OPR5011_07

Optical Comparator Array OPR5011 Features: • • • • • Precise active area location Surface mountable TTL compatible output Wide supply voltage range Wide operating temperature range Description: Each OPR5011 device is a hybrid sensor array that consists of three channels of the OPTEK OPC8332 differential optical comparator (‘TRI-DOC”) IC. The single chip construction ensures very tight dimensional tolerances between active areas. Specifically designed for high-speed/high-resolution encoder applications, the open collector output switches based on the comparison of the input photodiode’s light current levels. Logarithmic amplification of the input signals facilitates operation over a wide range of light levels. The surface-mountable opaque polyimide package shields the photodiodes from stray light and can withstand multiple exposures to the most demanding soldering conditions, while the gold-plated wraparound contacts provide exceptional storage and wetting characteristics. Applications: • • • High-speed applications High-resolution applications Applications requiring a wide range of light levels Sensor Differential Optical OPR5011 Comparator Part Number Ordering Information Optical # of Icc (mA) Hysteresis (%) Elements Typ / Max Typical 3 9 / 20 40.00 Optical Offset (%) Min / Max -40/+40 NOTE: SEE PAGE 2 FOR APPLICATION CIRCUIT. DIMENSIONS ARE IN: [MILLIMETERS] INCHES Pin # Description Pin # Description Pin # Description Pin # Description 1 2 3 4 B - Output B - Vcc A + Trim A -Trim 5 6 7 8 N.C. A - Output A - Vcc Common 9 10 11 12 Z + Trim Z -Trim Z - Output Z - Vcc 13 14 B + Trim B -Trim RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 01/07 Page 1 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optical Comparator Array OPR5011 Application Circuit - OPR5011 Notes: (1) The 74L2)4 is recommended as a means of isolating the “DOC” comparator circuitry from transients induced by inductive and capacitive loads. (2) It is recommended that a decoupling capacitor be placed as close as possible to the device. Block Diagram - OPC8332 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 01/07 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optical Comparator Array OPR5011 Absolute Maximum Ratings (TA = 25° C unless otherwise noted) Storage and Operating Temperature Supply Voltage Output Voltage Output Current Power Dissipation Solder reflow time within 5°C of peak temperature is 20 to 40 seconds (1) -40° C to +100° C 24 V 24 V 14 mA 500 mW 250° C Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL ICC VOL IOH PARAMETER Supply Current Low Level Output Voltage (4)(7) (2) (3) MIN -40 TYP 9 0.3 0.1 40 10 1 1 300 MAX 20 0.4 1 +40 - UNITS mA V µA % % MHz µs ns TEST CONDITIONS VCC = 24 V IOL = 14 mA, VCC = 4.5 V VCC = VO = 20 V VCC = 5 V, IOL = 1 mA VCC = 5 V, IOL = 1 mA High Level Output Current (4)(7) (5) OPT-HYS Optical Hysteresis OPT-OFF Optical Offset fmax tlh thl Notes: (1) (2) (3) (4) (5) (6) (7) Frequency Response Output Rise Time Output Fall Time (6) - VCC = 5 V (6) Solder time less than 5 seconds at temperature extreme. Pin (+) = 100.0 nW and Pin (-) = 1.0 µW . Pin (+) = 1.0 µW and Pin (-) = 100.0 nW. Pin (-) is held at 1.0 µW while Pin (+) is ramped from 0.5 µW to 1.5 µW and back to 0.5 µW. Pin (+) is modulated from 1.0 µW to 2.0 µW. Pin (-) is modulated from 1.0 µW to 2.0 µW with phase shifted 180° with respect to Pin (+). Use 100 kΩ trimpot to set the output signal to 50% duty cycle for maximum operating frequency. Measured between 10% and 90% points. Optical Hysteresis and Optical Offset are found by placing 1.0 µW of light on the inverting photodiode and ramping the light intensity of the non-inverting input from 0.5 µW up to 1.5 µW and back down. This will produce two trigger points – an upper trigger point and lower trigger point. These points are used to calculate the optical hysteresis and offset. These are defined as: % Optical Hysteresis = 100 x (P rise - P fall) P in (-) % Optical Offset = 100 x (P average - P (-)) P in (-) Where: P in (-) P rise P fall P average = Light level incident upon the “-” photodiode on the IC chip (Pin) (-) = 1.0 µW). = Value of light power level incident upon the “+” photodiode that his required to switch the digital output when the light level is an increasing level (rising edge). = Value of light power level incident upon the “+” photodiode that is required to switch the digital output when the light level is decreasing level (falling edge). = (P rise + P fall) 2 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A 01/07 Page 3 of 3