TRPAG1SXLAES

Gigabit Ethernet SFP Multimode Transceiver with Digital Diagnostics TRPAG1SXLAES Product Description The TRPAG1SXLAES SFP ber optic transceiver with integrated digital diagnostics monitoring functionality provides a quick and reliable interface for Gigabit Ethernet1000BASE-SX multimode applications. The diagnostic functions, alarm and warning features as described in the Multi-Source Agreement (MSA) document, SFF-8472(Rev. 9.4), are provided via an I2C serial interface. A highly reliable 850nm wavelength Vertical Cavity Surface Emitting Laser (VCSEL) is used in the transmitter. The transceiver satises Class I Laser Safety requirements in accordance with the U.S. FDA/CDRH and international IEC-60825 standards. The TRPAG1SXLAES transceiver connects to a standard 20-pad SFP connector for hot plug capability. This allows the system designer to make conguration changes or maintenance by simply plugging in dierent types of transceivers without removing the power supply from the host system. The transceiver has bail-type latch, which oers an easy and convenient way to release the module. The latch is compliant with the SFP MSA. The transmitter and receiver DATA interfaces are AC coupled internally. LV-TTL Transmitter Disable controlinput and Loss of Signal output interfaces are also provided. The transceiver operates from a single +3.3V power supply over an operating case temperature range of -40°C to+85°C. The housing is made of plastic and metal for EMI immunity. Features  Compatible with SFP MSA  Compliant with IEEE 802.3z Gigabit Ethernet 1000BASE-SX PMD Specifications  Digital Diagnostics through Serial Interface  Internal Calibration for Digital Diagnostics  Industrial Operating Temperature Range  275m Distance with 62.5μm Multimode Fiber  550m Distance with 50μm Multimode Fiber  TX Disable Input  Hot-pluggable Eye Safe (Class I Laser Safety)  Duplex LC Optical Interface  Single +3.3V Power Supply Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature1 Supply Voltage Input Voltage 1 Symbol VST Industrial2 VOP VCC VIN Minimum - 40 - 40 0 0 Maximum + 85 + 85 + 5.0 VCC Units °C °C V V Measured on top side of SFP module at the front center vent hole of the cage. An Oplink Company RevB-NP.2008.00909 TRPAG1SXLAES Transmitter Performance Characteristics All parameters guaranteed only at typical data rate Parameter Operating Data Rate 1 Optical Output Power 2 Center Wavelength Spectral Width (RMS) Extinction Ratio Total Jitter Relative Intensity Noise Coupled Power Ratio Transmitter Output Eye 1 2 (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Symbol B PO λC ΔλRMS Phi /Plo TJ RIN CPR Minimum - 9.5 820 9 9 Typical 1250 - 7.0 - Maximum - 4.0 860 0.85 227 - 117 - Units Mb/s dBm nm nm dB ps dB/Hz dB Compliant with Eye Mask Dened in IEEE 802.3z Standard Data rate ranges from 1000Mb/s to 1300Mb/s. However, some degradation may be incurred in overall performance. Measured average power coupled into either 50μm or 62.5μm multimode fiber. Receiver Performance Characteristics All parameters guaranteed only at typical data rate Parameter Operating Data Rate 1 Minimum Input Optical Power (10 -12 (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Minimum - 17.0 0 - 30.0 0.5 770 12 Typical 1250 Compliant with 802.3z Standard Maximum - 17.0 266 860 1500 Units Mb/s dBm dBm dBm dB ps nm dB MHz Symbol B BER) 2 Pmin Pmax Plos+ PlosTJ λ ORL - Maximum Input Optical Power (10 -12 BER) 2 LOS Thresholds LOS Hysteresis Total Jitter Wavelength of Operation Optical Return Loss Electrical 3dB Upper Cuto Frequency Stressed Receiver Sensitivity 1 2 Increasing Light Input Decreasing Light Input Data rate ranges from 1000Mb/s to 1300Mb/s. However, some degradation may be incurred in overall performance. Measured with 27-1 PRBS at 1250Mb/s and 850nm wavelength. Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements Oplink Communications, Inc. 2 RevB-NP.2008.00909 TRPAG1SXLAES Transmitter Performance Characteristics Parameter Input Voltage Swing (TD+ & TD-) 1 Input HIGH Voltage (TX Disable) Input LOW Voltage (TX Disable) Output LOW Voltage (TX Fault) 1 2 3 (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Minimum 0.50 2.0 0 2.0 0 Typical Maximum 2.4 VCC 0.8 VCC +0.3 0.8 Units V V V V V Symbol VPP-DIF VIH VIL VOH VOL 2 2 Output HIGH Voltage (TX Fault) 3 3 Differential peak-to-peak voltage. There is an internal 4.7 to 10kΩ pull-up resistor to VccT. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Receiver Electrical Interface Parameter Output Voltage Swing (RD+ & RD-) Output HIGH Voltage (LOS) Output LOW Voltage (LOS)) 1 2 (Over Operating Case Temperature. VCC = 3.13 to 3.47V)) Symbol Minimum 0.6 2.0 0 Typical Maximum 2.0 VCC +0.3 0.5 Units V V V 1 VPP-DIF VOH VOL 2 2 Differential peak-to-peak voltage across external 100Ω load. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Electrical Power Supply Characteristics Parameter Supply Voltage Supply Current VCC ICC (Over Operating Case Temperature. VCC = 3.13 to 3.47V)) Minimum 3.13 Typical 3.3 175 Maximum 3.47 245 Units V mA Symbol Module Definition MOD_DEF(0) pin 6 MOD_DEF(1) pin 5 MOD_DEF(2) pin 4 Interpretation by Host TTL LOW SCL SDA Serial module denition protocol Electrical Pad Layout 20 19 18 17 16 15 14 13 12 11 TX GND TD- (TX DATA IN-) TD+ (TX DATA IN+) TX GND VccTX VccRX RX GND RD+ (RX DATA OUT+) RD- (RX DATA OUT-) RX GND Host Board Connector Pad Layout 20 19 18 17 16 15 14 13 12 11 Toward ASIC 1 2 3 4 5 6 7 8 9 10 TX GND TX Fault TX Disable MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) NO CONNECTION LOS RX GND RX GND 1 2 3 Toward Bezel 4 5 6 7 8 9 10 Top of Board Bottom of Board (as viewed thru top of board) Oplink Communications, Inc. 3 RevB-NP.2008.00909 TRPAG1SXLAES Example of SFP host board schematic Vcc 3.3V 1μH coil or ferrite bead (