BTR-3580G

Optoway BTR-3580G / BTR-3580-SPG FEATURES l l l l l l l l l l l BTR-3580G 1 *********************************************************************************************************************************************************************** 1550 nm TX / 1310 nm RX , 5V / 155 Mbps RoHS Compliant Single-Fiber Transceiver ********************************************************************************************************************************************************************** DESCRIPTION Single Fiber Bi-Directional Transceiver 1550 nm DFB LD Transmitter 1310 nm Receiver D istance Up to 80 km Industry Standard 1 x 9 Footprint Single +5 V Power Supply RoHS Compliant PECL Differential Inputs and Outputs 0 to 70oC Operating Temperature Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant The BTR-3580G series is high performance module for single fiber communications by using 1550 nm transmitter and 1310 nm receiver. The transmitter section uses a multiple quantum well DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated 1310 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. APPLICATIONS l WDM 155 Mb/s Links l SONET/SDH Equipment Interconnect l Fast Ethernet 100 Mb/s Links ORDER INFORMATION P/No. Bit Rate D istance (Mb/s) (km) 125/155 80 TX (nm) 1550 DFB RX (nm) 1310 Voltage (V) 5 Package Temp (oC) 0 to 70 TX Power (dBm) 2 to -3 RX Sens. RoHS (dBm) Compliant -35 Yes BTR-3580G 1X9 Note: 1. BTR-XXXXXG is 1X9 SC receptacle type package. 2. BTR-XXXXX-XPBBBG is 1X9 pigtail type package with different connector, A=S is SC connector, A=F is FC connector, A=T is ST connector, A=L is LC connector, A=M is MU connector; BBB is the length of fiber in cm. Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Soldering Temperature Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr --Vcc --Iout Min -40 0 0 GND 0 Max 85 70 260 6 Vcc 30 Units o C o C o C V V mA Notes 10 seconds on leads only Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Data Rate Power Supply Current Symbol Vcc Topr Icc Min 4.75 0 Typ 5.00 155 Max 5.25 70 170 280 Units V o C Mb/s mA ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1 0/1/2005 V3.0 Optoway Transmitter Specifications (0 oC < Topr < 70 oC, 4.75V < Vcc < 5.25V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Symbol Min Typ Max Units BTR-3580G Notes 2 *********************************************************************************************************************************************************************** Po -3 --2 dBm 1 1480 1580 nm λ ----1 nm -20 dB Width ∆λ ER 10 ----dB Compliant with Bellcore GR-253-CORE and ITU recommendation G.957 tr 2 ns 10% to 90% Values tf 2 ns 10% to 90% Values RIN -116 dB/Hz TJ 1.0 ns 2 IIL IIH VIH - VIL VIL - VCC V IH - VCC -350 350 300 -2.0 -1.1 -1.58 -0.74 µA µA mV V V 3 3 Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 223-1 PRBS with 72 ones and 72 zeros. 3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs. Receiver Specifications (0oC < Topr < 70oC, 4.75 V < Vcc < 5.25V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Electrical Data Output Voltage – Low Data Output Voltage – High Signal Detect Output Voltage -Low Signal Detect Output Voltage -High Symbol --Pin Pa Pd Min ---3 ---43 1.0 1260 -2.0 -1.1 -2.0 -1.1 Typ ----------Max -35 ---35 --4.0 1360 -1.58 -0.74 -1.58 -0.74 Units dBm dBm dBm dBm dB nm V V V V Notes 1 Transition: low to high Transition: high to low 2 3 3 3 3 V OL - VCC V OH - VCC V OL - VCC V OH - VCC Notes: 1.Minimum sensitivity and saturation levels at BER 1E-=10 for a 223-1 PRBS with 72 ones and 72 zeros. 2. At least 30 dB optical isolation for the wavelength 1480 to 1580 nm. 3. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 10/1/2005 V3.0 Optoway CONNECTION DIAGRAM Receiver Signal Ground 1 (Rx GND) Receiver Data Out 2 (RD+) Receiver Data Out Bar 3 (RD−) Signal Detect 4 (SD) Receiver Power Supply 5 (Rx Vcc) Transmitter Power Supply 6 (Tx Vcc) Transmitter Data In Bar 7 (TD− ) Transmitter Data In 8 (TD+) Transmitter Signal Ground 9 (Tx GND) N/C BTR-3580G 3 *********************************************************************************************************************************************************************** TOP VIEW N/C P IN 1 2 3 4 5 6 7 8 9 Symbol Rx GND RD+ RD− SD R x Vcc T x Vcc TD− TD+ Tx GND Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal +5V dc power for the receiver section +5V dc power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this plan to the trransmitter ground plane RECOMMENDED CIRCUIT SCHEMATIC The split-load terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 10/1/2005 V3.0 Optoway PACKAGE DIAGRAM Units in mm 1) Receptacle Type BTR-3580G 4 *********************************************************************************************************************************************************************** BTR-3580G 2) Pigtail Type BTR-3580-SP50G Note: Length L is 50± 3 cm. Other pigtail’s length is available upon request. Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 10/1/2005 V3.0