TRP3FE0L1C00000

Fast Ethernet SFP Multimode Transceivers TRPNFEMM Product Description The TRPNFEMM series of fiber optic transceivers provide a quick and reliable interface for 100BASE-FX Fast Ethernet multimode applications. The transceivers connect to standard 20-pad SFP connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different types of transceivers without removing the power supply from the host system. The transceivers have bail-type latches, which offer an easy and convenient way to release the modules. The latch is compliant with the SFP MSA. The transmitter design incorporates a highly reliable 1310nm LED and a driver circuit. The receiver features a low noise transimpedance amplifier IC for high sensitivity and wide dynamic range. The transmitter and receiver DATA interfaces are AC-coupled internally. LV-TTL Transmitter Disable control input and Loss of Signal output interfaces are also provided. The transceivers operate from a single +3.3V power supply over three operating case temperature ranges of -5°C to +70°C (“B” option), -5°C to +85°C (“E” option) or -40°C to +85°C (“A” option). The housing is made of plastic and metal for EMI immunity. Features  Compliant with SFP MSA  Designed for Fast Ethernet 100BASE-FX Applications  1310nm LED Transmitter  Hot-pluggable  Excellent EMI & ESD Protection  Loss of Signal Output  Distances up to 2km  TX Disable Input  Duplex LC Optical Interface  Single +3.3V Power Supply Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature 1 Supply Voltage Input Voltage 1 Symbol Tst “B” option “E” option “A” option Vcc Vin Top Minimum - 40 -5 -5 - 40 0 0 Maximum + 85 + 70 + 85 + 85 + 5.0 Vcc Units °C °C V V Measured on top side of SFP module at the front center vent hole of the cage. An Oplink Company RevB-P.2009.06.23 TRPNFEMM Transmitter Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate Parameter Operating Data Rate 1 Optical Output Power Center Wavelength 3 Spectral Width (FWHM) Extinction Ratio Optical Output Power of OFF Transmitter Duty Cycle Distortion Jitter (peak-to-peak) Data Dependent Jitter (peak-to-peak) Random Jitter (peak-to-peak) Transmitter Output Eye 5 1 2 Symbol B PO λC Minimum - 19.0 1270 0.6 10 - Typical 125 - 16.0 140 - Maximum - 14.0 1380 3.0 - 45.0 1.0 0.6 0.76 Units Mb/s dBm nm nm ns dB dBm ns ns ns 2 3 3 ΔλRMS tr, tf Phi/Plo POFF DCD DDJ RJ Optical Rise/Fall Time (10% to 90%) 4 Typically compliant with OC-3/STM-1 eye mask (GR-253-CORE and G. 957) without filter, but not guaranteed and not tested for. Data rate ranges from 50Mb/s to 266Mb/s. However, some degradation may be incurred in overall performance. Measured average power coupled into 62.5/125μm, 0.275 NA graded-index multimode fiber. The minimum power specified is at Beginning-of-Life. 3 The Center Wavelength, Spectral Width and Optical Rise/Fall Time satisfy the trade-off curves in FDDI PMD document as shown in Figure 1. 4 Defined as 12.6 times the rms value per FDDI PMD. 5 Compliance with the Optical Pulse Envelope in FDDI PMD is not specified and is not claimed. Receiver Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate Parameter Operating Data Rate 1 -10 2 Symbol B Pmin Pmax Plos+ Plost_loss_off t_loss_on DCD DDJ RJ λ Minimum - 32.5 - 14.0 Plos- + 1.5dB - 45.0 1.5 1100 Typical 125 - 34.5 0 - Maximum - 32.5 100 350 0.4 1.0 2.14 1600 Units Mb/s dBm dBm dBm dB µs ns ns ns nm Minimum Input Optical Power (2.5x10 BER) Increasing Light Input Maximum Input Optical Power (2.5x10-10 BER) 2 LOS Thresholds LOS Hysteresis LOS Timing Delay Increasing Light Input Decreasing Light Input Decreasing Light Input Contributed Duty Cycle Distortion Jitter (peak-to-peak) Contributed Data Dependent Jitter (peak-to-peak) Contributed Random Jitter (peak-to-peak) Wavelength of Operation 1 3 Data rate ranges from 50Mb/s to 266Mb/s. However, some degradation may be incurred in overall performance. 2 Specified in average optical input power and measured with 223-1 PRBS at 125Mb/s and 1310nm wavelength with optical input rise/fall time of 2.5ns and optimum sampling. 3 Defined as 12.6 times the rms value per FDDI PMD. Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements Oplink Communications, Inc. 2 RevB-P.2009.06.23 TRPNFEMM Transmitter Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Input Voltage Swing (TD+ & TD-) 1 Input HIGH Voltage (TX Disable) 2 Input LOW Voltage (TX Disable) 1 2 Symbol VPP-DIF VIH VIL Minimum 0.50 2.0 0 Typical - Maximum 2.4 VCC 0.8 Units V V V 2 Differential peak-to-peak voltage. There is an internal 4.7 to 10kΩ pull-up resistor to VccT. Receiver Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Output Voltage Swing (RD+ & RD-) 1 Output HIGH Voltage (LOS) 2 Output LOW Voltage (LOS) 1 2 Symbol VPP-DIF VOH VOL Minimum 0.6 2.0 0 Typical - Maximum 2.0 VCC + 0.3 0.5 Units Vp-p V V 2 Differential peak-to-peak voltage across external 100Ω load. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Electrical Power Supply Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Supply Voltage Supply Current Symbol VCC ICC Minimum 3.13 Typical 3.3 222 Maximum 3.47 245 Units V mA Module Definition MOD_DEF(0) pin 6 TTL LOW MOD_DEF(1) pin 5 SCL MOD_DEF(2) pin 4 SDA Interpretation by Host Serial module definition protocol Electrical Pad Layout 20 19 18 17 16 15 14 13 12 11 TX GND TD- (TX DATA IN-) TD+ (TX DATA IN+) TX GND VccTX VccRX RX GND RD+ (RX DATA OUT+) RD- (RX DATA OUT-) RX GND Host Board Connector Pad Layout 1 2 3 4 5 6 7 8 9 10 TX GND TX Fault TX Disable MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) NO CONNECTION LOS RX GND RX GND 1 2 3 Toward Bezel 20 19 18 17 16 15 14 13 12 11 Toward ASIC 4 5 6 7 8 9 10 Top of Board Bottom of Board (as viewed thru top of board) Pin 2 Internally Grounded. Oplink Communications, Inc. 3 RevB-P.2009.06.23 TRPNFEMM Example of SFP host board schematic 1µH coil or ferrite bead (