NRVTSM260E
Surface Mount Trench
Schottky Power Rectifier
POWERMITE®
Power Surface Mount Package
http://onsemi.com
Features
•
•
•
•
•
•
•
•
•
•
•
Low Profile − Maximum Height of 1.1 mm
Small Footprint − Footprint Area of 8.45 mm2
Supplied in 12 mm Tape and Reel
Low Thermal Resistance with Direct Thermal Path of Die on
Exposed Cathode Heat Sink
Fine Lithography Trench−based Schottky Technology for Very Low
Forward Voltage and Low Leakage
Fast Switching with Exceptional Temperature Stability
Low Power Loss and Lower Operating Temperature
Higher Efficiency for Achieving Regulatory Compliance
High Surge Capability
NRV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q101
Qualified and PPAP Capable
These are Pb−Free and Halide−Free Devices
SCHOTTKY TRENCH
RECTIFIER
2.0 AMPERES, 60 VOLTS
CATHODE
ANODE
POWERMITE
CASE 457
MARKING DIAGRAM
1
Typical Applications
•
•
•
•
•
Switching Power Supplies including Adapters & Flat Panel Displays
High Frequency and DC−DC Converters
Freewheeling and OR−ing diodes
Reverse Battery Protection
Instrumentation
M
AACG
2
M
= Date Code
AAC = Device Code
G
= Pb−Free Package
(Marking Style 1)
Mechanical Characteristics:
•
•
•
•
•
Powermite is JEDEC Registered as D0−216AA
Case: Molded Epoxy
Epoxy Meets UL 94 V−0 @ 0.125 in
Weight: 16.3 mg (Approximately)
Lead and Mounting Surface Temperature for Soldering Purposes:
260°C Maximum for 10 Seconds
ORDERING INFORMATION
Package
Shipping†
NRVTSM260ET1G
Powermite
(Pb−Free)
3000 / Tape &
Reel
NRVTSM260ET3G
Powermite
(Pb−Free)
12000 / Tape &
Reel
Device
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2014
August, 2014 − Rev. 2
1
Publication Order Number:
NRVTSM260/D
NRVTSM260E
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VRRM
VRWM
VR
60
V
Average Rectified Forward Current
(TL = 162°C)
IO
2.0
A
Peak Repetitive Forward Current
(Square Wave, 20 kHz, TL = 160°C)
IFRM
4.0
A
Non−Repetitive Peak Surge Current
(Surge Applied at Rated Load Conditions Halfwave, Single Phase, 60 Hz)
IFSM
50
A
Tstg, TJ
−55 to +175
°C
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
Storage and Operating Junction Temperature Range (Note 1)
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. The heat generated must be less than the thermal conductivity from
Junction−to−Ambient: dPD/dTJ < 1/RqJA.
THERMAL CHARACTERISTICS
Characteristic
Symbol
Value
Unit
Thermal Resistance, Junction−to−Lead (Note 2)
YJCL
8.6
°C/W
Thermal Resistance, Junction−to−Ambient (Note 2)
RqJA
80
°C/W
Thermal Resistance, Junction−to−Ambient (Note 3)
RqJA
237
°C/W
Symbol
Value
Unit
ELECTRICAL CHARACTERISTICS
Characteristic
VF
Maximum Instantaneous Forward Voltage (Note 4)
(IF = 1 A, TJ = 25°C)
(IF = 2 A, TJ = 25°C)
V
0.55
0.65
0.47
0.58
(IF = 1 A, TJ = 125°C)
(IF = 2 A, TJ = 125°C)
Maximum Instantaneous Reverse Current (Note 4)
(Rated dc Voltage, TJ = 25°C)
(Rated dc Voltage, TJ = 125°C)
IR
12
3.0
mA
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Mounted with 700 mm2 copper pad size (Approximately 1 in2) 1 oz FR4 Board.
3. Mounted with pad size approximately 20 mm2 copper, 1 oz FR4 Board.
4. Pulse Test: Pulse Width ≤ 380 ms, Duty Cycle ≤ 2.0%.
http://onsemi.com
2
NRVTSM260E
TYPICAL CHARACTERISTICS
100
iF, INSTANTANEOUS FORWARD
CURRENT (A)
iF, INSTANTANEOUS FORWARD
CURRENT (A)
100
TJ = 175°C
10
TJ = 150°C
TJ = 125°C
TJ = 85°C
1
TJ = 25°C
TJ = −55°C
0.1
0.1
0.3
0.5
0.7
0.9
1.1
1.3
VF, INSTANTANEOUS FORWARD VOLTAGE (V)
TJ = 175°C
TJ = 125°C
TJ = 85°C
1
TJ = 25°C
TJ = −55°C
0.1
1.5
TJ = 150°C
10
0.2
1.E−01
1.E−01
1.E−02
TJ = 175°C
1.E−02
TJ = 175°C
TJ = 150°C
1.E−03
TJ = 125°C
1.E−04
TJ = 85°C
1.E−05
TJ = 150°C
1.E−03
TJ = 125°C
1.E−04
TJ = 85°C
1.E−05
1.E−06
10
TJ = 25°C
1.E−06
TJ = 25°C
1.E−07
20
30
40
50
60
VR, INSTANTANEOUS REVERSE VOLTAGE (V)
1.E−07
10
1000
TJ = 25°C
100
10
0.1
1
20
30
40
50
VR, INSTANTANEOUS REVERSE VOLTAGE (V)
60
Figure 4. Maximum Reverse Characteristics
IF(AV), AVERAGE FORWARD CURRENT (A)
Figure 3. Typical Reverse Characteristics
C, JUNCTION CAPACITANCE (pF)
1.6
Figure 2. Maximum Instantaneous Forward
Characteristics
IF, INSTANTANEOUS REVERSE CURRENT (A)
IR, INSTANTANEOUS REVERSE CURRENT (A)
Figure 1. Typical Instantaneous Forward
Characteristics
0.4
0.6
0.8
1.0
1.2
1.4
VF, INSTANTANEOUS FORWARD VOLTAGE (V)
10
5
RqJC = 25°C/W
4
dc
3
SQUARE WAVE
2
1
0
100
VR, REVERSE VOLTAGE (V)
110
120
130
140
150
160
TC, CASE TEMPERATURE (°C)
Figure 6. Current Derating
Figure 5. Typical Junction Capacitance
http://onsemi.com
3
170
NRVTSM260E
PF(AV), AVERAGE POWER DISSIPATION (W)
TYPICAL CHARACTERISTICS
6
IPK/IAV = 20
TJ = 175°C
IPK/IAV = 10
4
IPK/IAV = 5
2
SQUARE WAVE
dc
0
0
0.5
1.0
2.0
2.5
1.5
IF(AV), AVERAGE FORWARD CURRENT (A)
3.0
Figure 7. Forward Power Dissipation
1000
50% (DUTY CYCLE)
R(t) (°C/W)
100
10
20%
10%
5.0%
2.0%
1.0%
1
SINGLE PULSE
0.1
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
10
100
1000
100
1000
t, PULSE TIME (s)
Figure 8. Thermal Response, Junction−to−Ambient (20 mm2 pad)
100
50% (DUTY CYCLE)
20%
R(t) (°C/W)
10
10%
5.0%
2.0%
1
1.0%
SINGLE PULSE
0.1
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
t, PULSE TIME (s)
Figure 9. Thermal Response, Junction−to−Ambient (1 in2 pad)
POWERMITE is a registered trademark of and used under a license from Microsemi Corporation.
http://onsemi.com
4
10
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
POWERMITE
CASE 457
ISSUE G
DATE 12 JAN 2022
SCALE 4:1
GENERIC
MARKING DIAGRAMS*
1
M
XXXG
2
1
STYLE 1
1
M
XXXG
2
STYLE 2
M
XXXG
2
XXX = Specific Device Code
M = Date Code
G
= Pb−Free Package
STYLE 3
DOCUMENT NUMBER:
DESCRIPTION:
STYLE 1:
PIN 1. CATHODE
2. ANODE
98ASB14853C
POWERMITE
STYLE 2:
PIN 1. ANODE OR CATHODE
2. CATHODE OR ANODE
(BI−DIRECTIONAL)
STYLE 3:
PIN 1. ANODE
2. CATHODE
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
onsemi and
are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves
the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
