OPB854A3

Slotted Optical Switch OPB854A1, OPB854A2, OPB854A3 OPB854B1, OPB854B2, OPB854B3 Features: • • • • • Opaque housing material for ambient light rejection Non-contact switching Printed circuit board mounting, lead spacing 0.300” (7.62 mm) Slot width 0.100” (2.54 mm) Choice of three mounting configurations OPB854_1 Product Photo Here OPB854_2 OPB854_3 Description: Each OPB854 series contains an Infrared Light Emitting Diode (LED) and an NPN silicon phototransistor mounted on opposite sides of a 0.100” (2.54 mm) wide slot in an opaque plastic housing. The OPB854 series has an equivalent aperture of 0.60” (1.52 mm) in diameter because of the lens on the emitting an sensing devices. The difference between the OPB854A aeries and OPB854B series are electrical characteristics. Switching of the phototransistor occurs whenever an opaque object passes through the slot. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: • • • • • Non-contact interruptive object sensing Assembly line automation Machine automation Equipment security Machine safety Part Number OPB854A1 OPB854B1 OPB854A2 OPB854B2 OPB854A3 OPB854B3 890 nm LED Peak Wavelength Ordering Information Sensor Slot Width / Depth Aperture Emitter/Sensor Lead Length / Spacing Transistor 0.100" / 0.250” None 0.400" / 0.300" RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A .1 12/06 Page 1 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Slotted Optical Switch OPB854A1, OPB854A2, OPB854A3 OPB854B1, OPB854B2, OPB854B3 1 4 2 3 Pin # 1 2 3 4 Description Anode Cathode Emitter Collector 0 Top to Bottom Flag Travel for Graphs on page 4 Emitter Left to Right Right to Left Sensor 0 Width [ MILLIMETERS] DIMENSIONS ARE IN: INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A .1 12/006 Page 2 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Slotted Optical Switch OPB854A1, OPB854A2, OPB854A3 OPB854B1, OPB854B2, OPB854B3 Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage & Operating Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron](1) Input Diode Forward DC Current Peak Forward Current (1 μs pulse width, 300 pps) Reverse DC Voltage Power Dissipation(2) Output Phototransistor Collector-Emitter Voltage Emitter-Collector Voltage Collector DC Current Power Dissipation(2) 30 V 5V 30 mA 100 mW 50 mA 3A 2V 100 mW -40° C to +85° C 260° C Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (see OP140 for additional information) VF IR Forward Voltage Reverse Current 1.7 10 V µA IF = 20 mA VR = 2 V Output Phototransistor (see OP550 for additional information) V(BR)CEO V(BR)ECO ICEO Combined VCE(SAT) Collector-Emitter Saturation Voltage OPB854A series OPB854B series On-State Collector Current OPB854A series OPB854B series 3 1 0.6 0.4 IC = 2 mA, IF = 16 mA IC = 250 µA, IF = 20 mA VCE = 1 V, IF = 16 mA VCE = 10 V, IF = 20 mA Collector-Emitter Breakdown Voltage Emitter-Collector Breakdown Voltage Collector Dark Current 30 5 100 V V nA I C = 1 mA IE = 100 µA VCE = 10 V, IF = 0, EE = 0 V IC(ON) Notes: (1) (2) (3) (4) (5) (6) mA RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.67 mW/°C above 25 ° C. All parameters tested using pulse techniques. Lead spacing of 0.220” (5.59 mm) or 0.320” (8.13 mm) is available. Leads are 0.20” sq. (5.1 mm) and 0.425” (10.8 mm) long (minimum). Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and ketones. Polarity is denoted by color of housing top (gray or clear LED, black sensor). OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A .1 12/06 Page 3 of 4 Slotted Optical Switch OPB854A1, OPB854A2, OPB854A3 OPB854B1, OPB854B2, OPB854B3 Flag Next to Emitter 1.2 Top to Bottom Flag Next to Sensor 1.2 Top to Bottom 1.0 1.0 Normalized IC(ON) Response Normalized IC(ON) Response 0.8 0.8 Left to Right Right to Left Left to Right Right to Left 0.6 0.6 0.4 0.4 0.2 0.2 0.0 0.00 0.05 0.10 0.15 0.20 0.25 0.0 0.00 0.05 0.10 0.15 0.20 0.25 Distance (inches) Distance (inches) Flag in Middle of Slot 1.2 Top to Bottom Output Current vs Forward Current vs Temperature 2.0 1.8 1.6 Normalized at IF = 16mA, TA = 20°C, VCE = 5V 1.0 Normalized IC(ON) Response 0.8 Normalized Output Current 1.4 1.2 1.0 0.8 0.6 0.4 0.2 -40° C -20° C 0° C 20° C 40° C 60° C 80° C Left to Right Right to Left 0.6 0.4 0.2 0.0 0.00 0.0 0.05 0.10 0.15 0.20 0.25 0 5 10 15 20 25 30 35 40 45 50 Displacement Distance (inches) Forward Current - mA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A .1 12/006 Page 4 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com