OSRB38C9BA

6.6*5.3*4.3mm Infrared Receiver Module OSRB38C9BA ■Features ● ■Outline Dimension 3.0±:secnareloT mm:tinU CCV .3 DNUORG .2 TUPTUO .1 Miniature size Built-in exclusive IC Wide half angle & long reception distance Good noise-proof capability High immunity against ambient light Side view ● ● ● ● ● ■Applications ● AV instruments (Audio, TV, VCR, CD player) Home appliances (Air-conditioner, Fan, Light.) Remote control for wireless devices 3 2 1 ● ● Supply Voltage Operating Temperature Storage Temperature Lead Soldering Temperature *1 Vcc Topr Tstg Tsol 6.0 -10 ~ +60 -20 ~ +75 260 V *1 At the position of 2mm from the bottom of the package within 5 seconds Supply Voltage Current Consumption Reception Distance B.P.F. Center Frequency Vcc Icc d Fo Input signal=0 200 2.7 15 - 3.0 0.9 20 37.9 940 5.5 1.5 - 5Lux, Vcc=3V KHZ nm Peak Wavelength Signal Output High level output voltage p So Vcc=3V Vcc=5V Vin=0V Isink=2.0mA --Active Low-- Voh Vol Bw 2.7 4.7 400 3.0 5.0 0.2 0.4 Low level output voltage Burst width tolerance *2 Half Angle Burst Wave=60 600 90 800 *2 The output tolerance of burst width received when transmitter sends the burst wave. LED & Application Technologies http://www.optosupply.com ti n U Item Symbol Condition deg sμ ) (Ta=25 s μ0 ℃ ℃ ℃ ℃ ■Electrical -Optical Characteristics Min. Typ. Max. V mA m V V V 0 0 Parameter Symbol Ratings Unit ) (Ta=25 ℃ ℃ ℃ ℃ - ■Absolute Maximum Rating ■Directivity ℃ ℃ VER A.0 ℃ ± θΔ λ 6.6*5.3*4.3mm Infrared Receiver Module OSRB38C9BA ■ Carrier Frequency Relative Reception Distance vs Transmitter carrier Frequency ■ For Noisy Power Supply In case of noisy power supply, please serially insert 10 ■ Block Diagram LED & Application Technologies http://www.optosupply.com sa dnuorg dna enil ccV ni roticapac citylortcele Fμ74 tuoba dna rotsiser Ω0 oF : s w oll of d VER A.0 6.6*5.3*4.3mm Infrared Receiver Module OSRB38C9BA ■ Testing Method Distance between emitter and detector specifies maximum distance that output waveform satisfies the standard (FIG-3) under the standard transmitter. a. Measuring place Indoor Without extreme reflection of light. b. Ambient light source Detecting surface illumination is 200 5Lux under ordinary white fluorescence lamp of no high frequency lightning. c. Standard transmitter Transmitter wave indicated in FIG-2 of standard transmitter is arranged to satisfy V measuring circuit specified in FIG-3 langis tseT Sensing Distance: d VCC GND Standard Transmitter OUT langis tuptuO FIG-1 emit ffoT noT ■ Precautions for Use a. Store and use where there is no force causing transformation or change in quality. b. Store and use where there is no corrosive gas or sea(salt) breeze. c. Store and use where there is no extreme humidity. d. Solder the lead pin within the condition of ratings. After soldering, do not add exterior force. e. Do not wash this device. Wipe the stains of diode side with a soft cloth. You can use the solvent, ethyl alcohol, or methyl alcohol only. f. To prevent static electricity damage to the pre-amp, make sure that the human body, the soldering iron are connected to ground before using. LED & Application Technologies http://www.optosupply.com VER A.0 emit ≧o ≧o ≧o su006 sm001=cycT 2-GIF su006 dT hoV loV oV DNG V5 oV tiucriC tnemrusaeM tuptuO rewoP 3-GIF ΩK01 Fu01 ± ± ± ± ± ± ± ± 50mVp-p under the ΩK01 DEL RI mn049 rettimsnarT dradnatS