TRPA12MSM

Multi-rate OC-12/STM-4 SFP Transceivers with Digital Diagnostics TRPA12M SM Product Description The TRPA12M SFP series of multi-rate fiber optic transceivers with integrated digital diagnostics monitoring functionality provide a quick and reliable interface for OC-12 short reach (SR), intermediate reach (IR) and long reach (LR) applications. The diagnostic functions, alarm and warning features as described in the Multi-Source Agreement (MSA) document, SFF-8472 (Rev. 9.3), are provided via an I2C serial interface. Available products under this series are compliant with SONET/SDH standards for OC-12/STM-4 applications and are capable of operating down to 155Mb/s data rate. The SR-1 and IR-1 versions are compliant with OC-12/ STM-4 and OC-3/STM-1 interface standards. All modules satisfy Class I Laser Safety requirements in accordance with the U.S. and international standards as described in the FDA/CDRH and IEC-60825 documents, respectively. The TRPA12M multi-rate transceivers connect to standard 20-pad SFP connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different types of transceivers without shutting down the power supply of the host system. The transceivers have colored bail-type latches, which offer an easy and convenient way to release the modules. The latch is compliant with the SFP MSA. The transmitter design incorporates a highly reliable 1310nm or 1550nm InGaAsP laser and an integrated driver circuit. The receiver features a transimpedance amplifier IC optimized for high sensitivity and wide dynamic range. The transmitter and receiver DATA interfaces are AC-coupled internally. LVTTL Transmitter Disable control input and Loss of Signal output interfaces are also provided. The transceivers operate from a single +3.3V power supply over two operating case temperature ranges of -5°C to +70°C and -40°C to +85°C. Features  Compliant with SONET/SDH OC-12/STM-4 (622Mb/s)  Compatible with SONET/SDH OC-3/STM-1 (155Mb/s)  Compatible with SFP MSA  SONET/SDH Reaches (SR-1, IR-1, LR-1 & LR-2)  Digital Diagnostics through Serial Interface  Internal Calibration for Digital Diagnostics  Eye Safe (Class I Laser Safety)  Duplex LC Optical Interface  -40°C to +85°C Operating Temperature Option  Excellent EMI & ESD Protection  Hot-pluggable  TX Fault & Loss of Signal Outputs  TX Disable Input  Single +3.3V Power Supply Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature 1 Supply Voltage Input Voltage 1 Symbol Tst “B” option “A” option Top Vcc Vin Minimum - 40 -5 - 40 0 0 Maximum + 85 + 70 + 85 + 5.0 + 5.0 Units °C °C V V Measured on top side of SFP module at the front center vent hole of the cage. An Oplink Company RevC-P.2009.04.01 TRPA12M Single Mode Multi-rate Transmitter Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Operating Data Rate Average Optical Output Power (coupled into single mode fiber), 50% duty cycle Transmitter OFF Output Power Extinction Ratio SR-1 & IR-1 LR-1 & LR-2 SR-1 Center Wavelength 1 Symbol B SR-1 & IR-1 LR-1 & LR-2 PO POFF Phi /Plo Minimum 125 - 15.0 - 3.0 8.2 10 1261 1274 Typical - 11.0 - 1.0 1310 1310 1310 1310 1550 - Maximum 622 - 8.0 + 2.0 - 45.0 1360 1356 1334 1335 1580 4.0 2.5 or 4.0 1.0 - Units Mb/s dBm dBm dB IR-1 LR-1 LR-2 SR-1 IR-1 LR-1 & LR-2 LR-1 & LR-2 λC 1293 1280 1480 30 nm Spectral Width (RMS) 1 Spectral Width (-20dB) Side Mode Suppression Ratio Optical Output Eye 1 ΔλRMS Δλ20 SMSR nm nm dB Compliant with Telcordia GR-253-CORE and ITU-T Recommendation G.957 For IR version, the center wavelength is either 1274nm ≤ λc ≤ 1356nm for ΔλRMS ≤ 2.5nm or 1293nm ≤ λc ≤ 1334nm for ΔλRMS ≤ 4.0nm Receiver Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Operating Data Rate Receiver Sensitivity (10 BER) -10 1 -10 1 Symbol B Pmin Pmax Plos+ Plost_loss_off t_loss_on λ - Minimum 125 - 28.0 - 7.0 - 45.0 2.3 0.5 1100 - Typical - 31.0 - 3.0 1.5 - Maximum 622 - 28.0 100 100 1600 - 27.0 23 Units Mb/s dBm dBm dBm µs dB nm dB Maximum Input Optical Power (10 BER) LOS Thresholds 1 LOS Timing Delay LOS Hysteresis Wavelength of Operation Receiver Reflectance (LR-2) 1 Increasing Light Input Decreasing Light Input Increasing Light Input Decreasing Light Input Specified in average optical input power and measured at 155Mb/s & 622Mb/s and 1310nm wavelength (1550nm for LR-2) with 2 -1 PRBS, and at 125Mb/s with 27-1 PRBS. Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements Oplink Communications, Inc. 2 RevC-P.2009.04.01 TRPA12M Single Mode Multi-rate Transmitter Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Input Voltage Swing (TD+ & TD-) 1 Input HIGH Voltage (TX Disable) 2 Input LOW Voltage (TX Disable) Output HIGH Voltage (TX Fault) 1 2 Symbol VPP-DIF VIH VIL VOH VOL Minimum 0.25 2.0 0 2.0 0 Typical - Maximum 2.4 VCC 0.8 VCC + 0.3 0.8 Units V V V V V 2 3 Output LOW Voltage (TX Fault) 3 Differential peak-to-peak voltage. There is an internal 4.7 to 10kΩ pull-up resistor to VccT. 3 Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Receiver Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Output Voltage Swing (RD+ & RD-) 1 Output HIGH Voltage (LOS) 1 2 Symbol VPP-DIF VOH VOL Minimum 0.6 2.0 0 Typical - Maximum 2.0 VCC + 0.3 0.5 Units V V V 2 Output LOW Voltage (LOS) 2 Differential peak-to-peak voltage across external 100Ω load. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Electrical Power Supply Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Supply Voltage Supply Current Symbol VCC ICC Minimum 3.13 Typical 3.3 210 Maximum 3.47 275 Units V mA Module Definition MOD_DEF(0) pin 6 TTL LOW MOD_DEF(1) pin 5 SCL MOD_DEF(2) pin 4 SDA Interpretation by Host Serial module definition protocol Electrical Pad Layout 20 19 18 17 16 15 14 13 12 11 TX GND TD- (TX DATA IN-) TD+ (TX DATA IN+) TX GND VccTX VccRX RX GND RD+ (RX DATA OUT+) RD- (RX DATA OUT-) RX GND Host Board Connector Pad Layout 1 2 3 4 5 6 7 8 9 10 TX GND TX Fault TX Disable MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) NO CONNECTION LOS RX GND RX GND 1 2 3 Toward Bezel 20 19 18 17 16 15 14 13 12 11 Toward ASIC 4 5 6 7 8 9 10 Top of Board Bottom of Board (as viewed thru top of board) Oplink Communications, Inc. 3 RevC-P.2009.04.01 TRPA12M Single Mode Multi-rate Example of SFP host board schematic Vcc 3.3V 1µH coil or ferrite bead (