NVGS3443T1G

NTGS3443, NVGS3443 Power MOSFET 4.4 Amps, 20 Volts P−Channel TSOP−6 http://onsemi.com Features • • • • • Ultra Low RDS(on) Higher Efficiency Extending Battery Life Miniature TSOP−6 Surface Mount Package These Devices are Pb−Free and are RoHS Compliant NVGS Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q101 Qualified and PPAP Capable 4.4 AMPERES 20 VOLTS RDS(on) = 65 mW P−Channel 1 2 5 6 Applications • Power Management in Portable and Battery−Powered Products, 3 i.e.: Cellular and Cordless Telephones, and PCMCIA Cards MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating 4 Symbol Value Unit Drain−to−Source Voltage VDSS −20 Volts Gate−to−Source Voltage − Continuous VGS "12 Volts Thermal Resistance Junction−to−Ambient (Note 1) Total Power Dissipation @ TA = 25°C Drain Current − Continuous @ TA = 25°C − Pulsed Drain Current (Tp t 10 mS) RqJA Pd ID IDM 244 0.5 −2.2 −10 °C/W Watts Amps Amps Thermal Resistance Junction−to−Ambient (Note 2) Total Power Dissipation @ TA = 25°C Drain Current − Continuous @ TA = 25°C − Pulsed Drain Current (Tp t 10 mS) RqJA Pd ID IDM 128 1.0 −3.1 −14 °C/W Watts Amps Amps Thermal Resistance Junction−to−Ambient (Note 3) Total Power Dissipation @ TA = 25°C Drain Current − Continuous @ TA = 25°C − Pulsed Drain Current (Tp t 10 mS) RqJA Pd ID IDM 62.5 2.0 −4.4 −20 °C/W Watts Amps Amps Operating and Storage Temperature Range TJ, Tstg −55 to 150 °C Maximum Lead Temperature for Soldering Purposes for 10 Seconds TL 260 °C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Minimum FR−4 or G−10 PCB, operating to steady state. 2. Mounted onto a 2 in square FR−4 board (1 in sq, 2 oz. Cu. 0.06″ thick single sided), operating to steady state. 3. Mounted onto a 2 in square FR−4 board (1 in sq, 2 oz. Cu. 0.06″ thick single sided), t t 5.0 seconds. © Semiconductor Components Industries, LLC, 2012 December, 2012 − Rev. 5 1 MARKING DIAGRAM & PIN ASSIGNMENT Drain Drain Source 6 5 4 443 M G G 1 TSOP−6 CASE 318G STYLE 1 1 2 3 Drain Drain Gate 443 = Specific Device Code M = Date Code* G = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation may vary depending upon manufacturing location. ORDERING INFORMATION Device Package Shipping† NTGS3443T1G TSOP−6 (Pb−Free) 3000 / Tape & Reel NVGS3443T1G TSOP−6 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Publication Order Number: NTGS3443T1/D NTGS3443, NVGS3443 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) (Notes 4 & 5) Symbol Min Typ Max −20 − − − − − − −1.0 −5.0 − − −100 − − 100 −0.60 −0.95 −1.50 − − − 0.058 0.082 0.092 0.065 0.090 0.100 − 8.8 − Ciss − 565 − pF Coss − 320 − pF Crss − 120 − pF td(on) − 10 25 ns tr − 18 45 ns td(off) − 30 50 ns tf − 31 50 ns Qtot − 7.5 15 nC Qgs − 1.4 − nC Qgd − 2.9 − nC (IS = −1.7 Adc, VGS = 0 Vdc) VSD − −0.83 −1.2 Vdc (IS = −1.7 Adc, dIS/dt = 100 A/ms) trr − 30 − ns Characteristic Unit OFF CHARACTERISTICS Drain−Source Breakdown Voltage (VGS = 0 Vdc, ID = −10 mA) V(BR)DSS Zero Gate Voltage Drain Current (VGS = 0 Vdc, VDS = −20 Vdc, TJ = 25°C) (VGS = 0 Vdc, VDS = −20 Vdc, TJ = 70°C) IDSS Gate−Body Leakage Current (VGS = −12 Vdc, VDS = 0 Vdc) IGSS Gate−Body Leakage Current (VGS = +12 Vdc, VDS = 0 Vdc) IGSS Vdc mAdc nAdc nAdc ON CHARACTERISTICS Gate Threshold Voltage (VDS = VGS, ID = −250 mAdc) VGS(th) Static Drain−Source On−State Resistance (VGS = −4.5 Vdc, ID = −4.4 Adc) (VGS = −2.7 Vdc, ID = −3.7 Adc) (VGS = −2.5 Vdc, ID = −3.5 Adc) RDS(on) Forward Transconductance (VDS = −10 Vdc, ID = −4.4 Adc) gFS Vdc W mhos DYNAMIC CHARACTERISTICS Input Capacitance Output Capacitance (VDS = −5.0 Vdc, VGS = 0 Vdc, f = 1.0 MHz) Reverse Transfer Capacitance SWITCHING CHARACTERISTICS Turn−On Delay Time Rise Time Turn−Off Delay Time (VDD = −20 Vdc, ID = −1.0 Adc, VGS = −4.5 Vdc, Rg = 6.0 W) Fall Time Total Gate Charge Gate−Source Charge Gate−Drain Charge (VDS = −10 Vdc, VGS = −4.5 Vdc, ID = −4.4 Adc) BODY−DRAIN DIODE RATINGS Diode Forward On−Voltage Reverse Recovery Time 4. Indicates Pulse Test: P.W. = 300 msec max, Duty Cycle = 2%. 5. Handling precautions to protect against electrostatic discharge are mandatory. http://onsemi.com 2 NTGS3443, NVGS3443 TYPICAL ELECTRICAL CHARACTERISTICS −ID, DRAIN CURRENT (AMPS) VDS≥ = −10 V TJ = 25°C VGS = −3 V VGS = −4.5 V VGS = −4 V VGS = −3.5 V VGS = −2 V 4 2 VGS = −1.5 V 0 0.4 0.8 1.2 1.6 4 TJ = 25°C 2 TJ = 125°C 0 0.6 1.4 1.8 2.2 Figure 1. On−Region Characteristics Figure 2. Transfer Characteristics ID = −4.4 A TJ = 25°C 0.3 0.25 0.2 0.15 0.1 0.05 2 2.5 3 3.5 4 4.5 5 −VGS, GATE−TO−SOURCE VOLTAGE (VOLTS) 3 0.16 TJ = 25°C 0.14 VGS = −2.5 V 0.12 VGS = −2.7 V 0.1 0.08 VGS = −4.5 V 0.06 0.04 0 1 2 3 4 5 6 7 8 −ID, DRAIN CURRENT (AMPS) Figure 3. On−Resistance vs. Gate−to−Source Voltage Figure 4. On−Resistance vs. Drain Current and Gate Voltage 100 1.5 TJ = 125°C ID = −4.4 A VGS = −4.5 V 1.3 1.2 1.1 1 0.9 TJ = 100°C 10 1 TJ = 25°C 0.1 0.8 0.7 −50 2.6 −VGS, GATE−TO−SOURCE VOLTAGE (VOLTS) 0.35 1.4 1 TJ = −55°C −VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS) 0.4 0 1.5 6 2 RDS(on), DRAIN−TO−SOURCE RESISTANCE (OHMS) RDS(on), DRAIN−TO−SOURCE RESISTANCE (OHMS) VGS = −2.5 V 6 0 RDS(on), DRAIN−TO−SOURCE RESISTANCE (NORMALIZED) 8 VGS = −5 V −IDSS, LEAKAGE (nA) −ID, DRAIN CURRENT (AMPS) 8 VGS = 0 V −25 0 25 50 75 100 125 0.01 150 0 4 8 12 16 TJ, JUNCTION TEMPERATURE (°C) −VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS) Figure 5. On−Resistance Variation with Temperature Figure 6. Drain−to−Source Leakage Current vs. Voltage http://onsemi.com 3 20 NTGS3443, NVGS3443 TYPICAL ELECTRICAL CHARACTERISTICS 5 1200 800 600 Ciss 400 Coss 200 VGS(th), GATE THRESHOLD VOLTAGE (NORMALIZED) 0 QT VGS 4 3 Q1 Q2 2 1 TJ = 25°C ID = −4.4 A Crss 0 2 4 6 8 10 12 14 16 18 0 20 1 2 3 4 5 6 7 Qg, TOTAL GATE CHARGE (nC) Figure 7. Capacitance Variation Figure 8. Gate−to−Source and Drain−to−Source Voltage vs. Total Charge 1.3 4 ID = −250 mA 1.2 1.1 1 0.9 0.8 0.7 0.6 −50 0 −VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS) −IS, SOURCE CURRENT (AMPS) C, CAPACITANCE (pF) 1000 −VGS, GATE−TO−SOURCE VOLTAGE (VOLTS) TJ = 25°C VGS = 0 V −25 0 25 50 75 100 125 150 VGS = 0 V 3 TJ = 150°C 2 TJ = 25°C 1 0 0.3 0.4 0.5 0.6 0.7 0.8 0.9 TJ, JUNCTION TEMPERATURE (°C) −VSD, SOURCE−TO−DRAIN VOLTAGE (VOLTS) Figure 9. Gate Threshold Voltage Variation with Temperature Figure 10. Diode Forward Voltage vs. Current http://onsemi.com 4 8 1 NTGS3443, NVGS3443 TYPICAL ELECTRICAL CHARACTERISTICS 20 POWER (W) 16 12 8 4 0 0.01 0.10 1.00 10.00 100.00 TIME (sec) NORMALIZED EFFECTIVE TRANSIENT THERMAL IMPEDANCE Figure 11. Single Pulse Power 1 Duty Cycle = 0.5 0.2 0.1 0.1 0.05 0.02 0.01 0.01 1E−04 Single Pulse 1E−03 1E−02 1E−01 1E+00 1E+01 1E+02 SQUARE WAVE PULSE DURATION (sec) Figure 12. Normalized Thermal Transient Impedance, Junction−to−Ambient http://onsemi.com 5 1E+03 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS TSOP−6 CASE 318G−02 ISSUE V 1 SCALE 2:1 D H ÉÉ ÉÉ 6 E1 1 NOTE 5 5 2 L2 4 GAUGE PLANE E 3 L b SEATING PLANE C DETAIL Z e DIM A A1 b c D E E1 e L L2 M c A 0.05 M DATE 12 JUN 2012 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSIONS D AND E1 ARE DETERMINED AT DATUM H. 5. PIN ONE INDICATOR MUST BE LOCATED IN THE INDICATED ZONE. A1 DETAIL Z MIN 0.90 0.01 0.25 0.10 2.90 2.50 1.30 0.85 0.20 0° MILLIMETERS NOM MAX 1.00 1.10 0.06 0.10 0.38 0.50 0.18 0.26 3.00 3.10 2.75 3.00 1.50 1.70 0.95 1.05 0.40 0.60 0.25 BSC 10° − STYLE 1: PIN 1. DRAIN 2. DRAIN 3. GATE 4. SOURCE 5. DRAIN 6. DRAIN STYLE 2: PIN 1. EMITTER 2 2. BASE 1 3. COLLECTOR 1 4. EMITTER 1 5. BASE 2 6. COLLECTOR 2 STYLE 3: PIN 1. ENABLE 2. N/C 3. R BOOST 4. Vz 5. V in 6. V out STYLE 4: PIN 1. N/C 2. V in 3. NOT USED 4. GROUND 5. ENABLE 6. LOAD STYLE 5: PIN 1. EMITTER 2 2. BASE 2 3. COLLECTOR 1 4. EMITTER 1 5. BASE 1 6. COLLECTOR 2 STYLE 6: PIN 1. COLLECTOR 2. COLLECTOR 3. BASE 4. EMITTER 5. COLLECTOR 6. COLLECTOR STYLE 7: PIN 1. COLLECTOR 2. COLLECTOR 3. BASE 4. N/C 5. COLLECTOR 6. EMITTER STYLE 8: PIN 1. Vbus 2. D(in) 3. D(in)+ 4. D(out)+ 5. D(out) 6. GND STYLE 9: PIN 1. LOW VOLTAGE GATE 2. DRAIN 3. SOURCE 4. DRAIN 5. DRAIN 6. HIGH VOLTAGE GATE STYLE 10: PIN 1. D(OUT)+ 2. GND 3. D(OUT)− 4. D(IN)− 5. VBUS 6. D(IN)+ STYLE 11: PIN 1. SOURCE 1 2. DRAIN 2 3. DRAIN 2 4. SOURCE 2 5. GATE 1 6. DRAIN 1/GATE 2 STYLE 12: PIN 1. I/O 2. GROUND 3. I/O 4. I/O 5. VCC 6. I/O STYLE 13: PIN 1. GATE 1 2. SOURCE 2 3. GATE 2 4. DRAIN 2 5. SOURCE 1 6. DRAIN 1 STYLE 14: PIN 1. ANODE 2. SOURCE 3. GATE 4. CATHODE/DRAIN 5. CATHODE/DRAIN 6. CATHODE/DRAIN STYLE 15: PIN 1. ANODE 2. SOURCE 3. GATE 4. DRAIN 5. N/C 6. CATHODE STYLE 16: PIN 1. ANODE/CATHODE 2. BASE 3. EMITTER 4. COLLECTOR 5. ANODE 6. CATHODE STYLE 17: PIN 1. EMITTER 2. BASE 3. ANODE/CATHODE 4. ANODE 5. CATHODE 6. COLLECTOR GENERIC MARKING DIAGRAM* RECOMMENDED SOLDERING FOOTPRINT* 6X 0.60 XXXAYWG G 1 6X 3.20 XXX A Y W G 0.95 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: 98ASB14888C TSOP−6 1 IC 0.95 XXX MG G = Specific Device Code =Assembly Location = Year = Work Week = Pb−Free Package STANDARD XXX = Specific Device Code M = Date Code G = Pb−Free Package *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. © Semiconductor Components Industries, LLC, 2019 www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative