OPV315

Vertical Cavity Surface Emitting Laser in TO-46 Package Features • • • • • • • • • 850nm VCSEL Technology Data rates up to 2.5 Gbps High thermal stability Low drive current/high output density Narrow and concentric beam angle Recommended for multimode fiber applications TO-46 package with microbead lens Burned in for communication level reliability Monitor photodiode Description The OPV315 is a high performance 850nm VCSEL packaged for high speed communication links. OPV315 combines all the performance advantages of a VCSEL with the addition of a power monitor diode for precise control of optical power. The OPV315Y is identical electrically and optically and differs only in pin out. Refer to mechanical drawings for details. Features including high speed, high output power and concentric beam makes it an ideal transmitter for integration into all types of data communications equipment. Applications include: Absolute Maximum Ratings (TA = 25° C unless otherwise noted) Storage Temperature Operating Temperature Soldering Lead Temperature Maximum Forward Peak Current Maximum Reverse Voltage Max. Continuous Optical Power @ 70° C 85° C -40° C to +100° C 0° C to +70° C 260° C for 10 Seconds 20 mA 10 V 750 µW 500 µW ♦ ♦ ♦ ♦ ♦ ♦ Fibre Channel Gigabit Ethernet ATM VSR Intra-system links Optical backplane interconnects. Additional laser safety information can be found on the Optek website. See application #221. Classification is not marked on the device due to space limitations. See package outline for centerline of optical radiance. Operating devices beyond maximum rating may cause devices to exceed rated classification September 2003 Issue 2.3 Optek Technology, Inc. Carrollton, Texas 75006 (972) 323-2200 sensors@optekinc.com www.optekinc.com Page 1 of 4 OPV315, OPV315Y Technical Data Electrical/Optical Characteristics (at 25 C unless otherwise specified) SYMBOL POT ITH VF IR RS PARAMETER Total Power Out Threshold Current Forward Voltage Reverse Current Series Resistance Slope Efficiency Linearity MIN 0.75 0.80 1.60 TYP MAX 3.00 2.20 35 UNITS mW mA V nA ohms mW/mA Note1 TEST CONDITION IF = 7 mA IF = 7 mA VR = 5 V Note 2 Note 3 Note 4 20 0.10 0.00 840 850 55 η λ ∆λ tr tf NRI ∆lTH/∆T ∆λ/∆T ∆VF∆T ∆η/∆T W avelength Optical Bandwidth Rise Time Fall Time Relative Intensity Noise Temp Coefficient of Threshold Current Temp Coefficient of Wavelength Temperature Coefficient for VF Temperature Coefficient for Efficiency 860 0.85 nm nm ps ps db/Hz mA %/° C mV/° C %/C 0° - 70° C, Note 1 0° - 70° C, IF = 7 mA 0° - 70° C, IF = 7 mA 0° - 70° C, Note 3 20% to 80% 80% to 20% 90 120 -123 ±1.0 0.06 -2.5 -0.5 SYMBOL IRPD IM1 IM2 PARAMETER Reverse Current, photo diode Monitor Current Monitor Current MIN 30 40 TYP MAX 30 UNITS nA µA µA TEST CONDITION VR = 5 V IF = 7 mA, VR = 5 V PO = 2 mW, VR = 5 V Photodiode Electrical Characteristics (at 25 C unless otherwise specified) NOTES: (1) (2) (3) (4) Threshold Current is based on the two line intersection method specified in Telcordia GR-468-Core. Line 1 from 4 mA to 6 mA. Line 2 from 0 mA to 1 mA. Series Resistance is the slope of the Voltage-Current line from 5 to 8 mA. Slope efficiency, is the slope of the best fit LI line from 5 mA to 8 mA using no larger than .25 mA test interval points. Using data points taken for slope efficiency above, delta L/delta I shall be calculated for each adjacent pair of points. Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. Optek Technology, Inc. Carrollton, Texas 75006 (972) 323-2200 sensors@optekinc.com September 2003 Issue 2.3 www.optekinc.com Page 2 of 4 OPV315, OPV315Y Technical Data Normalized Output Power vs. Forward Current Normalized Output Power (7mA, 25 Forward Current (mA) Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. Optek Technology, Inc. Carrollton, Texas 75006 (972) 323-2200 sensors@optekinc.com September 2003 Issue 2.3 www.optekinc.com Page 3 of 4 OPV315, OPV315Y Technical Data Invisible Light emits from this surface 1) Tolerances are ±0.005 unless otherwise specified 2) Dimensions in inches [mm] OPV315 Pin 1 2 3 Connection VCSEL Anode VCSEL Cathode/PD Anode PD Cathode Pin 1 2 3 OPV315Y Connection VCSEL Cathode VCSEL Anode/PD Cathode PD Anode Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. Optek Technology, Inc. Carrollton, Texas 75006 (972) 323-2200 sensors@optekinc.com September 2003 Issue 2.3 www.optekinc.com Page 4 of 4