NLV17SZ125DFT1G

DATA SHEET www.onsemi.com Non-Inverting 3-State Buffer MARKING DIAGRAMS NL17SZ125 The NL17SZ125 is a single non−inverting 3−state buffer in tiny footprint packages. SC−88A DF SUFFIX CASE 419A XX MG G SC−74A DBV SUFFIX CASE 318BQ XXX MG G Features • • • • • • • • • Designed for 1.65 V to 5.5 V VCC Operation 2.3 ns tPD at VCC = 5 V (typ) Inputs/Outputs Overvoltage Tolerant up to 5.5 V IOFF Supports Partial Power Down Protection Source/Sink 24 mA at 3.0 V Available in SC−88A, SC−74A, TSOP−5, SOT−553, SOT−953 and UDFN6 Packages Chip Complexity < 100 FETs NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant OE EN A 5 TSOP−5 DT SUFFIX CASE 483 5 1 XX MG G 1 SOT−553 XV5 SUFFIX CASE 463B SOT−953 P5 SUFFIX CASE 527AE Y XX MG G XM 1 UDFN6 1.45 x 1.0 CASE 517AQ Figure 1. Logic Symbol 1 UDFN6 1.0 x 1.0 CASE 517BX XX M G XM XM 1 = Specific Device Code = Date Code* = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. ORDERING INFORMATION See detailed ordering and shipping information on page 7 of this data sheet. © Semiconductor Components Industries, LLC, 2015 July, 2022 − Rev. 24 1 Publication Order Number: NL17SZ125/D NL17SZ125 VCC OE 1 5 A VCC A 5 1 OE 1 6 VCC A 2 5 NC GND 3 4 Y GND 2 2 GND Y 4 3 Y OE 4 3 SOT−953 (SC−88A/SOT−553/ TSOP−5/ SC−74A) UDFN6 Figure 2. Pinout (Top View) PIN ASSIGNMENT (SC−88A/SOT−553/ TSOP−5/SC−74A) PIN ASSIGNMENT (SOT−953) PIN ASSIGNMENT (UDFN) Pin Function Pin Function Pin Function 1 OE 1 A 1 OE 2 A 2 GND 2 A 3 GND 3 OE 3 GND 4 Y 4 Y 4 Y 5 VCC 5 VCC 5 NC 6 VCC FUNCTION TABLE Input Output OE A Y L L L L H H H X Z X = Don’t Care www.onsemi.com 2 NL17SZ125 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage (NLV) −0.5 to +7.0 −0.5 to +6.5 V VIN DC Input Voltage (NLV) −0.5 to +7.0 −0.5 to +6.5 V V VOUT Characteristics DC Output Voltage (NLV) Active−Mode (High or Low State) Tri−State Mode (Note 1) Power−Down Mode (VCC = 0 V) −0.5 to VCC + 0.5 −0.5 to +7.0 −0.5 to +7.0 DC Output Voltage (NL17SZ125P5T5G−L22088 Only) −0.5 to VCC + 0.5 DC Output Voltage Active−Mode (High or Low State) Tri−State Mode (Note 1) Power−Down Mode (VCC = 0 V) −0.5 to VCC + 0.5 −0.5 to +6.5 −0.5 to +6.5 IIK DC Input Diode Current IOK IOUT ICC or IGND TSTG VIN < GND −50 mA DC Output Diode Current VOUT < GND −50 mA DC Output Diode Current (NL17SZ125P5T5G−L22088 Only) ±50 DC Output Source/Sink Current ±50 mA DC Supply Current per Supply Pin or Ground Pin ±100 mA −65 to +150 °C TL Storage Temperature Range Lead Temperature, 1 mm from Case for 10 secs 260 °C TJ Junction Temperature Under Bias +150 °C qJA Thermal Resistance (Note 2) SC−88A SC−74A SOT−553 SOT−953 UDFN6 377 320 324 254 154 °C/W PD Power Dissipation in Still Air SC−88A SC−74A SOT−553 SOT−953 UDFN6 332 390 386 491 812 mW Level 1 − MSL Moisture Sensitivity FR Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in − ESD Withstand Voltage (Note 3) Human Body Model Charged Device Model 2000 1000 V $100 mA VESD ILatchup Latchup Performance (Note 4) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Applicable to devices with outputs that may be tri−stated. 2. Measured with minimum pad spacing on an FR4 board, using 10mm−by−1inch, 2 ounce copper trace no air flow per JESD51−7. 3. HBM tested to ANSI/ESDA/JEDEC JS−001−2017. CDM tested to EIA/JESD22−C101−F. JEDEC recommends that ESD qualification to EIA/JESD22−A115−A (Machine Model) be discontinued per JEDEC/JEP172A. 4. Tested to EIA/JESD78 Class II. www.onsemi.com 3 NL17SZ125 RECOMMENDED OPERATING CONDITIONS Symbol Characteristics VCC Positive DC Supply Voltage VIN DC Input Voltage VOUT TA tr , tf Min Max Unit 1.65 5.5 V 0 5.5 V DC Output Voltage Active−Mode (High or Low State) Tri−State Mode (Note 1) Power−Down Mode (VCC = 0 V) 0 0 0 VCC 5.5 5.5 V DC Output Voltage (NL17SZ125P5T5G−L22088 Only) 0 VCC Operating Temperature Range −55 +125 °C Input Rise and Fall Time (NLV) VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 0 0 100 20 ns/V Input Rise and Fall Time VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 0 0 0 0 20 20 10 5 Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. DC ELECTRICAL CHARACTERISTICS Symbol VIH VIL Parameter Condition VCC (V) TA = 255C Min −555C 3 TA 3 1255C Typ Max Min Max Units − − 0.75 x VCC − V High−Level Input Voltage (NLV and NL17SZ125P5T5G−L22088) 1.65 to 1.95 0.75 x VCC 0.70 x VCC − − 0.70 x VCC − High−Level Input Voltage 1.65 to 1.95 0.65 x VCC − − 0.65 x VCC − 2.3 to 5.5 2.3 to 5.5 0.70 x VCC − − 0.70 x VCC − Low−Level Input Voltage (NLV and NL17SZ125P5T5G−L22088) 1.65 to 1.95 − − 0.25 x VCC − 0.25 x VCC 2.3 to 5.5 − − 0.30 x VCC − 0.30 x VCC Low−Level Input Voltage 1.65 to 1.95 − − 0.35 x VCC − 0.35 x VCC 2.3 to 5.5 − − 0.30 x VCC − 0.30 x VCC VCC 1.4 2.1 2.4 2.7 2.5 4.0 − − − − − − − VCC − 0.1 1.29 1.9 2.2 2.4 2.3 3.8 − − − − − − − − − − − − − − 0.1 0.24 0.3 0.4 0.4 0.55 0.55 V V V VOH High−Level Output Voltage VIN = VIH or VIL IOH = −100 mA IOH = −4 mA IOH = −8 mA IOH = −12 mA IOH = −16 mA IOH = −24 mA IOH = −32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 VCC − 0.1 1.29 1.9 2.2 2.4 2.3 3.8 VOL Low−Level Output Voltage VIN = VIH or VIL IOL = 100 mA IOL = 4 mA IOL = 8 mA IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 − − − − − − − 0.08 0.2 0.22 0.28 0.38 0.42 0.1 0.24 0.3 0.4 0.4 0.55 0.55 IIN Input Leakage Current VIN = 5.5 V or GND 1.65 to 5.5 − − ±0.1 − ±1.0 mA IOZ 3−State Output Leakage Current VOUT = 0 V to 5.5 V 1.65 to 5.5 − − ±0.5 − ±5.0 mA www.onsemi.com 4 V V NL17SZ125 DC ELECTRICAL CHARACTERISTICS (continued) Symbol IOFF ICC Parameter Condition −555C 3 TA 3 1255C TA = 255C VCC (V) Min Typ Max Min Max Units Power Off Leakage Current VIN = 5.5 V or VOUT = 5.5 V 0 − − 1.0 − 10 mA Power Off Leakage Current (NL17SZ125P5T5G− L22088 Only) VIN = 5.5 V 0 − − 1.0 − 10 mA Quiescent Supply Current VIN = VCC or GND 5.5 − − 1.0 − 10 mA Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. AC ELECTRICAL CHARACTERISTICS Symbol tPLH, tPHL Min Typ RL = 1 MW, CL = 15 pF 1.65 to 1.95 − RL = 1 MW, CL = 15 pF 2.3 to 2.7 − RL = 1 MW, CL = 15 pF 3.0 to 3.6 Parameter Propagation Delay, A to Y (Figures 3 and 4) TA = 255C VCC (V) Condition Max Min Max Units 6.0 10 − 10.5 ns 3.4 7.5 − 8.0 − 2.5 5.2 − 5.5 − 2.9 5.7 − 6.0 − 2.0 4.5 − 4.8 − 2.3 5.0 − 5.3 1.65 to 1.95 − 6.5 9.5 − 10 2.3 to 2.7 − 3.6 8.5 − 9.0 3.0 to 3.6 − 2.8 6.2 − 6.5 4.5 to 5.5 − 2.0 5.5 − 5.8 1.65 to 1.95 − 5.0 10 − 10.5 2.3 to 2.7 − 3.3 8.0 − 8.5 3.0 to 3.6 − 2.7 5.7 − 6.0 2.6 4.7 − 5.0 RL = 500 W, CL = 50 pF 4.5 to 5.5 RL = 1 MW, CL = 15 pF RL = 500 W, CL = 50 pF tPZH, tPZL tPHZ, tPLZ Output Enable Time, OE to Y (Figures 3 and 4) Output Disable Time, OE to Y (Figures 3 and 4) −555C 3 TA 3 1255C 4.5 to 5.5 ns ns CAPACITIVE CHARACTERISTICS Symbol CIN Parameter Condition Typical Units Input Capacitance VCC = 5.5 V, VIN = 0 V or VCC 2.5 pF COUT Output Capacitance VCC = 5.5 V, VIN = 0 V or VCC 2.5 pF CPD Power Dissipation Capacitance (Note 5) 10 MHz, VCC = 3.3 V, VIN = 0 V or VCC 10 MHz, VCC = 5.5 V, VIN = 0 V or VCC 9 11 pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD  VCC  fin + ICC. CPD is used to determine the no−load dynamic power consumption; PD = CPD  VCC2  fin + ICC  VCC. www.onsemi.com 5 NL17SZ125 OPEN 2 x VCC Test Switch Position tPLH / tPHL Open tPLZ / tPZL 2 x VCC 50 500 500 tPHZ / tPZH GND 50 500 500 GND R1 OUTPUT DUT RL RT CL, pF RL, W R1 , W See AC Characteristics Table X = Don’t Care CL * CL includes probe and jig capacitance RT is ZOUT of pulse generator (typically 50 W) f = 1 MHz Figure 3. Test Circuit tr = 3 ns tf = 3 ns 90% 90% Vmi INPUT Vmi INPUT Vmi 10% 10% tPHL Vmi GND GND tPZL tPLH Vmo OUTPUT VCC VCC tPLZ ~VCC VOH Vmo OUTPUT Vmo VOL + VY VOL VOL tPLH OUTPUT tPHL Vmo tPZH VOH Vmo tPHZ VOH VOH − VY Vmo OUTPUT VOL ~0 V Figure 4. Switching Waveforms Vmo, V VCC, V Vmi, V tPLH, tPHL 1.65 to 1.95 VCC/2 VCC/2 VCC/2 0.15 2.3 to 2.7 VCC/2 VCC/2 VCC/2 0.15 3.0 to 3.6 VCC/2 VCC/2 VCC/2 0.3 4.5 to 5.5 VCC/2 VCC/2 VCC/2 0.3 www.onsemi.com 6 tPZL, tPLZ, tPZH, tPHZ VY, V NL17SZ125 DEVICE ORDERING INFORMATION Packages Specific Device Code Pin 1 Orientation (See below) Shipping† NL17SZ125DFT2G SC−88A M0 Q4 3000 / Tape & Reel NL17SZ125DFT2G−F22038** SC−88A M0 Q4 3000 / Tape & Reel NLV17SZ125DFT1G* SC−88A M0 Q2 3000 / Tape & Reel NLV17SZ125DFT2G* SC−88A M0 Q4 3000 / Tape & Reel NL17SZ125DBVT1G SC−74A M0 Q4 3000 / Tape & Reel NL17SZ125DTT1G** TSOP−5 M0 Q4 3000 / Tape & Reel NL17SZ125XV5T2G SOT−553 M0 Q4 4000 / Tape & Reel NL17SZ125XV5T2G−L22087** SOT−553 M0 Q4 4000 / Tape & Reel NL17SZ125P5T5G SOT−953 Q (Rotated 180° CW) Q2 8000 / Tape & Reel NL17SZ125P5T5G−L22088 SOT−953 Q (Rotated 180° CW) Q2 8000 / Tape & Reel NL17SZ125MU1TCG (In Development) UDFN6, 1.45 x 1.0, 0.5P TBD Q4 3000 / Tape & Reel NL17SZ125MU3TCG UDFN6, 1.0 x 1.0, 0.35P A Q4 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. ** Please refer to NLV specifications for this device. Pin 1 Orientation in Tape and Reel www.onsemi.com 7 NL17SZ125 PACKAGE DIMENSIONS SC−88A (SC−70−5/SOT−353) CASE 419A−02 ISSUE L A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 −B− S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) B M M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 J C K H SOLDER FOOTPRINT 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm Ǔ ǒinches STYLE 1: PIN 1. BASE 2. EMITTER 3. BASE 4. COLLECTOR 5. COLLECTOR STYLE 2: PIN 1. ANODE 2. EMITTER 3. BASE 4. COLLECTOR 5. CATHODE STYLE 3: PIN 1. ANODE 1 2. N/C 3. ANODE 2 4. CATHODE 2 5. CATHODE 1 STYLE 4: PIN 1. SOURCE 1 2. DRAIN 1/2 3. SOURCE 1 4. GATE 1 5. GATE 2 STYLE 6: PIN 1. EMITTER 2 2. BASE 2 3. EMITTER 1 4. COLLECTOR 5. COLLECTOR 2/BASE 1 STYLE 7: PIN 1. BASE 2. EMITTER 3. BASE 4. COLLECTOR 5. COLLECTOR STYLE 8: PIN 1. CATHODE 2. COLLECTOR 3. N/C 4. BASE 5. EMITTER STYLE 9: PIN 1. ANODE 2. CATHODE 3. ANODE 4. ANODE 5. ANODE www.onsemi.com 8 STYLE 5: PIN 1. CATHODE 2. COMMON ANODE 3. CATHODE 2 4. CATHODE 3 5. CATHODE 4 Note: Please refer to datasheet for style callout. If style type is not called out in the datasheet refer to the device datasheet pinout or pin assignment. NL17SZ125 PACKAGE DIMENSIONS SC−74A CASE 318BQ ISSUE B 5X b 0.20 C A B E1 5 M 4 1 2 E 3 B 0.05 A1 e A D L DETAIL A DIM A A1 b c D E E1 e L M TOP VIEW A SIDE VIEW C DETAIL A c SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. END VIEW MILLIMETERS MIN MAX 0.90 1.10 0.01 0.10 0.25 0.50 0.10 0.26 2.85 3.15 2.50 3.00 1.35 1.65 0.95 BSC 0.20 0.60 0_ 10 _ RECOMMENDED SOLDERING FOOTPRINT* 0.95 PITCH 2.40 5X 1.00 5X 0.70 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 9 NL17SZ125 PACKAGE DIMENSIONS TSOP−5 CASE 483 ISSUE N D NOTE 5 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSION A. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. 5X 0.20 C A B 0.10 T M 2X 0.20 T B 5 1 4 2 B S 3 K DETAIL Z G A A TOP VIEW DIM A B C D G H J K M S DETAIL Z J C 0.05 H SIDE VIEW C SEATING PLANE END VIEW MILLIMETERS MIN MAX 2.85 3.15 1.35 1.65 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 10 NL17SZ125 PACKAGE DIMENSIONS SOT−553, 5 LEAD CASE 463B ISSUE C D −X− 5 A 4 1 e 2 L E −Y− 3 b HE DIM A b c D E e L HE c 5 PL 0.08 (0.003) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. M X Y MILLIMETERS NOM MAX 0.55 0.60 0.22 0.27 0.13 0.18 1.60 1.65 1.20 1.25 0.50 BSC 0.10 0.20 0.30 1.55 1.60 1.65 MIN 0.50 0.17 0.08 1.55 1.15 SOLDERING FOOTPRINT* 0.3 0.0118 0.45 0.0177 1.35 0.0531 1.0 0.0394 0.5 0.5 0.0197 0.0197 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 11 INCHES NOM 0.022 0.009 0.005 0.063 0.047 0.020 BSC 0.004 0.008 0.061 0.063 MIN 0.020 0.007 0.003 0.061 0.045 MAX 0.024 0.011 0.007 0.065 0.049 0.012 0.065 NL17SZ125 PACKAGE DIMENSIONS SOT−953 CASE 527AE ISSUE E X D PIN ONE INDICATOR 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF THE BASE MATERIAL. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. A Y 4 HE E 1 2 3 DIM A b C D E e HE L L2 L3 C TOP VIEW SIDE VIEW e L 5X 5X L3 MILLIMETERS MIN NOM MAX 0.34 0.37 0.40 0.10 0.15 0.20 0.07 0.12 0.17 0.95 1.00 1.05 0.75 0.80 0.85 0.35 BSC 0.95 1.00 1.05 0.175 REF 0.05 0.10 0.15 −−− −−− 0.15 SOLDERING FOOTPRINT* 5X 0.35 5X 0.20 5X L2 5X BOTTOM VIEW b PACKAGE OUTLINE 0.08 X Y 1.20 1 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the onsemi Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 12 NL17SZ125 PACKAGE DIMENSIONS UDFN6, 1.45x1.0, 0.5P CASE 517AQ ISSUE O A B D PIN ONE REFERENCE 0.10 C DETAIL A E OPTIONAL CONSTRUCTIONS DIM A A1 A2 b D E e L L1 ÉÉ ÉÉ EXPOSED Cu TOP VIEW DETAIL B MOLD CMPD DETAIL B 0.05 C 6X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. L1 ÉÉÉ ÉÉÉ ÉÉÉ 0.10 C L L OPTIONAL CONSTRUCTIONS A MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.07 REF 0.20 0.30 1.45 BSC 1.00 BSC 0.50 BSC 0.30 0.40 −−− 0.15 MOUNTING FOOTPRINT 0.05 C A1 SIDE VIEW A2 e 6X C 6X SEATING PLANE L 1.24 3 1 DETAIL A 6X 0.53 6 0.30 PACKAGE OUTLINE 4 BOTTOM VIEW 6X 0.50 PITCH DIMENSIONS: MILLIMETERS b 0.10 C A B 0.05 C 1 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 www.onsemi.com 13 NL17SZ125 PACKAGE DIMENSIONS UDFN6, 1x1, 0.35P CASE 517BX ISSUE O PIN ONE REFERENCE 2X 0.10 C 2X 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D ÉÉ ÉÉ ÉÉ E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 0.05 C A1 SIDE VIEW C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 5X e 5X 0.48 L 6X 0.22 3 1 L1 1.18 6 4 6X BOTTOM VIEW b 0.10 M C A B 0.05 M C 0.53 1 PKG OUTLINE NOTE 3 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 14 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative