OPB760

Product Bulletin OPB750N June 1996 Reflective Object Sensor Type OPB750N Features • High contrast ratio 1000 to 1 minimum • Printed circuit board mount • Low cost plastic housing Description The OPB750N reflective assembly features a phototransistor output designed to decrease low-level light gain while not affecting the high-level light gain. Available with two mounting tabs as OPB750T. Available with 12", 26 AWG wire leads as OPB755 series. Photologic® output sensors available in OPB760/OPB770 series. Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage and Operating Temperature Range . . . . . . . . . . . . . . . . . . . -40o C to +85o C Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 sec. with soldering iron] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240o C(2) Input Diode Forward DC Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Peak Forward Current (1 µs pulse width, 300 pps) . . . . . . . . . . . . . . . . . . . . . . . 3.0 A Reverse DC Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 V Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW Output Phototransistor Collector-Emitter Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V Collector DC Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW Notes: (1) Derate Linearly 1.67 mW/o C above 25o C. (2) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. (3) All parameters tested using pulse technique. (4) Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and ketones. (5) Photocurrent is measured using an Eastman Kodak Neutral White test card having a 90% diffuse reflectance as a reflecting surface. Reference: Eastman Kodak, Catalog #1257795. (6) IC(OFF) is the photocurrent measured with current to the input diode and a 5% reflecting surface. Optek Technology, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 11-42 (972) 323-2200 Fax (972) 323-2396 Type OPB750N Electrical Characteristics (TA = 25o C unless otherwise noted) SYMBOL Input Diode VF IR V(BR)CEO ICEO PARAMETER MIN MAX UNITS 1.80 100 30 100 0.40 500 375 250 250 V µA V nA V µA µA µA nA IF = 40 mA VR = 2.0 V IC = 100 µA TEST CONDITIONS Forward Voltage Reverse Current Collector-Emitter Breakdown Voltage Collector Dark Current Saturation Voltage On-State Collector Current Output Phototransistor VCE = 10 V, IF = 0, H = 0 IC = 150 µA, IF = 30 mA, d = 0.22” (5) VCE = 5 V, IF = 30 mA, d = 0.08” (5) VCE = 5 V, IF = 30 mA, d = 0.15” (5) VCE = 5 V, IF = 30 mA, d = 0.22” Coupled VCE(SAT) IC(ON) Off-State Collector Current IC(OFF) IF = 30 mA, VCE = 5 V(6), d = 0.08” 0.15” 0.22” , , Typical Performance Curves Normalized Collector Current vs. Object Distance Normalized to d = .150" IF = 30 mA VCE = 5 V Average Normalized Ouput Current vs. Forward Current Normalized to IF = 30 mA VCE = 5 V +2σ Average -2σ +2σ -2σ Distance to Reflective Surface - Inches Forward Current - mA Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. Optek Technology, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 (972) 323-2200 Fax (972) 323-2396 11-43