 M C 0.66 7X 0.22 NOTE 3 1.50 1 0.32 0.40 PITCH DIMENSIONS: MILLIMETERS www.onsemi.com 5 NLU3G16 PACKAGE DIMENSIONS UDFN8, 1.6x1, 0.4P CASE 517BY ISSUE O PIN ONE REFERENCE 0.10 C 2X 2X ÉÉÉ ÉÉÉ ÉÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C SEATING PLANE RECOMMENDED SOLDERING FOOTPRINT* e/2 e 1 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.60 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.30 0.40 7X L 0.49 4 8X 0.26 L1 1.24 8 5 BOTTOM VIEW 8X b 0.10 M C A B 0.05 M C 0.53 NOTE 3 1 PKG OUTLINE 0.40 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 6 NLU3G16 PACKAGE DIMENSIONS UDFN8, 1.45x1, 0.35P CASE 517BZ ISSUE O PIN ONE REFERENCE 0.10 C 2X 2X 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D ÉÉ ÉÉ E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C SEATING PLANE RECOMMENDED SOLDERING FOOTPRINT* e/2 7X e 1 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.45 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 0.48 L 8X 0.22 4 L1 1.18 8 5 BOTTOM VIEW 8X b 0.10 M C A B 0.05 M C 0.53 1 PKG OUTLINE NOTE 3 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 7 NLU3G16 PACKAGE DIMENSIONS UDFN8, 1.95x1, 0.5P CASE 517CA ISSUE O PIN ONE REFERENCE 0.10 C 2X 2X ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C SEATING PLANE RECOMMENDED SOLDERING FOOTPRINT* e/2 e 7X 7X L 0.49 4 1 MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.95 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 8X 0.30 L1 1.24 8 5 BOTTOM VIEW 8X b 0.10 M C A B 0.05 M C 0.54 NOTE 3 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 8 NLU3G16 PACKAGE DIMENSIONS ULLGA8 1.95x1.0, 0.5P CASE 613AC ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉÉ ÉÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.15 0.25 1.95 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 A 8X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 7X e/2 e 7X L 0.49 NOTE 4 8X 0.30 4 1 L1 1.24 8 5 8X BOTTOM VIEW b 0.10 C A B 0.05 C 0.53 1 PKG OUTLINE NOTE 3 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLU3G16/D