OD-880WHT

HIGH TEMPERATURE GaAlAs IR EMITTERS FEATURES • Extended operating temperature range ANODE (CASE) • No internal coatings .209 .220 .015 .183 .152 .187 .156 • No derating or heat sink required to 80°C .100 .041 All surfaces are gold plated. Dimensions are nominal values in inches unless otherwise specified. Window caps are welded to the case. 20 13 1.00 MIN. GLASS .006 HIGH MAX OD-880WHT .017 .036 45° ELECTRO-OPTICAL CHARACTERISTICS AT 25°C PARAMETERS Total Power Output, Po R CATHODE .143 .150 MB E .098 .112 TEST CONDITIONS IF = 100mA Peak Emission Wavelength, λP MIN 7 IF = 50mA CE Half Intensity Beam Angle, θ IF = 100mA Forward Voltage, VF Reverse Breakdown Voltage, VR IR = 10μA 5 DE VR = 0V Rise Time FE Fall Time MAX 880 Spectral Bandwidth at 50%, Δλ Capacitance, C TYP 9 UNITS mW nm 80 nm 80 Deg 1.55 30 1.9 Volts Volts 17 pF 0.5 μsec 0.5 μsec ABSOLUTE MAXIMUM RATINGS AT 25°C CASE 190mW LI Power Dissipation1 Continuous Forward Current 100mA 3A Reverse Voltage 5V OF Peak Forward Current (10μs, 300Hz)2 Lead Soldering Temperature (1/16" from case for 10sec) 260°C D 1Derate per Thermal Derating Curve above 25°C 2Derate linearly above 25°C EN THERMAL PARAMETERS Storage and Operating Temperature Range -65°C TO 150°C Maximum Junction Temperature 150°C Thermal Resistance, RTHJA1 370°C/W Typical Thermal Resistance, RTHJA2 120°C/W Typical 1Heat transfer minimized by measuring in still air with minimum heat conducting through leads 2Air circulating at a rapid rate to keep case temperature at 25°C 1260 Calle Suerte, Camarillo, California 93012 Phone: (805) 499-0335, Fax: (805) 499-8108 Email: sales@optodiode.com, Website: www.optodiode.com Revision February 26, 2013 HIGH TEMPERATURE GaAlAs IR EMITTERS 10 140 NO HEAT SINK 120 100 80 60 40 100 25 50 75 100 125 AMBIENT TEMPERATURE (°C) t = 500μs 150 T 80 70 TCASE = 25°C NO PRE BURN-IN PERFORMED RELATIVE POWER OUTPUT FE LI FORWARD CURRENT, IF (amps) 2 1 100 40 20 FORWARD I-V CHARACTERISTICS 3 10 60 0 –100 105 DE 104 80 CE IF = 100mA 50 4 1 DUTY CYCLE, D (%) MB E IF = 50mA 103 STRESS TIME, (hrs) 0.1 RADIATION PATTERN 90 102 t T Ip 100 IF = 20mA 101 D= t 0.1 DEGRADATION CURVE 60 t = 100μs 1 0.01 0.01 RELATIVE POWER OUTPUT (%) 0 t = 10μs 13 PEAK FORWARD CURRENT, Ip (amps) POWER DISSIPATION (mW) INFINITE HEAT SINK 160 20 RELATIVE POWER OUTPUT (%) TYPICAL CHARACTERISTICS MAXIMUM RATINGS 180 MAXIMUM PEAK PULSE CURRENT 20 THERMAL DERATING CURVE R 200 OD-880WHT –80 –60 –40 –20 0 20 40 BEAM ANGLE, θ(deg) 60 80 100 POWER OUTPUT vs TEMPERATURE 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 OF 0.6 0.5 –50 0 0 1 2 3 4 FORWARD VOLTAGE, VF (volts) 5 6 SPECTRAL OUTPUT 0 25 50 AMBIENT TEMPERATURE (°C) 75 100 POWER OUTPUT vs FORWARD CURRENT 1,000 EN D 100 80 POWER OUTPUT, Po (mW) RELATIVE POWER OUTPUT (%) –25 60 40 100 10 20 0 750 800 850 900 WAVELENGTH, λ(nm) 950 1,000 1 10 DC PULSE 10μs, 100Hz 100 1,000 FORWARD CURRENT, IF (mA) 10,000 1260 Calle Suerte, Camarillo, California 93012 Phone: (805) 499-0335, Fax: (805) 499-8108 Email: sales@optodiode.com, Website: www.optodiode.com Revision February 26, 2013