OTS-1VR2AR-A3-FC-IC

Optiva Standard, 1 Composite Video and 2 Audio ™ OTS-1V2A Composite Video and Audio The OTS-1V2A provides for the digital transmission of 1 Channel of Composite Video and 2 Channels of Analog Audio. Video System Design All units come in an insert card version. The cards can be inserted into our 16-slot, 19” rack-mountable card cage (OT-CC-16-100) or one of our smaller Optiva™ Desktop Card Racks (OT-DTCR Series). The Optiva™ Desktop Card Racks can handle one, two or four insert cards, creating compact, mountable, stand alone systems. The use of separate OT-DTCR enclosures allows for future flexibility and expansion as all cards are hot-swappable and can be used in any enclosure. Each one of our card housing units operate with an appropriate power supply. See “Accessories” for power supply specifications. Optiva™ Upgrade Path This system can be purchased without an optical port as an add-on to an existing Optiva™ system daisy-chain. (See “Non-Optical Version” below). The Optiva™ bandwidth requirement of this system is 361 Mbps. Audio In S T A T U S A L E R T S T A T U S A L E R T Audio Out Each insert card comes with a label identifying the specific protocols handled, connector pin-out and other vital information. For optimal bandwidth allocation, each insert card can daisy-chain with an additional card in the same chassis. See “Optiva™ Upgrade Path”. Audio Composite Video In ST, LC, SC or FC Composite Video Out ST, LC, SC or FC ™ Optiv a ™ Optiv a Data VAD Transmission VAD Transmission OTS-1VT2AT OTS-1VR2AR Features • Composite Video and Analog Audio over one fiber • 10-Bit Digital Transmission • TDM - Single Wavelength • Complies with SMPTE standards for Video transmission • Compatible with MDM-7000 Series for WDM and CWDM multiplexing • No EMI or RFI and no ground loops • Stand alone or rack-mount • Ideal for AV applications Versions Available* Wavelength (nm) & Fiber 1310 Multimode 1310 Singlemode 1310 Singlemode(D) 1550 Singlemode 1550 Singlemode (D) 1270-1610 SM (CWDM) Non-Optical Version Transmit** OTS-1VT2AT-A1-XX-IC OTS-1VT2AT-A2-XX-IC OTS-1VT2AT-A2D-XX-IC OTS-1VT2AT-A3-XX-IC OTS-1VT2AT-A3D-XX-IC OTS-1VT2AT-L4-XX-IC OTS-1VT2AT-NOC-IC Receive** OTS-1VR2AR-A1-XX-IC OTS-1VR2AR-A2-XX-IC OTS-1VR2AR-A2D-XX-IC OTS-1VR2AR-A3-XX-IC OTS-1VR2AR-A3D-XX-IC OTS-1VR2AR-L4-XX-IC OTS-1VR2AR-NOC-IC Optical Connector ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC N/A Optical Budget (dB) 10 7 12 17 25 Varies N/A Range*** (km) 3 10 20 40 60 20-70 N/A Form Factor IC (1-slot) IC (1-slot) IC (1-slot) IC (1-slot) IC (1-slot) IC (1-slot) IC (1-slot) Analog Audio Codes - To indicate your Analog Audio impedance preference, please use the following instead of "A" in the model number: "AB" = Input Balanced 600 Ohm, Output Balanced 600 Ohm; "ABH" = Input Balanced Hi-Z, Output Balanced Low-Z; and "AUH" = Input Unbalanced Hi-Z, Output Unbalanced Low-Z. * Contact Opticomm for other versions available. ** XX indicates the type of optical connector. Each of ST, FC, LC or SC are available. *** Chromatic dispersion and additional losses should be taken into account. 800-867-8426 • info@opticomm.com • www.opticomm.com • Contact Opticomm for custom requirements. Opticomm reserves the right to change specifications without notice Composite Video, Audio & Data Video Standard Bit Resolution Level Bandwidth Differential Gain Differential Phase Compatibility Signal to Noise Ratio Connector Analog Audio Level Bandwidth Signal to Noise Ratio Total Harmonic Distortion Signal Coding Connector SMPTE 170M; RS-250C 10-Bit Processing; 10-Bit Transmission 1.0 Volt p-p 5.5 MHz < 1% < 0.7° NTSC, PAL > 67 dB BNC (IEC 60169-8) Optiva™ Multi-Signal Optiva™ Configurable Transmission Platform Communication Platform Network Management Network Management SDI and HD-SDI SDI & HD-SDI Composite Video, Composite Video, Audio & Data Audio & Data Audio/FSK/Intercom RGB/VGA/DVI RGB/VGA/DVI Audio/FSK/Intercom 6 dBm In/Out 20 Hz to 20 KHz > 80 dB < 0.1% 24-bit Micro DB25 Impedance Options: Input Balanced 600 Ohm Balanced Hi-Z Unbalanced Hi-Z Data (Ethernet/Serial/USB) Data (Ethernet/Serial/USB) Output Balanced 600 Ohm Balanced Low-Z Unbalanced Low-Z CATV/RF & L-Band CATV/RF & L-Band Optical Switching, Routing Optical Switching, Routing & Redundancy & Redundancy Passive Multiplexing Passive Multiplexing Solutions Solutions 11 oz Enclosures, Racks Enclosures, Racks & Frames & Frames Power Supplies Power Supplies and Accessories & Accessories General Dimensions & Weight Operating temperature Storage temperature Humidity Operating voltage Consumption System Latency Local Monitoring Remote Monitoring Insert Card (IC): 6.3” L x 0.8” W x 4.0” H -20° C to +55° C -40° C to +85° C 0 to 95% non-condensing 9-12 VDC 1 Amp Max per Insert Card Less than 1ms (Audio