NVD5865NLT4G

NVD5865NL Power MOSFET 60 V, 46 A, 16 mW, Single N−Channel Features • • • • • Low RDS(on) to Minimize Conduction Losses High Current Capability Avalanche Energy Specified AEC−Q101 Qualified These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant www.onsemi.com RDS(on) V(BR)DSS ID 16 mW @ 10 V 60 V 46 A 19 mW @ 4.5 V MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Symbol Value Unit Drain−to−Source Voltage VDSS 60 V Gate−to−Source Voltage VGS "20 V ID 46 A Continuous Drain Current RqJC (Notes 1 & 3) Power Dissipation RqJC (Note 1) Continuous Drain Current RqJA (Notes 1, 2 & 3) Power Dissipation RqJA (Notes 1 & 2) TC = 25°C Steady State TC = 100°C TC = 25°C Steady State PD W 71 36 ID TA = 100°C TA = 25°C 4 7.0 PD TA = 100°C W 3.1 203 A TA = 25°C IDmaxpkg 60 A TJ, Tstg −55 to 175 °C IS 46 A Single Pulse Drain−to−Source Avalanche Energy (L = 0.1 mH) EAS 36 mJ IAS 27 A Lead Temperature for Soldering Purposes (1/8″ from case for 10 s) TL 260 °C Operating Junction and Storage Temperature Source Current (Body Diode) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. THERMAL RESISTANCE MAXIMUM RATINGS Parameter 1 2 3 1.5 IDM Current Limited by Package (Note 3) S N−CHANNEL MOSFET A 10 TA = 25°C, tp = 10 ms Pulsed Drain Current G 33 TC = 100°C TA = 25°C D Symbol Value Unit Junction−to−Case (Drain) (Note 1) RqJC 2.1 °C/W Junction−to−Ambient − Steady State (Note 2) RqJA 49 1. The entire application environment impacts the thermal resistance values shown, they are not constants and are only valid for the particular conditions noted. 2. Surface−mounted on FR4 board using a 650 mm2, 2 oz. Cu pad. 3. Maximum current for pulses as long as 1 second is higher but is dependent on pulse duration and duty cycle. DPAK CASE 369AA STYLE 2 MARKING DIAGRAM & PIN ASSIGNMENT 4 Drain AYWW V58 65LG Parameter 2 1 Drain 3 Gate Source A = Assembly Location* Y = Year WW = Work Week V5865L = Device Code G = Pb−Free Package * The Assembly Location code (A) is front side optional. In cases where the Assembly Location is stamped in the package, the front side assembly code may be blank. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. © Semiconductor Components Industries, LLC, 2016 September, 2016 − Rev. 4 1 Publication Order Number: NVD5865NL/D NVD5865NL ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Symbol Test Condition Min Drain−to−Source Breakdown Voltage V(BR)DSS VGS = 0 V, ID = 250 mA 60 Drain−to−Source Breakdown Voltage Temperature Coefficient V(BR)DSS/TJ Parameter Typ Max Unit OFF CHARACTERISTICS Zero Gate Voltage Drain Current 55 IDSS Gate−to−Source Leakage Current V VGS = 0 V, VDS = 60 V mV/°C TJ = 25°C 1.0 TJ = 125°C 100 IGSS VDS = 0 V, VGS = ±20 V VGS(TH) VGS = VDS, ID = 250 mA mA ±100 nA 2.0 V ON CHARACTERISTICS (Note 4) Gate Threshold Voltage Negative Threshold Temperature Coefficient VGS(TH)/TJ 1.0 5.6 mV/°C Drain−to−Source On Resistance RDS(on) VGS = 10 V, ID = 19 A 13 16 mW Drain−to−Source on Resistance RDS(on) VGS = 4.5 V, ID = 19 A 16 19 mW gFS VDS = 15 V, ID = 19 A 15 S 1400 pF Forward Transconductance CHARGES, CAPACITANCES AND GATE RESISTANCES Input Capacitance Ciss VGS = 0 V, f = 1.0 MHz, VDS = 25 V Output Capacitance Coss Reverse Transfer Capacitance Crss 95 Total Gate Charge QG(TOT) 29 Threshold Gate Charge QG(TH) Gate−to−Source Charge QGS Gate−to−Drain Charge QGD Total Gate Charge Gate Resistance QG(TOT) VGS = 10 V, VDS = 48 V, ID = 38 A 137 nC 1.1 4 8 VGS = 4.5 V, VDS = 48 V, ID = 38 A 15 nC RG 1.3 W td(on) 8.4 ns SWITCHING CHARACTERISTICS (Note 5) Turn−On Delay Time Rise Time Turn−Off Delay Time Fall Time tr td(off) VGS = 10 V, VDD = 48 V, ID = 38 A, RG = 2.5 W tf 12.4 26 4.4 DRAIN−SOURCE DIODE CHARACTERISTICS Forward Diode Voltage Reverse Recovery Time Charge Time Discharge Time Reverse Recovery Charge VSD VGS = 0 V, IS = 38 A TJ = 25°C 0.95 TJ = 125°C 0.85 tRR ta tb 20 VGS = 0 V, dIs/dt = 100 A/ms, IS = 38 A QRR 1.2 V ns 13 7 13 nC Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. 4. Pulse Test: Pulse Width ≤ 300 ms, Duty Cycle ≤ 2%. 5. Switching characteristics are independent of operating junction temperatures. www.onsemi.com 2 NVD5865NL TYPICAL CHARACTERISTICS 80 3.8 V 3.6 V 50 3.4 V 40 3.2 V 30 20 3V 10 2.8 V 1 2 3 4 30 TJ = 25°C 20 5 TJ = 125°C 1 TJ = −55°C 2 3 4 5 VGS, GATE−TO−SOURCE VOLTAGE (V) Figure 1. On−Region Characteristics Figure 2. Transfer Characteristics ID = 38 A TJ = 25°C 0.025 0.020 0.015 0.010 3 4 5 6 7 8 9 10 0.018 TJ = 25°C VGS = 4.5 V 0.016 0.014 VGS = 10 V 0.012 0.010 5 10 15 20 25 30 35 VGS, GATE−TO−SOURCE VOLTAGE (V) ID, DRAIN CURRENT (A) Figure 3. On−Resistance vs. Gate Voltage Figure 4. On−Resistance vs. Drain Current 40 10000 2.2 2.0 40 VDS, DRAIN−TO−SOURCE VOLTAGE (V) 0.030 2 50 0 ID = 38 A VGS = 10 V VGS = 0 V TJ = 150°C 1.8 IDSS, LEAKAGE (nA) RDS(on), DRAIN−TO−SOURCE RESISTANCE (W) 0 60 10 2.6 V 0 RDS(on), DRAIN−TO−SOURCE RESISTANCE (NORMALIZED) ID, DRAIN CURRENT (A) 4.5 V 60 VDS ≥ 10 V 70 TJ = 25°C RDS(on), DRAIN−TO−SOURCE RESISTANCE (W) ID, DRAIN CURRENT (A) 70 80 4V VGS = 10 V 1.6 1.4 1.2 1.0 1000 TJ = 125°C 0.8 0.6 −50 100 −25 0 25 50 75 100 125 150 175 10 20 30 40 50 TJ, JUNCTION TEMPERATURE (°C) VDS, DRAIN−TO−SOURCE VOLTAGE (V) Figure 5. On−Resistance Variation with Temperature Figure 6. Drain−to−Source Leakage Current vs. Voltage www.onsemi.com 3 60 NVD5865NL TYPICAL CHARACTERISTICS 10 VGS = 0 V TJ = 25°C 1600 Ciss C, CAPACITANCE (pF) 1400 VGS, GATE−TO−SOURCE VOLTAGE (V) 1800 1200 1000 800 600 400 Coss 200 Crss 0 0 10 20 30 40 50 60 8 6 4 Qgs Qgd 2 VDS = 48 V ID = 38 A TJ = 25°C 0 0 5 10 15 20 25 VDS, DRAIN−TO−SOURCE VOLTAGE (V) Qg, TOTAL GATE CHARGE (nC) Figure 7. Capacitance Variation Figure 8. Gate−to−Source vs. Total Charge 1000 30 40 VDD = 48 V ID = 38 A VGS = 10 V IS, SOURCE CURRENT (A) td(off) tr 10 VGS = 0 V 35 100 td(on) tf 1 10 TJ = 25°C 30 25 20 15 10 5 0 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 1 100 RG, GATE RESISTANCE (W) VSD, SOURCE−TO−DRAIN VOLTAGE (V) Figure 9. Resistive Switching Time Variation vs. Gate Resistance Figure 10. Diode Forward Voltage vs. Current 1000 ID, DRAIN CURRENT (A) t, TIME (ns) QT 100 VGS = 10 V SINGLE PULSE TC = 25°C 100 ms 10 ms 10 ms 1 ms 10 dc 1 RDS(on) LIMIT THERMAL LIMIT PACKAGE LIMIT 0.1 0.1 1 10 VDS, DRAIN−TO−SOURCE VOLTAGE (V) Figure 11. Maximum Rated Forward Biased Safe Operating Area www.onsemi.com 4 100 NVD5865NL TYPICAL CHARACTERISTICS RqJC(t) (°C/W) EFFECTIVE TRANSIENT THERMAL RESISTANCE 10 Duty Cycle = 0.5 1 0.2 0.1 0.05 0.1 0.02 0.01 SINGLE PULSE 0.01 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 1000 t, PULSE TIME (s) Figure 12. Thermal Response ORDERING INFORMATION Package Shipping† NVD5865NLT4G DPAK (Pb−Free) 2500 / Tape & Reel SVD5865NLT4G DPAK (Pb−Free) 2500 / Tape & Reel Order Number †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 5 NVD5865NL PACKAGE DIMENSIONS DPAK (SINGLE GUAGE) CASE 369AA ISSUE B NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. THERMAL PAD CONTOUR OPTIONAL WITHIN DIMENSIONS b3, L3 and Z. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.006 INCHES PER SIDE. 5. DIMENSIONS D AND E ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY. 6. DATUMS A AND B ARE DETERMINED AT DATUM PLANE H. C A A E b3 c2 B 4 L3 Z D 1 2 H DETAIL A 3 L4 b2 e c b 0.005 (0.13) M C H L2 GAUGE PLANE C L SEATING PLANE A1 L1 DETAIL A ROTATED 905 CW 2.58 0.102 5.80 0.228 3.00 0.118 1.60 0.063 INCHES MIN MAX 0.086 0.094 0.000 0.005 0.025 0.035 0.030 0.045 0.180 0.215 0.018 0.024 0.018 0.024 0.235 0.245 0.250 0.265 0.090 BSC 0.370 0.410 0.055 0.070 0.108 REF 0.020 BSC 0.035 0.050 −−− 0.040 0.155 −−− MILLIMETERS MIN MAX 2.18 2.38 0.00 0.13 0.63 0.89 0.76 1.14 4.57 5.46 0.46 0.61 0.46 0.61 5.97 6.22 6.35 6.73 2.29 BSC 9.40 10.41 1.40 1.78 2.74 REF 0.51 BSC 0.89 1.27 −−− 1.01 3.93 −−− STYLE 2: PIN 1. GATE 2. DRAIN 3. SOURCE 4. DRAIN SOLDERING FOOTPRINT* 6.20 0.244 DIM A A1 b b2 b3 c c2 D E e H L L1 L2 L3 L4 Z 6.17 0.243 SCALE 3:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ◊ N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NVD5865NL/D