OPB806_05

Slotted Optical Switch OPB806 Features: • • • • Non-contact switching Base or side mounting 0.125” (3.175 mm) slot width 0.500” (12.700 mm) lead spacing Product Photo Here Description: The OPB806 slotted optical switch consists of an infrared emitting diode (LED) and a NPN silicon phototransistor, mounted on opposite sides of a 0.125” (3.175 mm) wide slot. The OPB806 has two sets of mounting tabs allowing Base or Side mounting of the device. phototransistor leads project from each side of the housing on 0.050” (1.27 mm) centers. Phototransistor switching takes place whenever an opaque object passes through the slot. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. The LED and Applications: • • • • • Non-contact interruptive object sensing Assembly line automation Machine automation Equipment security Machine safety LED Peak Part Number Wavelength OPB806 935 nm Sensor Transistor Slot Width / Depth 0.125" / 0.375” Aperture None Lead Length 0.500" 1 3 2 4 Pin # 1 2 3 4 Description Anode Cathode Collector Emitter RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 12/05 Page 1 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Slotted Optical Switch OPB806 Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage & Operating Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] (1) Input Diode Continuous Forward Current Peak Forward Current (1 µs pulse width, 300 pps) Reverse Voltage Power Dissipation (2) Output Phototransistor Collector-Emitter Voltage Emitter-Collector Voltage Power Dissipation (2) -40° C to +85° C 260° C 50 mA 3A 2V 100 mW 30 V 5V 100 mW Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP165 for additional information) VF IR Forward Voltage Reverse Current 1.7 100 V µA IF = 20 mA VR = 2 V Output Phototransistor (See OP505 for additional information) V(BR)CEO V(BR)ECO ICEO Combined VCE(SAT) IC(ON) Collector-Emitter Saturation Voltage On-State Collector Current 0.4 0.5 V mA IC = 200 µA, IF = 20 mA VCE = 0.5 V, IF = 20 mA Collector-Emitter Breakdown Voltage Emitter-Collector Breakdown Voltage Collector-Emitter Dark Current 30 5 100 V V nA IC = 100 µA IE = 100 µA VCE = 10 V, IF = 0, EE = 0 Notes: (1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (2) Derate linearly 1.67 mW/°C above 25 ° C.. (3) Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and ketones. (4) All parameters were tested using pulse technique. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 12/05 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Slotted Optical Switch OPB806 OPB806 - Flag Next to Emitter 1.20 OPB806 - Flag Next to Sensor 1.20 1.00 1.00 0.80 Typical I C(ON) Response (mA) Typical I C(ON) Response (mA) 0.80 0.60 0.60 0.40 0.40 0.20 Right to Left Left to Right Top to Bottom Right to Left 0.20 Left to Right Top to Bottom 0.00 0.00 0.05 0.10 0.15 0.20 0.00 0.00 0.05 0.10 0.15 0.20 Displacement Distance (inches) Displacement Distance (inches) OPB806 - Flag in Middle of Slot 1.20 Test Schematic 1.00 Typical I C(ON) Response (mA) 0.80 0.60 0.40 Right to Left 0.20 Left to Right Top to Bottom 0.00 0.00 0.05 0.10 0.15 0.20 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A 12/05 Page 3 of 3